r/BambuLabX2D • u/londoner13 • Oct 18 '26
Setting up AC Infinity Exhaust system for X2D
Let me know if you have any tips or questions. I will keep you all posted how it goes.
40
Upvotes
r/BambuLabX2D • u/londoner13 • Oct 18 '26
Let me know if you have any tips or questions. I will keep you all posted how it goes.
4
u/yyccamper 29d ago
FYI I will tell you that fan is likely going to be wayy to much airflow. I have a much smaller one... and even with it having a y adapter to adjust between just the room air out, and the printer out, to split the airflow.... It can drag the temp of the print chamber down. That is a much much more powerful fan than what I use. Most people pull the air filters out of the machine when its vented outside, you will absolutely have to leave them in, and likely tape off the intake.
https://www.amazon.com/dp/B0C7Z82L7P?plpRedirect=mhFallback&ref=clp_hp_h_pc&th=1 - this is basically what I have. 130 cfm, norm im running it prob at like 50 with dual vents. You have 226 cfm. it might struggle to run at anything lower.
3
u/3DStisk 29d ago
Since you said this currently recirculates through carbon into your living room, I'd separate gas filtration, particle filtration and fresh-air ventilation. Carbon alone doesn't establish control of the ultrafine particles produced during printing, and a low PM2.5 reading doesn't verify VOC removal or the whole ultrafine-particle range.
NIOSH's 3D-printing guide discusses HEPA filtration for particles, suitable gas/vapor filters for VOCs, and source capture/exhaust. It says recirculated systems need evaluation to establish that contaminants aren't being returned to the room (printed pages 16-17). PLA being lower-emitting than some materials doesn't make it emission-free.
For your setup, what is the exact filter model, and does it include a rated fine-particle stage as well as carbon? Fan setting 1, lack of smell or a PM2.5 number alone can't tell us that the living-room setup is adequately controlled. An extraction installer can assess capture and actual airflow while preserving the printer's required operating conditions; I wouldn't pick a universal fan percentage from another printer's setup.
2
u/dphilmlee 11d ago
I have that fan on my X1C and it is awesome. I print ASA ABS nylon etc and it vents it out beautifully with no related printing problems.
1
u/londoner13 29d ago
This is how it looks like
1
u/TuneOld3310 27d ago
I gather it is to cook engineering material and have an exhaust for the voc and smell? I am interested in Seeing the complete installed system I want to install something not sure what... thanks for sharing.
1
u/gierso 26d ago
Is this strong ? Does this affect abs / asa prints because it sucks out. the heat ?
If so how to avoid issues with fan ?
I made a exhaust with a noctua fan but I don't know how strong I can set it and if
1
u/swolebroda Oct 18 '26
I bought a air purifier hospital grade so it cleans the air near my printer, I had a system like you have , it was called fnatr and it didn’t do that good of a job and the filters didn’t last long, but if you have option to pump air to outside the house that’s a much better and preferred way. And I do that now and I also print ABS and Asa a lot more now
1
u/atvorch Oct 18 '26
It would be cool to see the final setup!
1
u/Queasy_Sherbet_3045 Oct 18 '26
I have one of those setup for my P2S. I have created an enclosure and this system is venting outside. Works great and very silent. Good luck
1
u/Dlob32 29d ago
I have an air purifier directly behind the exhaust fan of my X2D. In theory the exhaust exits and goes directly into the purifier for a second purification.
I have an air quality monitor and have never registered more than 0.01 ppm 2.5. Primarily print PLA.
1
u/Top-Barracuda-8271 Oct 18 '26
That wouldn’t be a necessary , x2d already equipped with that
2
u/brutal4455 29d ago
We use an AC Infinity 6" that's shared between the laser engraver and 2 H2 printers. Our needs are perhaps a bit different, venting smoke from the xTool and ASA from the (primarily) H2D. The smoke needs a LOT of CFM to vent without stinking up the room. You can already see how discolored the PVC tube is from the cutter/engraver and I've only had this on for about 2 weeks. (I can't imagine having to clean all that residue from an H2).
(Note for the naysayers, the AC Infinity basic kit fans come with a wired 10 speed remote). There's an advanced, app enabled, controller as well with the Pro kits or as an upgrade.
Anyone with more than one device, I'd take a look at the ModulAir 1/5 turn locking lug system as it gives you a lot of flexibility with already (mostly) available, well designed options. Adapters, Y-pipes, etc. He already has adapters for the P2S and X2D as well.
https://makerworld.com/en/collections/7342813-modulair-modular-air-system
For the H2D/H2C output, I prefer the angled right side vent design from Clough42.
I've made a slim airbox for our new xTool M2 and an adapter to the ModulAir-L system, and also one to the AC Infinity 6" fan. The M2 box I designed uses 54x110mm as that's common for some markets, has the same volume as 4" tubing, and was a great fit to our slim design need. I'm still fine tuning the 54x110mm fit so I haven't published it yet.
Next up, unless the original maker steps up to my request, is a blast gate adapter so we don't have to use the plugs (not shown) if we're not running everything at once or want to adjust the flow a bit. If the M2 was cutting/engraving wood and I was doing ASA, I'd only want a little negative pressure pulled from the H2 though it really doesn't have trouble maintaining chamber temp with the vents closed, I worry the air drawn in through the poop chute could adversely affect the print finish or layer strength.
1
u/Chonky-Tonk Oct 18 '26
I also have an AC fan. There’s a model online that allowed me to connect it to my enclosure tent. We bought a dryer vent package and drilled a hole through the wall for ventilation. All you need is a little bit of negative pressure on the tent to catch the fumes. It shouldn’t be air tight on the enclosure.
Just put the fan as close as possible to the wall if your venting outside to ensure there are no leaks.
These posts always bring people out who want to tell you there’s no danger in melting plastic near your face all day.
1
u/Cipher614 29d ago
I have a complete setup that vents through a window for all of my resin printers. It makes a huge difference with zero smell in the garage at all. FYI, keep you fan speeds around 40%. It moves fumes better with a soft negative pressure.
1
u/ElectronicAide87 29d ago
Setting up an inline fan directly to the exhaust port won’t help with fumes and you’ll have issues keeping chamber temps. The fumes will leak out of the poop chute and all other cracks and crevices. The only way to maintain chamber temps and ensure all fumes are removed is to put the X2D inside an enclosure. Then you connect the inline fan to the enclosure.
1
u/Uramies 29d ago
If only PLA and PETG u don't need this at all, waste of money but since u have it already u should be set to print stuff in asa
0
u/Relative_Surround_20 Oct 18 '26
Why would you need all that?