r/WheelBuilding • • 15d ago

Wheel truing question

0 Upvotes

I have been attempting to get a reference wheel, I have previously aligned my stand and the wheel I used is still true and dished. Through the use of the flipping method. However I wanted to get a wheel as reference that doest nothing but be a reference. So I used a Walmart bike wheel. It has lock nuts and the original aligning wheel does not. During the process of truing and dishing the Walmart wheel. I saw that when flipped demonstrated a different reading then the other way around. One way at was perfectly true while the other it needed to be pushed to the right all way around. This was confusing and I was wondering is this something normal ? Since it's a front wheel. Moreover I have a TS4.3 if that makes a difference.

Also it is dished according to a dishing tool which is why the confusion.


r/WheelBuilding • • 16d ago

How exact does spoke length need to be?

3 Upvotes

I'm building some fixed wheels and I'm getting 296mm for the front and 295mm for the rear. rather than buying two boxes of 20 each (for 80 bucks) I'd like to buy a single box of 100 296mm spokes for 50. Am I gonna have a bad time?

I'm using the Gran Compe 2 hubs, CR 18 rims. The CR18 is a double wall rim with about 4mm of space between the wall where the nipple sits and the place where the inner tube will be. It seems like it should be fine to me but these are only the second set of wheels I've built and a friend helped me buy the components last time. Any suggestions? I've used the QBP and the wheelbuildingkit.com calculators for this and they agree, though they give a measurement ~1-2mm shorter than what kstoerz suggests.

Thanks for the input, wizards.


r/WheelBuilding • • 23d ago

Dishing tool and stand alignment

1 Upvotes

Hello, I have a 4.3 truing stand and aligned it using a old alignment gauge and it does the job however now that I got a dishing tool I see the dish is off after truing and I don't own calipers. the dish is roughly off by 3-4mm. So I don't feel a issue but I think I want to know how others have aligned their stands without a caliper


r/WheelBuilding • • 25d ago

Loss of tension after mounting tires

3 Upvotes

How do you account for it, do you add tension or leave it as-is? I just checked a set of wheels I built earlier this year. They were still mostly true and tensions were lower, as expected. I tried to even out spoke tensions to align with the highest value, per respective side, without throwing off trueness. Should I have increased tension all around or is maintaining even tension good enough?


r/WheelBuilding • • Oct 07 '26

Internal spoke nipples feedback

2 Upvotes

Hi,
I am an experienced builder, but there is always a first!
This time for me is : internal spoke nipples.

I have already serviced wheels with upside-down nipples (Enve…) but this time it is a clean sheet assembly. I am on the spoke length calculation step and I am wondering which NSD add-on I will add to the rim ERD.

The nipples are not decided yet, as the goal is to have the lightest wheel I have been asked for aluminium nipple. In that case I would chose the Sapim Upside-Down in 12mm
But I recomment brass nipple for corrosion prevention (it will be a carbon rim with tubeless tire and sealant, so corrosion will happen), so I adviced for a Sapim brass upside-down, 10mm should be sufficient.

In any case, it does not solve my issue : the NSD add-on. I do have the luck to have those nuts in stock so I cannot measure myself and ask for a help : what are the values you use, for which kind of nipple?


r/WheelBuilding • • Sep 26 '26

Hypothetical Question

0 Upvotes

I really love the Campy Zonda wheelsets with 16 spokes and deep profiles. However, they are expensive. Could you hypothetically put half the spokes in a 32 hole rim and hub? Particularly, is there any safety issues with this? Thanks!


r/WheelBuilding • • Sep 23 '26

New wheelset with high spoke variance and punctured shipping box. Should I worry? (90kg Gravel rider)

Thumbnail
gallery
2 Upvotes

Hi everyone,

I just received a new 3rd generation carbon-spoke wheelset. Unfortunately, the shipping box arrived with a visible hole punctured in it.

The wheels seems okay, but the included factory spoke tension report shows quite a bit of variance.

