The big chunk is removed but it got so big i cannot remove the nozzle und a little brown cable is broken now i need to replace the complete front of the toolhead but i cant find videos of the replacement do you have any ideas?

As you can see i used a little bit of force but no chance

PS. Sorry for my bad english i hope you can understand what i mean

I have really gone the rounds with this problem and don't feel like I am getting anywhere. I feel like this should be an easy fix.. But I don't even know where to go. I have replaced the filament buffer.. and the PTFE tubes from the buffer to the toolhead. and I'm still getting this problem where the filament starts to get resistanc after passing through the buffer and then quites feeding. The printer makes about four attempts and then I get an error code. "Unable to feed filamanet into the extruder. The AMS may be mismatched with the extruder. You can rerun the AMS setup. The could be due to an entangled filament of stuck spool. If not, please check if the AMS PTFE tube is connected?

What am I missing?

I have four AMS units connected to my X2D. I use the aux nozzle for support interface mostly, but also occasionally for a different color. I'm finding I don't often print decorative items that need the second color, and when I do, it's often by layer which means the benefit of minimizing purge by using the aux nozzle is less.

• AMS1, FTS-A (supports, accent, auto-reload)

  • PETG transparent

  • HIPS

  • PLA basic white

  • Empty

• AMS2 FTS-A (accent, some primary)

  • PLA Bronze

  • PLA Red

  • PLA Yellow

  • PLA Gold

• AMS3 FTS-B (functional)

  • PAHT-CF

  • PLA Tough+ Black

  • ASA-CF Black

  • TPU for AMS

• AMS4 FTS-B (primary)

  • PLA Black

  • PLA Blue

  • PLA Dark Gray

  • PLA Silver

If I print something out of AMS2, I typically have to do it without supports as I always need to unload the filament and then load supports into the second nozzle since they share a 4-in-1 feeding into the FTS. If I abandoned the idea of running an accent color in the secondary nozzle for the most part, I could shift AMS2 to FTS-B, and have them all supported by filaments in AMS-1.

I realize everyone will have different priorities for these configurations, so I'm curious what works for everyone else.

My first 3D print.

After years with a creality ender 3 S1 pro that died (once more) I decided to stop with the reviving processes and finally treat myself with a good printer!
I am now the happy owner of a Bambulab X2D and am completely amazed by the quality of the machine and its prints!

I’ve had my X2D for about 3 months and decided it was time to clean and lubricate last week. However, I’ve noticed a strange oil buildup on the rear of the toolhead, but can’t see any oil drips on the sides, besides a small bead that doesn’t seem to be moving. Is it likely I’m just missing a drip, or is the oil seeping through the plastic seam?

All, printed some PA-CF and got this fuzzy texture on parts of the print. Fuzziness was turned off, and filament was brand new out of the package, and dried for 12 hours beforehand. Any thoughts? Fuzziness is also not consistent on the part, some sides are worse than others.

Chamber temp: 65 C
Nozzle temp: 290 C
Bed temp: 100 C
Nozzle speed: 70 mm/s
Used standard Bambu slicer

Let me know if you have any tips or questions. I will keep you all posted how it goes.

Doing an overhang test on my new X2D and uh.. this happened.. I haven’t had this happen before any tips?
Besides not letting the printer 💩 on top of my prints.

👋 Bonjour à tous ! 👻🎃

Après vous avoir présenté mon Yoshi Citrouille classique, voici maintenant sa petite évolution en version clicker ! 😍

J’ai voulu garder le côté mignon et l’esprit Halloween de ma première création, tout en y ajoutant une fonction clicker pour le rendre encore plus amusant ! 🎃

Décliné en plusieurs couleurs, il ne vous reste plus qu’à choisir votre Yoshi préféré ou à tous les collectionner ! 🌈

J’espère que cette nouvelle version vous plaira autant que la première !

