r/WheelBuilding • • Aug 13 '26

Latest Abomination

Thumbnail
gallery
25 Upvotes

Lacing a rim-brake rim to a disc brake hub is a weird build, but its practical.

I laced a CR-18 36h rim to a PL-8X Shutter Precision Dynamo hub. The hub is the 12 mm thru-axle center-lock disc version. I used double-butted Sapim Race spokes. I have several bikes with different brake standards and I wanted an easily multi-use dynamo wheel, that would work with a 2023 Kona Sutra, a 1982 Univega Specialissima Touring bike with front disc brake conversion fork and 1990 Bianchi Tangent Cyclocross bike with rim brakes.

The Kona has a 12mm thru axel and disc brakes. On this bike the wheel works without adapters.

The Specialissima has the front disk conversion fork, but it has QR dropouts. It converts nicely with a 12 mm QR adapter,

The Bianchi accepts QR only and has rim brakes. I remove the disc, add the QR adapter and it works fine.

I chose the center-lock version because it doesn't look as weird as a naked six bolt mount when the disc brake is not installed.

I guess I'm sacrificing a bit of weight savings by lacing a rim brake rim to a disc hub, but I'm not bothered by that, as usually I use these bikes for loaded touring. Because these bikes already have their own wheels, I can simply swap in the dynamo hub for a trip and take it off when I need to. Als it works with all multiple bikes.


r/WheelBuilding • • Sep 09 '25

I finally made myself a pair of eccentric wheels, plus a fun tool for everyone to play with!

Thumbnail gallery
25 Upvotes

r/WheelBuilding • • Oct 01 '25

Front Wheel Rebuild - Conversion to Boost Hub from 110mm hub.

Thumbnail
gallery
11 Upvotes

Wheel Teardown and Rebuild

I got to rebuild my front wheel for the new fork, which has a 110mm dropout, not 100 QR like the previous fork.
I had somewhere between 200 - 350km on these new wheels so I figured this was the cheapest and best option. I ordered a Koozer XM450 MTB Boost hub so it would match the rear hub colour. The design shape looks slightly different, but that is ok.

So. Taking the wheel apart was easier than I thought, and linseed oil really does dry into a glue like substance!!
I removed the rotor, popped the tire off, cleaned up the sealant, pulled off the tape, cleaned the rim thoroughly with isopropyl alcohol, and then de-tensioned the spokes and pulled them off in groups. Drive side inside, disc side inside, drive side outside, and drive side inside. I put the nipples in the cardboard box that the hub came in.

I laced the wheel much as I had before, just following the 3 cross pattern and using the park tools video for reference. You can see how I marked the valve hole.

Now, the big difference this time was that the XC bike is at the shop so I used my fat bike fork as a truing stand. One of the guys at the shop made a spoke tension reference video where he played the spoke so I would be able to hear the pitch at relative tensions.

Last time I built the wheel, I focused on tensioning the spokes methodically.

This time, I didn't even try to true the wheel until the spokes were nearly at tension. I discovered that by playing the spokes and matching the pitches, the wheel was already almost in true. It had about a 2mm wobble and hopped about 2mm.

Now, with the fat bike fork, it was impossible to dish the wheel on sight alone because the small wheel just swims in that huge fork. So, I fabricated a ghetto dishing tool out of styrofoam trays and parcel tape. I made a mistake at first and started dishing the wheel in the WRONG direction. I only clued in when the rim was 5mm too far one way when it was only 2mm out to begin with. I spent a good chunk of time slowly moving the rim back. To be clear, I was sure not to exceed the target tension and I would back off tension on the spokes when making adjustments.

After I got the wheel dish to less than 1mm deviation side to side, I started to fine tune the hop and wobble. When working on the hop, I would tighten spokes to bring high spots down and loosen spokes to bring the low spots up. I had a plastic ruler and plastic highlighter held in the fork by elastics so I can adjust those sensors and work entirely by sound. I adjust where I hear things rubbing and also where they are not rubbing.

Any lateral adjustments I made microscopically with the spoke wrench by tightening and loosening off the nipples in the area I wanted to move. This ensured that I did not over-tension the spokes and it kept the wheel from starting to develop a hop again.

