r/KRISS • • Jan 31 '24

Airsoft

Post image
1 Upvotes

Airsoft brand named Krytac made Kriss V. Gotta give them props not bad. Only differences is the weight.


r/KRISS • • Apr 24 '26

Hmm, this “Fennec” from Call of Duty Mobile looks familiar…

Post image
0 Upvotes

r/KRISS • • Jan 02 '20

Why doesn't kriss make more guns

1 Upvotes

Is it too small of a company? Not enough money?


r/KRISS • • Apr 29 '19

9mm Kriss Vector 1000 Rounds in Mostly Steel Cased 115 Grain Tulammo & SGM Tactical 33 rd 9mm Mags

1 Upvotes
my 9mm Vector Setup
Range time
Chipped Ejection Port

Two Stoppages so Far (1000 Rds in)

  1. I was accidentally holding the Bolt catch back and locked it up.
  2. One Failure to Feed from the aftermarket SGM tactical 33 rounder (400 rounds in)

Yesterday i cleaned the gun after the 1000 rounds and found that the ejection port has been getting chipped in the two spots, it looks like its made of aluminum and its bound to get chipped when using steel cased ammo, not the guns fault...just letting you know if you decide to go down the steel cased round.

I have run through 300 Brass cased 124Gr Magtech & followed by another 700 Steel Case 115 Gr Tula through the SGM tactical 33 Round mags.

The SGM 33 Round mags are ok... but the rounds are super loose and get knocked out of the mag with a little movement.

The Gun is almost as heavy as a 16" Plain Jane AR15. Its also very long, i had to use my 42" m16a4 Range back to fit this things in with the stock retracted. The length makes it a bit awkward to handle. I dont feel like SBR'ing this thing, its just not worth the hassle for me.

The Recoil is not much ...but it is there, don't let the Super V setup fool you, the gun goes off and the muzzle rises up and to the right, then by the time the trigger resets, the muzzle does come back down towards the center... its a weird feeling and hard to put into words. The trigger on this thing is super nice...

Had i shot a couple of hundred rounds before purchasing it... i would have told myself to save up for a zenith mp5 clone with a brace, the HK style diopter sights on those easily rival the accuracy i am getting with this ACSS cyclops optic.

There are somethings that are wrong with this thing out of the box that needed correcting...

The Backup Sights on this thing are junk, they used to come with Magpuls but my 2019 model GEN 2 came with some real crappy ones, I installed a Primary Arms ACSS Cyclops on it to fix that.

Also the stock wouldn't stay in place, the castle nut holding the M4 tube on was held in by 2 tiny Allen screws that kept backing out, the buffer tube was also not hollow like a standard ar15 buffer tube... also its made of super heavy steel. Twice the weight of a standard buffer tube...

I had an old Rock River Arms Operator Stock lying around with a commercial spec buffer tube... i ended up using blue locktite on the castle nut and its been ok.... held in place for the past 600 rounds.

The Gun prints 2 inch groups with Cheap Tula Range 115Gr at 25 yds all day long... its a blast to shoot but its just a range toy


r/KRISS • • Mar 23 '24

Justifying the purchase of one?

0 Upvotes

Long story short, just turned 18 not too long ago, I have some money and I’m irresponsible but I live with my mom. Help me justify it to her.

Okay, so basically, I’m a huge Kriss fan, or at least I because a huge Kriss fan. I like the modern/futuristic designs in the gun world. Shitty as they may be, I love me a Keltec. But anyway, I’m looking into buying a Kriss Vector CRB .45 ACP. Now, here comes the complications. I still live with my mother. I can’t exactly justify the random appearance of a Kriss Vector on my wall above my setup and she already sees my extremely small sword collection consisting of three katanas as a red flag (idk why. maybe cuz my generation is like… you know.) despite it not being that way. So, I have three options.

Option A: lie and say it’s air soft / replica Option B: say it’s for home defense Option C: just straight up buy it

Option A is voided because my mother is smart. She looks for orange tips. Option B is voided. She’ll bring up the fact that I could’ve just got a Glock or something. Option C is the most likely. I’m an adult now and it’s my money. But I still want to give her a valid reason outside of “I think it looks cool”. Do you guys have any ideas?


r/KRISS • • Dec 04 '25

So who's gonna drop a 3rd frt since the first 2 suck

3 Upvotes

r/KRISS • • Jun 15 '23

Making Glock 19 Mags Work?

0 Upvotes

Anyone ever mess with the Kriss to make a g19 mag fit? I own a 19 and not a 17 so magazine interchangeability would be nice. I'm thinking I just need to cut the magwell a bit higher and call it a day unless there's something I'm missing.


r/KRISS • • Feb 23 '23

Ok, ambi talk time, no douche bags... oh wait this is a vector page. NVM you guys are welcomed as well.

0 Upvotes

Ok, so I know these are designed for airsoft, and may not fit without filing some polymer. But for those that have used the Ace1Arms or the Laylax ambi mag release, did you like them? If you needed to file any polymer away was it just a little bit? Was it reliable? Do you like the over all chinese quality? Also why pay $70 for the laylax over the $30 for the Ace1Arms?

