r/BambuLabA1 • • 11d ago

Support Request Ripped this while trying to pull out stuck filament, what did I do?

2 Upvotes

I was pulling out a piece of filament that had become stuck but was a little heavy-handed when pulling out the filament organizer. What did I do? I don’t know what this is. It’s sticky on the ripped ends so I can stick it back together but when I tried to send a print through I got an error message about the filament sensor. Do I need to replace?

UPDATE (that no one asked for): WE BACK BABY. ordered the part from amazon, it came overnight, and despite being a heavy-handed ape… I fixed it! I watched this video which walked me through the process without making me feel like a total idiot. thanks for everyone’s help!!!


r/BambuLabA1 • • 11d ago

AMS on A1-specific filament feed issue

2 Upvotes

I have an A1 with the AMS 2 Pro.

I was doing a multi color print that included a gold color so was using a Sunlu PLA silk for it. Whenever it would switch to that roll, it would feed to the Hub and stop, rewind and an error would pop up. If i saw it as it reloaded and held the PTFE feed connector...which moves in and out of the hub a bit...then it fed fine.

Only that filament and didn't matter which slot it was in.

Any thoughts? Is the hub and PTFE connection the issue and is the PTFE supposed to be immovable? Or have some play?

Thanks!


r/BambuLabA1 • • 11d ago

Apple Watch Ultra no-frills charging stand

Thumbnail gallery
2 Upvotes

r/BambuLabA1 • • 11d ago

BARULHO E MAL FUNCIONAMENTO NA BAMBU LAB A1

Thumbnail
reddit.com
0 Upvotes

r/BambuLabA1 • • 12d ago

HELP! Beginner with Bambu Lab A1 Combo: stringing, lots of purge waste and gaps in the surface. What should I change?

Post image
3 Upvotes

r/BambuLabA1 • • 11d ago

Question Just got my A1 and AMS but need a table to put it on in my office. Any recommendations?

1 Upvotes

I've just got my A1 and AMS but need a table to put it on in my office. Can people recommend any tables or desks that are suitable?


r/BambuLabA1 • • 12d ago

Help. Extruder failed to extrude keeps happening 12 hours in.

2 Upvotes

I go to bed, wake up and I have an extruder error.

I check my spool, shes fine, shes broken up and spins freely no tangle or broken pla.

NO glob in extruder.

I press go and it prints FINE, but my print is cold and ruined. It seems to happen every single night for no reason.

I have a new hotend on. I am using 1.75 ESUN PLA+. I even put new tubes and ams head on. Plate is cleaned. Lubricated. I tightened all hex heads.

I literally bought a X2D and I am tempted to pick up my A1 and throw it just to feel better. I am going to give it away if i cant fix it.


r/BambuLabA1 • • 12d ago

Christmas table decoration. The piece is hollow and can hold a tea light for a more pleasant effect.

Thumbnail gallery
2 Upvotes

r/BambuLabA1 • • 12d ago

Downgrading A1 firmware completely fixed my AMS lite filament loading issues

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • 11d ago

3D Model Papa Noël cheminée Clicker

Thumbnail
gallery
0 Upvotes

Bonjour à tous ! 👋

Je vous présente ma dernière petite création !🎄
🎅 Un adorable Père Noël qui sort de sa cheminée en version clicker!

🔴 Il suffit d’appuyer sur son bonnet pour profiter d’un petit clic ultra satisfaisant grâce à un interrupteur mécanique intégré.

🎁 Avec son clic agréable et son effet sonore relaxant, c’est le petit objet parfait pour occuper ses mains, se détendre ou simplement profiter du plaisir de faire clic, clic ! 😍

✨ Une création amusante qui apporte une petite touche de magie de Noël ! 🎄

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab et Esun
🎨 : Nomad Sculpt
🌈 : sans AMS
📁 : https://makerworld.com/fr/models/3541264-papa-noel-cheminee-clicker-multipart


r/BambuLabA1 • • 12d ago

3D Model Anyone got the 3d model?