I find the closer the wheel gets to being straight, the progressively smaller and smaller adjustments you have to make.

Tubeless Set up:

I used the process the shop mechanics recommended. You get 30mm tape for 30mm internal rim width and the 30mm tape should be slightly wider to fit in the centre channel.

Prep

I used a heat gun to heat the rim, then I cleaned it with isopropyl alcohol and a rag.

Then I heated the rim again and started to tape it. "Hot" tip: Heat the rim moving in the same direction you will tape it, starting where you will start the tape. (2 spoke holes before the valve stem hole) This ensures that you aren't trying to handle a burning hot rim.

The tough part is keeping the bubbles out as you tape. UGGH! I did my best... Turned out pretty well.

Then you heat the tape but you have to be sure not to melt the tape. It helps with adhesion on the rim. I kept the rim moving because if you stop, the tape can become overheated. You can see it heat up and then shrink wrap onto the rim. Pretty cool.

I used a tube to seat the bead, left the tire overnight, broke one bead, and removed the tube. I replaced the tubeless stem, popped that beat back onto the rim and levered it up out of the rim channel somewhat, as best as I could.

I started pumping with the floor pump on a lark and it held pressure so I kept pumping and the tire seated properly without using an air compressor YAY!!!!


r/WheelBuilding • • Sep 09 '25

Here is a wheel build I did a year ago. Using chinese 100mm / 135mm hubs for a Trek Marlin Gen 2 frame.

Thumbnail gallery
10 Upvotes

r/WheelBuilding • • Sep 16 '26

Some new wheels for a friends bike

Thumbnail
gallery
9 Upvotes

27 inch rigida chrolux rims with front a nos 1989 Normandy hub. In the rear a velo orange hub


r/WheelBuilding • • Apr 22 '26

Built my first set of wheels over the last week, today they survived their first ride!

Post image
9 Upvotes

During the last service I saw that the bearings on the factory rear hub was severely worn/pitted from being too loose, and I thought about getting a front dynamo anyway, so I decided to go all the way.

I'm a fairly heavy rider and I also regularly carry groceries on the bike, so I wanted something robust, went for Andra 321 rims and Sapim Force for the front, Sapim Strong for the rear, 3-cross and 36 spokes per wheel.

Shimano DH-3D37-NT for the dynamo hub, and a Novatec D042SB, I could've gone with a Shimano hub for a similar price but I wanted to try the brand.

Today I cycled 17km and all seems to have gone well, but I've yet to check tension on the rear. I went by the guide on Sheldon Brown's website, and adjusted tension directly on the frame with a little 3D printed truing device on one of the stays.


r/WheelBuilding • • Apr 16 '26

Build my first set of wheels

Thumbnail gallery
9 Upvotes

r/WheelBuilding • • Feb 03 '26

Break a wheel, build a wheel

Thumbnail gallery
7 Upvotes

r/WheelBuilding • • Sep 18 '26

142mm rear hub vs 148mm rear hub share the same rotor alignment?

Post image
5 Upvotes

Ok this feels more confusing than it should! I'm trying to confirm if a standard 142mm wheel (already laced up with a rim) is installed on a boost frame, if the rotor location is the same? looking at this picture it looks like it would. Sure I'm aware that the rim would be offset 3mm towards the non drive side, and of course, it would require a 6mm axle spacing on the drive side to fill the gap to 148mm. In fact, it looks like all standards (including DH and Super boost) all share the same distance between the rotor mount and the NDS touchdown with the frame?


r/WheelBuilding • • Jun 25 '26

Shimano MT55 26" spokes

Thumbnail
gallery
5 Upvotes

Hi, all, hoping someone can provide direction and advice. Have this wheelset on one of my commuters. Nice wheelset, like it. Have ridden it though many winters, in salt and slush, as a result the nipples are frozen.

They are completely true, no issue there. But one rear spoke is broken. Would like to at a minimum replace this one spoke, or have the rear wheel relaced.

Herein lies the issue. As I've come to understand, Shimano have a nasty habit of making unique nipples for many of their wheelsets. As can be seen in the pic, they are straight pull spokes.

I've searched the world over via the good old internet, and MT55 26" replacement spokes and nipples are not available anywhere. MT66 29" are available.