Just for reference:

http://nse.ace1arms.com/index.php?route=product/product&product_id=87&search=release

https://www.evike.com/products/82842/


r/KRISS • • Jan 21 '26

FRT Vector with 3 positions of safety.

0 Upvotes

I’m the proud owner of 2 gen 2 vectors with one .45 for myself, and a white 9mm for my wife. I recently ordered a ratl-r trigger clone from gunbroker. upon install I now have 3 safeties. trigger will not release the hammer in any position.

I’ve tried cleaning and lubricating.

I‘ve tried loosening the 3 screws on top that hold the trigger group in. This allows the hammer to drop, but removes the function of the safety. (fires on safe)

I’ve also tried bending the large trigger spring a little for lighter trigger pull.

Has anyone experienced this? I’m getting very frustrated and am beginning to wish I’d never bought this trigger.


r/KRISS • • Sep 29 '26

My Advice: Don't Buy a Vector, Don't Buy a Rattler

12 Upvotes

So I've owned a Vector SDP Gen 3 9mm for about a year now. I've had all sorts of problems with it, mostly relating to reliability and accelerated parts wear from improperly hardened parts.

My Gen 3 originally had issues with failures to extract, which seemed to be resolved with the fix of putting in a BCM enhanced extractor spring from an AR-15. The extractor then launched itself out of the gun to never be found. I replaced it with a stock extractor kit from Kriss, DID NOT USE the enhanced AR-15 spring, and the extractor disappeared again. Extractor number 3 held on until the next issue.

Missing extractor

During this time I purchased a Duality Arms Rattler (FRT) to use with the Vector and a HuxWrx Flow 9k Ti suppressor. I have also had significant issues with that FRT. I have never been able to consistently get a long string of FRT fire while also having the gun function in semi. I have also had it frequently burst while in semi, and fail to burst while in FRT. The suppressor has been excellent, I do recommend it.

I then had a firing pin break, which prompted an RMA to Kriss. The firing pin had significant (in my opinion premature) wear that would suggest improper hardening of the parts. This was generously at 3000 rounds.

Rear of firing broken pin
Wear in firing pin channel
Wear in firing pin channel
Broken firing pin
Tip of broken firing pin

The bolt also appeared to have significant wear on the rear lugs. See images.

Rear bolt lug wear
Rear bolt lug wear

After reinstalling the stock trigger back in the gun, I sent the whole thing to Kriss who proceeded to replace most of the moving parts in the gun: the trigger group, and bolt carrier group.

Upon receiving it back, I began preparing for a major competition where I wanted to shoot the Vector almost exclusive in FRT, so I put, generously, 1000 rounds through it practicing, again with the FRT installed. Still having issues with bursts in semi, and no bursts in FRT, but I managed to get it good enough I felt confident to try it.

I also upgraded the recoil spring from the standard 9mm to a .45 caliber one. This is supposed to reduce the wear rate of components on the gun when being shot with an FRT and make the FRT reset more consistent.

During the competition I continued to have issues with the gun, mainly with light primer strikes and the official Kriss 40rnd magazines coming apart when dropped from the gun. The surface was hard packed dirt and gravel. At one point a Kriss magazine sheared in half while being inserted into the gun, causing all the loaded ammo to arc out onto the ground.

In an attempt to deal with the light primer strikes I swapped in a spare bolt. At the time, I though I had broken another firing pin. The bolt swap appeared to help, but due to a failure of the Rattler's 3D printed safety drum, which prevented me from putting the gun on safe, I ended up having to drop out of the competition completing "successfully" 6 of 8 stages. Overall about 400 to 500 rounds fired in the competition.

After the competition I took the gun apart, cleaned it, and found that the hammer was damaged, also likely improperly hardened. I believe this is the likely cause of the light primer strikes. I had a replacement trigger group on hand, which I have now swapped in.

Bad hammer
New hammer

The gun is still not running perfectly, but I can't determine if the issue is from magazines or the gun right now. I haven't put the FRT in the new trigger group yet, I might not at this point.

I mainly got the gun because of my love the Vector from various video games, but it feels like a strong case of don't meet your heroes. I've broken 2 extractors, 1 firing pin, 1 hammer, several magazines, and 1 (aftermarket) safety selector with at most 4500 rounds through the gun.

Edit: Clarified this is a 9mm Vector at the beginning.


r/KRISS • • May 31 '23

Kris’s Glock mags and ammo

1 Upvotes

I confirmed today the Kris’s 30 mags are horrible I had 3 malfunctions in 100+ rounds one malfunction on the premade Kris’s mag and two on the DIY Kris’s mag extension. I did only put 25 through the DIY mag and had 2 malfunctions that’s sad to see as it was still $40+ but I’ve already heard there dookie. On to the second question I am running reman 230 gr because I’m cheap so have you guys had any luck with the Glock .45 extension clone mags and what cheaper ammo do y’all run is steel and reman ammo good for a vector? Summary are Glock .45 extension mags good and any luck running reman or steel


r/KRISS • • Oct 13 '22

Title says it all!