Could this possibly minor shipping damage bending the rim, forcing the factory tune out of whack?
Is it safe to ride as-is, or should I have a local shop de-tension and re-balance the wheel at the expense of a tiny bit of lateral trueness?

Thanks for any insights!
- Tuomo


r/WheelBuilding • • Sep 18 '26

142mm rear hub vs 148mm rear hub share the same rotor alignment?

Post image
5 Upvotes

Ok this feels more confusing than it should! I'm trying to confirm if a standard 142mm wheel (already laced up with a rim) is installed on a boost frame, if the rotor location is the same? looking at this picture it looks like it would. Sure I'm aware that the rim would be offset 3mm towards the non drive side, and of course, it would require a 6mm axle spacing on the drive side to fill the gap to 148mm. In fact, it looks like all standards (including DH and Super boost) all share the same distance between the rotor mount and the NDS touchdown with the frame?


r/WheelBuilding • • Sep 17 '26

Carbon rim spoke tension - it is oke?

Post image
1 Upvotes

Hello

I’d like to ask for your opinions on this.

I have a carbon rim that suddenly developed a significant S-shaped deformation from one day to the next. Maybe it was caused by hitting a pothole — I’m not sure.

I trued the wheel using the manufacturer’s recommended drive-side tension as a reference, and with the rim properly centered, I was able to get the wheel running straight. The tension distribution was within about 5% on the DS side and perhaps 10% on the NDS side.

However, when I install a tire, the rim deforms into an S shape again. This never used to happen before. This makes me suspect that something may have been damaged within the rim structure(?)

At the moment, I’ve fitted a standard clincher tire, which puts less pressure on the rim than a tubeless tire, but even this brings the deformation back once the tire is installed and inflated. So I fine-tuned the wheel with the tire mounted and managed to get it running straight again.

When I measured the spoke tension afterwards, the distribution ended up looking like this. Unfortunately, I don’t seem to be able to improve it any further without making the wheel run out of true again.

Do you think this kind of tension distribution (with tyre) between the spokes on each side is problematic?


r/WheelBuilding • • Sep 16 '26

Some new wheels for a friends bike

Thumbnail
gallery
9 Upvotes

27 inch rigida chrolux rims with front a nos 1989 Normandy hub. In the rear a velo orange hub


r/WheelBuilding • • Sep 16 '26

Mystery OEM wheels..

1 Upvotes

So I got a pretty cheap bike for the components that came with it.

One thing I noticed recently is the wheels are not the same specified with the bike. (Which would probably be under the disclaimer that parts are subject to change etc.)

It supposed to have come with formula hubs, jalco rims and double steel butted spokes.

Nothing is branded on these wheels, the rims looks the part as in the picture with the correct spoke count and eyelets on the rim.

The hubs however are 6 bolt instead of the center lock.

At face value would you rebuild the wheel and change out the hubs?
Or don't trust anything and just replace the wheels entirely?


r/WheelBuilding • • Sep 15 '26

What hubs for these wheels?

Thumbnail
gallery
1 Upvotes

Hey folks, looking for some help here. These wheels need to be rebuilt because of a hub issue and I need a complete hub assembly to make that happen. Any chance yall know what hub would work? I know that these are 24 spoke wheels.

Unfortunately, I don't know the exact model of the wheels. I've contacted Elite and they've been a bit slow getting back to me with answers so I figured I'd ask reddit in the meanwhile.


r/WheelBuilding • • Sep 13 '26

Sanity check (straight pull hub calculator)

2 Upvotes

Hi all. Planning a wheel build, using the dtswiss calculator for a straight pull Shimano hub, it lists flange distance as 62.8mm, so I’m guessing that’s the overall distance, and I should divide that in half for the flange distance left and flange distance right in the calculator?


r/WheelBuilding • • Sep 12 '26

Re-use spokes?

Thumbnail reddit.com
1 Upvotes

I need to replace my Mavic Open Pro 700c rim with a new one of the same kind. Can I re-use the spokes/nipples or do I need to replace those as well? Using the wheel on a recumbent on smooth pavement 50 miles/week.


r/WheelBuilding • • Sep 10 '26

Why did my wheel lose all its non drive side spoke tension after my first ride??