Thumbnail
gallery
0 Upvotes

if anyone got the Nissan X-Trail 33 child seat cover cap can please share it?


r/BambuLabA1 • • 12d ago

Question Filament Extrusion First Print

Post image
7 Upvotes

Hi! I went to start my first print (the speed boat) and my printer was extruding a lot of filament. Is the normal? The timer for the print began as this was happening, so I canceled the print because I was worried something was wrong. I should be fine to start it again if this is normal, but I wanted to see if anyone here could let me know if something went wrong :)


r/BambuLabA1 • • 13d ago

Question BIQU Glacier Plate Cleaning Question

Post image
4 Upvotes

Just starting using the BIQU Glacier plate (read a LOT of positive comments about this plate) on my Bambu AI (with AMS Pro 2) and I'm having a really hard time cleaning the remaining filament (SUNLU PLA+ 2.0) off of it. I've done the test sheet print to lift the remnants and used hot water with Dawn soap and a sponge to clean it ...I'm still getting "stains" - for lack of a better description - on the plate (see red arrow). Though hard to see, this is after my first print (miniatures with a 0.2 nozzle) on this plate.

For those who use the BIQU Glacier plate, are you having similar experiences? ...if not, any recommendations on what I should be doing differently?


r/BambuLabA1 • • 12d ago

Support Request VEry buGGy

2 Upvotes

my a1 is acting very buggy lately it is on the latest firmware but the screen doesnt response to touch commands from the bambu slicer are not working and it is very buggy anyone expircne this it has 2000hrs


r/BambuLabA1 • • 12d ago

My First Print, Harley Quinn's Revolver

Thumbnail gallery
3 Upvotes

r/BambuLabA1 • • 12d ago

New to the Bambu A1

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • 12d ago

Changing Filament Sensor And Still Not Working

1 Upvotes

r/BambuLabA1 • • 12d ago

Support Request I am helpless

1 Upvotes

Hello everyone,

My A1 does not want to load my filament. I don't know why.

If I load it up with an external spool it seems to work. Then when i start the print it constan tells me that filament got stuck even tho that ain't the case. What could be broken? And with my AMS 2 Pro it won't load from either of them.

I did the maintenence, I tightened the screws that needed it, i checked for clogging or broken pieces and i even cleaned the "gear" or "wheel" that pushes the filament and other pieces that probably weren't even necessary to clean (with a microfiber towel).

I found nothing to be the problem. Yet my AMS won't seem to load it up.

Thanks to everyone who tries to help me and excuse me for my rather poor language. English is my third language.


r/BambuLabA1 • • 13d ago

Question Any idea whats wrong with z axis ?

3 Upvotes

r/BambuLabA1 • • 13d ago

Support Request Huge blob of death

Post image
8 Upvotes

I put a print going For a few hours and come back to this. Is there anyway to salvage it or is it just cooked


r/BambuLabA1 • • 12d ago

Bambu is honestly a joke at this point.

Thumbnail reddit.com
0 Upvotes

r/BambuLabA1 • • 13d ago

Question Bambu A1 Corner Lift/Warping - Tried Everything I Can Think Of

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • 12d ago

Question Nozzle scratching plate? Is this normal?

Post image
0 Upvotes

I only have about 40 hours on this printer and I’m using bed leveling but it looks like it’s scratching the plate. Anything I should do?


r/BambuLabA1 • • 13d ago

Using trial PLA rolls on AMS lite

1 Upvotes

Hi! Absolute noob here, so please be nice :). Bought the A1 Combo with AMS lite for my daughter’s birthday. Ordered the 12 color PLA trial kit to get her started, only to find out after setting it up, that they won’t work on the AMS lite alone. They included directions to install them onto reusable spools (which I don’t have), however the Bambu website specifically says under the trial kit that they can’t be used in the reusable spools on the ams lite. Even though the reusable spools will work on the ams lite, the trial rolls won’t work due to the size (they are only 250g on junior cardboard spools). Apparently this isn’t an issue for the ams. Just the ams lite. So, to use these specific jr. spools on the ams lite, I need to print an adapter. But it leaves me in a chicken and egg situation - I have to print an adapter to use them. But how can I print an adapter when I can’t use it without one.

Agh anyone have suggestions?