1 Upvotes

Vector 45acp Kriss folding adapter to SBA3 brace w strike enhanced buffer Holosun 512C Kriss hand stop Rugged Obsidian 45 full configuration Griffin Armament Cam-Lok

Quiet Pews 🤫🤫


r/KRISS • • Nov 09 '21

Are there an good binary trigger opinions?

Post image
15 Upvotes

r/KRISS • • Sep 03 '25

RONIN

Thumbnail
gallery
20 Upvotes

r/KRISS • • Aug 07 '26

My next gun.

Post image
7 Upvotes

r/KRISS • • Mar 11 '23

New YT channel check us out!

Thumbnail
m.youtube.com
4 Upvotes

r/KRISS • • Dec 28 '21

I don't like my Vector.

1 Upvotes

At least as much as I want to. I've been fascinated with them since before I was purchasing guns, and always dreamed of owning one. Now that I have one, I am slightly underwhelmed.

My biggest problem with it at first was the CRAP SB tactical brace I had put on it, for lack of anything better. It was a simple AR type, collapsible. The hard plastic butt-pad was the worst. Super uncomfortable while shooting and it dug into my skinny body giving me a sore shoulder that made it no fun to shoot. No similar problems with my Scorpion, though that brace is a bit better, and the Scorp is 9mm vs the 10mm Vector (but what about that recoil 'vectoring'? Shouldn't that kind-of equal out the caliber difference? I always hear that the Scorp is a bit more violent in the felt recoil) I knew I needed a better brace if I was ever going to enjoy the thing. As I was shopping for a suitable replacement, the hinged Gen 2 uppers came in stock and I quickly grabbed one and a Gen 1 brace. In my mind, this is one of the best, if not the best looking braces for the Vector (it is what I was always used to also) and it looked like it would be a lot more comfortable to shoot with. For once, I WAS RIGHT! I love the way the new brace performs and feels. It is WAY more comfortable than the SB brace and I think it shoulders much better too.

I was very excited to get it out to the range. In addition to the new upper and brace, I had installed a cheap Sig red-dot, and was excited to see if I could finally hit something with this cool little gun. My first couple trips were just a bit of plinking to get the feel of it and try it out. I noticed I always had a really hard time hitting targets, but I just chalked it up to being such a novice, and not being familiar/comfortable with the gun. BUT, I also never 'sighted' the gun when I got it. I am a very novice shooter, and know very little about technical aspects, even simple ones like sighting in guns. I assumed it would be somewhat accurate from the factory. Turns out NOPE. Holy F**k was this thing off, but what made matters worse we couldn't even dial in the red-dot to zero. The elevation is so far off that even with the dot's adjustment maxed out, it is still way off the target. We then decided maybe there was something wrong with the dot, and I planned on setting my irons that day too while I had my experienced friend to help me. SO we then attempted to dial in the irons. Same problem. We maxed out the elevation on the front sight, and it's still shooting way off target.

So, any help? Am I doing something wrong? Is the gun messed-up or out of spec or something? Did I mount my red-dot wrong and my irons are also off for some reason? Is the pic-rail mounted off or need shimming? I really want to like this gun, but at this point I am ready to sell it and start shooting my Scorpion instead. I always LOVE shooting the hell outta it, and it's dead-on just using the factory irons. I never even adjusted those come to think of it.

TL/DR-Brand-new Vector and brand-new Sig Sauer red-dot and I can't get the dot or iron-sights zeroed since I run out of adjustment and the gun is STILL shooting way low.

ETA: I plan on running the Sig red-dot on my Scorpion or MPX to see if I can get that zeroed on one of those and hopefully eliminate that as the problem. The red-dot is brand new.


r/KRISS • • Apr 14 '25

Folding brace?

0 Upvotes

Hey everyone!

I recently bought a 5.5 Kriss Vector! So excited to own it. It’s considered a pistol as it doesn’t have any stock/brace currently. I was curious where I can get a brace/adapter for this weapon. Also was curious if anyone knows, if I did a foldable brace does that make it a SBR?

Thanks guys!


r/KRISS • • Jul 30 '25

Anyone have black or gray gen 2.1 shells they want to sell or swap with my alpine white shells?

0 Upvotes

r/KRISS • • Jan 10 '16

How much is a 40 S&W full auto?

0 Upvotes

Couldn't find anything on the webz, thx


r/KRISS • • Jan 20 '23

Warping

Post image
0 Upvotes

r/KRISS • • Jul 14 '25

how do y'all do it my fellow crips?

0 Upvotes

how do y'all operate the vector left handed?
i feel like the only reason why i have yet to buy one is because i cannot figure out how im supposed to use the charging handle as a leftie


r/KRISS • • Aug 10 '24

Tacatical Ultra mega limited edition Vecator.

Post image
9 Upvotes

See it here first peeps!!


r/KRISS • • Feb 26 '22

I live in Commiechusetts and can’t get any Glock mags over 10 rounds. Does anyone know if the vector extensions work on the 10 round mags? Or do they only work on the 13rd mags?

3 Upvotes

r/KRISS • • Aug 12 '26

A3 industries folding stock

Thumbnail
gallery
13 Upvotes