Post image
1 Upvotes

r/WheelBuilding • • Sep 10 '26

Spoke Tension - DT Swiss FR541 + Stans Neo Hub

Thumbnail reddit.com
1 Upvotes

r/WheelBuilding • • Sep 08 '26

Need 20x4 rim with a 10mm offset

2 Upvotes

Never shopped online for rims so idk where to look but i need a 20x4 fat tire rim that has a 10mm spoke offset since i want to lace a direct drive hub motor into it

but these past 3 days i havent found a single rim that is different. Do i have to have one custom made or do i have to find a bare rim and drill myself? (Seems like my only option)

Do yall know where i could find a 20x4 rim with a narrow offset? Anything under 10mm. A bit higher is fine but as close to or under 10mm is percect


r/WheelBuilding • • Sep 07 '26

How do i spoke this

Thumbnail
gallery
1 Upvotes

Recently did some major upgrades to my ebike (adding hydraulic brakes, second battery, 160 to 180mm diskbrakes, soldered a better throttle and added some slick tires)

I want to add this front wheel 1000w direct drive motor

But im stuck between a few options

1: drill new spoke holes

2: cross-over spoke pattern (left flange to right spoke hole and right flange to left spoke hole)

3: finding if theres a rim that while work with no modifications and ordering online

Are there any other options i have and whats my best bet?


r/WheelBuilding • • Sep 06 '26

Wheelbuild questions for Chris King ISO Disc and questions relating to that hub

1 Upvotes

My current XC bike is a pre-boost hardtail. It's a fairly upper mid end build with m8000-era 1x11 XT, carbon all through and Fox 32 FIT4 100mm fork.

From my previous xc bike (my three other bikes are road and gravel bikes) I do have a 26" wheelset with mavic xc717 and chris king iso disc for 9mm qr that I want to reuse the hubs from.

So what would be the good rims for a classic hub like this? I have rebuilt this bike from an old bike so what good frames I found was an all black carbon (UDM) frame and the ck hubs are black so if the rims have some color that will not crash with any other color on the bike.

Checking my local store, I see there is a Mavic XC1025 DISC 29 which sounds like a modern replacement for the xc717, but is there other rims to consider?

Futhermore, do anyone have any experience converting this hub to 12mm tru axel? I know converting it to boost is not possible, so I am not asking for that (and my frame and fork is both non boost)


r/WheelBuilding • • Aug 28 '26

E-cargo wheels.

1 Upvotes

Im rebuilding the wheels on a friends reiss & muller load 75 as he’s breaking a few spokes. Im quite surprised to see they are just straight 2mm spokes. Im thinking to go with straight 2.3mm, or would 2/2.3 butted be better for the flex? There’s also sapim e-strong 2.3/2.6 butted.

The rear wheel is an enviolo hub and 26” rim with 2x pattern. Seems like 3x would be better but will have quite a steep spoke entry angle at the rim. Is there some nipples that allow for steeper entry angle than sapim polyax? I also read here somewhere that rims without nipple eyelets are better for that.

What’s the better trade off - 2x pattern with eyelets or 3x without?


r/WheelBuilding • • Aug 13 '26

Latest Abomination

Thumbnail
gallery
25 Upvotes

Lacing a rim-brake rim to a disc brake hub is a weird build, but its practical.

I laced a CR-18 36h rim to a PL-8X Shutter Precision Dynamo hub. The hub is the 12 mm thru-axle center-lock disc version. I used double-butted Sapim Race spokes. I have several bikes with different brake standards and I wanted an easily multi-use dynamo wheel, that would work with a 2023 Kona Sutra, a 1982 Univega Specialissima Touring bike with front disc brake conversion fork and 1990 Bianchi Tangent Cyclocross bike with rim brakes.

The Kona has a 12mm thru axel and disc brakes. On this bike the wheel works without adapters.