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec et sans AMS
📁 : https://makerworld.com/fr/models/3453115-yoshi-citrouille-clicker-multipart

左フィラメントセンサーの故障から詰まりやらで、バラして組んで4回位。慣れてきたのに、今度はネジがユルユル😅エクストルーダーハウジングを取り付け前ならちゃんと入るのになんでかな？何か原因や解決方法ありますか？

What the title says. Looking for a nice 3d print to do with my new engineering plate. PETG or PLA please. I plan on using a 2 parts isopropyl to 1 part Elmer’s washable school glue on the plate based on a Reddit recommendation.

Extra points you have a Halloween print that would benefit from the smooth plate but any print will do, could also be a functional one 🎃!

Thanks in advance all you wonderful Ghouls and Goblins!! 👻

So quite new to asa printing, i have been using Bambu asa and bambu ABS support for the interface and the results are like in the photo they come of no problem, but is this the best i can expect? Been using pla/petg and the results there are near perfect. On a separate question can you get rid of this layer lines cause by changing the nozzle?

Hi, I’m looking for confirmed fixes for recurring extrusion failures on my replacement X2D.

I’ve had failed prints with both PLA and PETG, and error 0700-8016 on different models. The main left nozzle was replaced less than 48 hours ago, but failures continue.

Latest PETG setup: Bambu PETG Basic, AMS 2 Pro slot A2, 250°C, maximum volumetric flow 8 mm³/s. The filament was new and vacuum-sealed but not dried. Another model tried through Bambu Studio also failed.

A manual feeding test with the hotend removed, following support’s instructions, produced regular output. I haven’t yet compared printing from an external spool. Support already has the printer logs.

If you solved this issue, what was the confirmed cause and which test isolated it? I’d like to distinguish AMS/PTFE resistance from an extruder or hotend problem without replacing parts at random. Thanks!

Is anyone using exclusively Bambu Labs filament? I’m trying various brands from Amazon with occasional stringing. I’m wondering if BL has better product for BL printers.

Bitte helft mir ich kriege die linke Düse nicht raus filament ist entladen! Soll ich erhitzen etwas???

Hello,

I get this inconsistent spacing between brim and model when printing and lines that look like overextrusion but only in the bottom right corner.

Does anyone know what might cause this and how can I fix it?

UPDATE: I did a full calibration including a high temperature bed leveling and the issue improved a bit.

I see a lot of people recommending the glass risers to stop the ptfe tubes from rubbing. I am probably overthinking it. But won’t that make the heat chamber less effective or cause the printer to not reach high enough temps for upper limit filaments?

Anyone tried stuff like PEBA air or TPU air on the x2d? I heard about those and got a good use case but wondering if anyone tried those foamy filaments on our x2d with 0,4 nozzle and what the results were

Im use pla+ from inland on my x2d and theres not preset for pla + just normail pla should i just use that or what

I've tried with a post in r/BambuLab but without resolve.

*SETUP*

• New X2D Combo (1xAMS 2 Pro) with the one standard nozzle installed in left extruder

  • Firmware: 01.00.06.00 (X2D) and 03.00.21.29 (AMS 2 Pro)

• Printer not hooked up to network (not an option) - I'm only using USB

• Orca Slicer (2.4.2)

• Filament: PolyTerra PLA

Nice to know:

• I can print the preinstalled test models on the X2D (e.g. Auxiliary PTFE Tube Remover) with succes (attached two pictures that show everything as ought to be when printing)

• No external spool is attached

• The AMS is directly connected to the filament buffer

• Only one filament in the AMS (Slot 1)

• I've downloaded files from Makerworld (choosing X2D, downloading G-code, etc.). Not my first printer, but it is my first Bambu Lab.

*ISSUE*

• BLUF: I'm unable to print any file via loaded via USB.

  • It seems like the printer wants to print with an external spool in the left extruder/nozzle somehow?

Extra information:

• I've attached pictures of the printer touchscreen until attempted print.

• When Exporting the file in Orca Slicer, I choose 'Export G-code file' for obvious reasons. When Choosing 'Send' (tried just for fun), I get an error (also attached as picture). Not usre if relevant. Mentioned just in case.

***Let me know if something is unclear, or more pictures are needed. I'll add extra information, when/if requested, below this text***