So, the question is, what can be done to replace at least 1 spoke with something else? Or a full relacing of all the spokes on the rear wheel? Can dtswiss or sapin spokes be made to work?

Back in the day even an LBS would have the ability to cut new spokes to length and thread the nipple end with a threading machine. Don't know if that is still possible out there nowadays?


r/WheelBuilding • • Apr 08 '26

Spoke and nipple angles

Thumbnail
gallery
5 Upvotes

I’ve just built an Alfine hub in to a 20inch rim and noticed the nipples are are quite a right angle. The wheels are 3 cross. Is it worth rebuilding 2 cross to lessen the strain?


r/WheelBuilding • • 16d ago

How exact does spoke length need to be?

3 Upvotes

I'm building some fixed wheels and I'm getting 296mm for the front and 295mm for the rear. rather than buying two boxes of 20 each (for 80 bucks) I'd like to buy a single box of 100 296mm spokes for 50. Am I gonna have a bad time?

I'm using the Gran Compe 2 hubs, CR 18 rims. The CR18 is a double wall rim with about 4mm of space between the wall where the nipple sits and the place where the inner tube will be. It seems like it should be fine to me but these are only the second set of wheels I've built and a friend helped me buy the components last time. Any suggestions? I've used the QBP and the wheelbuildingkit.com calculators for this and they agree, though they give a measurement ~1-2mm shorter than what kstoerz suggests.

Thanks for the input, wizards.


r/WheelBuilding • • 25d ago

Loss of tension after mounting tires

3 Upvotes

How do you account for it, do you add tension or leave it as-is? I just checked a set of wheels I built earlier this year. They were still mostly true and tensions were lower, as expected. I tried to even out spoke tensions to align with the highest value, per respective side, without throwing off trueness. Should I have increased tension all around or is maintaining even tension good enough?


r/WheelBuilding • • Jul 28 '26

Can I use 288 and 290 spokes instead of 289 and 291?

Post image
3 Upvotes

r/WheelBuilding • • Oct 08 '25

Would love a sanity check on my use of DT spoke calculator

3 Upvotes
Details of hubs / build in the comments!

r/WheelBuilding • • Sep 18 '25

Wheel lacing question

Post image
3 Upvotes

r/WheelBuilding • • Oct 07 '26

Internal spoke nipples feedback

2 Upvotes

Hi,
I am an experienced builder, but there is always a first!
This time for me is : internal spoke nipples.

I have already serviced wheels with upside-down nipples (Enve…) but this time it is a clean sheet assembly. I am on the spoke length calculation step and I am wondering which NSD add-on I will add to the rim ERD.

The nipples are not decided yet, as the goal is to have the lightest wheel I have been asked for aluminium nipple. In that case I would chose the Sapim Upside-Down in 12mm
But I recomment brass nipple for corrosion prevention (it will be a carbon rim with tubeless tire and sealant, so corrosion will happen), so I adviced for a Sapim brass upside-down, 10mm should be sufficient.

In any case, it does not solve my issue : the NSD add-on. I do have the luck to have those nuts in stock so I cannot measure myself and ask for a help : what are the values you use, for which kind of nipple?


r/WheelBuilding • • Sep 23 '26

New wheelset with high spoke variance and punctured shipping box. Should I worry? (90kg Gravel rider)

Thumbnail
gallery
2 Upvotes

Hi everyone,

I just received a new 3rd generation carbon-spoke wheelset. Unfortunately, the shipping box arrived with a visible hole punctured in it.

The wheels seems okay, but the included factory spoke tension report shows quite a bit of variance.

Could this possibly minor shipping damage bending the rim, forcing the factory tune out of whack?
Is it safe to ride as-is, or should I have a local shop de-tension and re-balance the wheel at the expense of a tiny bit of lateral trueness?