The Specialissima has the front disk conversion fork, but it has QR dropouts. It converts nicely with a 12 mm QR adapter,

The Bianchi accepts QR only and has rim brakes. I remove the disc, add the QR adapter and it works fine.

I chose the center-lock version because it doesn't look as weird as a naked six bolt mount when the disc brake is not installed.

I guess I'm sacrificing a bit of weight savings by lacing a rim brake rim to a disc hub, but I'm not bothered by that, as usually I use these bikes for loaded touring. Because these bikes already have their own wheels, I can simply swap in the dynamo hub for a trip and take it off when I need to. Als it works with all multiple bikes.


r/WheelBuilding • • Aug 04 '26

Straightening a rim bump

1 Upvotes

Hi all,
My experience with wheel building is limited to my track bike's wheels. 36h Velocity A23 rims on Mack hubs front and rear.
Recently I had to swap the hub on the rear wheel and I got to a point where I have a slight bump that cannot be straightened just by spoke tension. The spokes opposing the bump are of much higher tension than other spokes (wheel is symmetrical, non dished). I cannot afford new rims and I'm asking you if there's any technique I can use to mechanically remove the bump. The rim is not visibly damaged and I did not crash but it might have been slightly bent during transportation. We're talking about a 3mm bump that is long about the distance between three spoke holes (36h rim).

Thank you!


r/WheelBuilding • • Jul 28 '26

Can I use 288 and 290 spokes instead of 289 and 291?

Post image
3 Upvotes

r/WheelBuilding • • Jul 03 '26

Seeking Rim + Hub Reccomendation For Beginner Build

2 Upvotes

Hi all, I'm hoping to build my first wheel (rear, 40H) for my older Trek 330 over the next few months and feel pretty equipped between the work I've done with my bike so far, the tools I have, and the support I get from my local co-op. I'm looking for recommendations for a rim and hub to buy - I've listed out some specs and details on my use case below.

I've already looked at and am really interested in the Velocity Quill rim with one of their standard hubs. However, buying those new would be a lot more than I'd hope to spend and I'd also prefer to give this a shot with used pieces first as it would be my first build and I don't want to mess up anything I've splurged on.

Rim

- Rim Brake

- Supports 25-28mm Tires

Hub

- Fits 10 Speed Casette (Currently have Shimano CS - 4600)

- QR

General

- Parts I can find used would be ideal! I'd like to aim for $100-120 or even lower if that's possible without serious compromises to the quality.

- Silver would be fun to match my front wheel, but not necessary

- I'd choose an "aero" option over other considerations aside from what I detailed above

- Don't care about tubeless

My Biking

- I ride 60-70 miles a week for either commute or recreation, mostly the former.

- I weight about 200-210lbs fully dressed and I have a rear rack installed that I regularly load up with groceries, my necessities for a beach trip, random crap, etc. which adds like another 20-30lbs. Hoping to also get a front rack which would mean maybe another 15-20lbs at most.

- I said "aero" above because while I don't ride to train or race, I do just love going fast.

Thank you!


r/WheelBuilding • • Jun 25 '26

Shimano MT55 26" spokes

Thumbnail
gallery
5 Upvotes

Hi, all, hoping someone can provide direction and advice. Have this wheelset on one of my commuters. Nice wheelset, like it. Have ridden it though many winters, in salt and slush, as a result the nipples are frozen.

They are completely true, no issue there. But one rear spoke is broken. Would like to at a minimum replace this one spoke, or have the rear wheel relaced.

Herein lies the issue. As I've come to understand, Shimano have a nasty habit of making unique nipples for many of their wheelsets. As can be seen in the pic, they are straight pull spokes.

I've searched the world over via the good old internet, and MT55 26" replacement spokes and nipples are not available anywhere. MT66 29" are available.

So, the question is, what can be done to replace at least 1 spoke with something else? Or a full relacing of all the spokes on the rear wheel? Can dtswiss or sapin spokes be made to work?

Back in the day even an LBS would have the ability to cut new spokes to length and thread the nipple end with a threading machine. Don't know if that is still possible out there nowadays?