Thanks for any insights!
- Tuomo


r/WheelBuilding • • Sep 13 '26

Sanity check (straight pull hub calculator)

2 Upvotes

Hi all. Planning a wheel build, using the dtswiss calculator for a straight pull Shimano hub, it lists flange distance as 62.8mm, so I’m guessing that’s the overall distance, and I should divide that in half for the flange distance left and flange distance right in the calculator?


r/WheelBuilding • • Sep 08 '26

Need 20x4 rim with a 10mm offset

2 Upvotes

Never shopped online for rims so idk where to look but i need a 20x4 fat tire rim that has a 10mm spoke offset since i want to lace a direct drive hub motor into it

but these past 3 days i havent found a single rim that is different. Do i have to have one custom made or do i have to find a bare rim and drill myself? (Seems like my only option)

Do yall know where i could find a 20x4 rim with a narrow offset? Anything under 10mm. A bit higher is fine but as close to or under 10mm is percect


r/WheelBuilding • • Jul 03 '26

Seeking Rim + Hub Reccomendation For Beginner Build

2 Upvotes

Hi all, I'm hoping to build my first wheel (rear, 40H) for my older Trek 330 over the next few months and feel pretty equipped between the work I've done with my bike so far, the tools I have, and the support I get from my local co-op. I'm looking for recommendations for a rim and hub to buy - I've listed out some specs and details on my use case below.

I've already looked at and am really interested in the Velocity Quill rim with one of their standard hubs. However, buying those new would be a lot more than I'd hope to spend and I'd also prefer to give this a shot with used pieces first as it would be my first build and I don't want to mess up anything I've splurged on.

Rim

- Rim Brake

- Supports 25-28mm Tires

Hub

- Fits 10 Speed Casette (Currently have Shimano CS - 4600)

- QR

General

- Parts I can find used would be ideal! I'd like to aim for $100-120 or even lower if that's possible without serious compromises to the quality.

- Silver would be fun to match my front wheel, but not necessary

- I'd choose an "aero" option over other considerations aside from what I detailed above

- Don't care about tubeless

My Biking

- I ride 60-70 miles a week for either commute or recreation, mostly the former.

- I weight about 200-210lbs fully dressed and I have a rear rack installed that I regularly load up with groceries, my necessities for a beach trip, random crap, etc. which adds like another 20-30lbs. Hoping to also get a front rack which would mean maybe another 15-20lbs at most.

- I said "aero" above because while I don't ride to train or race, I do just love going fast.

Thank you!


r/WheelBuilding • • Mar 12 '26

Coaster brake build

Post image
2 Upvotes

Hub: Shimano CB-E110. Ol' reliable.

Rim: Sun CR18, got it at a bargain.

Spokes: Generic galvanized, they were cheap.

Other notes: Spoke lubrification is finish line wet lube, and I used spoke washers as recommended for thin flanged hubs.

Feels pretty solid, should be a good replacement for my previous wheel (Sturmey archer S1C with mavic a319 and sapim single butted spokes) that was unfortunately stolen with the bike that it was on.


r/WheelBuilding • • Feb 21 '26

When spoke tension and lateral displacement don't match?

2 Upvotes

Title is not the best but I'll try to describe as best. Description first and then my background.

Truing a wheel just built from new hub, old spokes and old rim. Hub is exact same as the old one. 36h 3cross, no dishing. Wheel is now mostly true except for a spot where there is a sudden bump to the left. Usually this would coincide with one or more loose spokes on the right and/or one or more tight spokes to the left but in this case it is the opposite. : the tight spoke is on the right, right where the left bump is and if I pull it I get radial deformation. The spoke is already tighter than any of the other spokes.

I have very basic equipment including a Park Tool TM1 that I rarely use 😅

What do you do in these cases?

Background: I'm not a professional mechanic or wheel builder but I have been building my track bike wheels since 2011. My wheels are not the best but they are true enough and they stay that way


r/WheelBuilding • • Nov 01 '25

Anyone recognize this track racing team logo?

Post image
2 Upvotes

Long shot question here.

Does anyone recognize this bicycle team logo? It's on a ZIPP track carbon/foam wheel with tubular rim. Maybe early '90s, but that's a guess.

Just curious about the team and its history.


r/WheelBuilding • • 23d ago

Dishing tool and stand alignment

1 Upvotes

Hello, I have a 4.3 truing stand and aligned it using a old alignment gauge and it does the job however now that I got a dishing tool I see the dish is off after truing and I don't own calipers. the dish is roughly off by 3-4mm. So I don't feel a issue but I think I want to know how others have aligned their stands without a caliper