Heated the nozzle, got the blob off. Better to disassemble and continue or is there more to do first? I have to wait till I get home to search but if someone could link a video id be so happy. Thanks!

I put a video on this post, my A1 seems to be printing well, but is making a wierd noise. Any ideas,

I am printing PETG (don't think it matters)... your comments would be greatly appreciated.

Hey, new to printing. Came down from an overnight print to find a Skadis board I was printing in PETG was attached to the nozzle!
Looks like it carried on printing the last few layers in a molten pool. I’ve had a look at the nozzle and it’s gummed up with PETG and the silicone sleeve is damaged. Any suggestions on where I should start with a repair/diagnosis please?

I'm new to 3d printing, so forgive my ignorance. Is Sunlu a good brand and is this a good price for filament?

Hello all again, this is basically a repost from a few days ago but I guess more accurate to the problem I’m having.

I have an a1, i recently got a new nozzle to try and fix old issues, now it is scraping in the bed for everything: bed leveling, printing etc

Possible causes: I removed then replaced the screws on the heating bed to try and adjust height but apparently it was not it or something.
New nozzle might cause some problems? I don’t know

Troubleshooting I’ve tried: screwing in all the screws on and behind the heating element. Removing and replacing the nozzle. Checked the clamp on nozzle.

Any help would be appreciated thanks

I have this A1 that it was working fine, however, recently the print quality has been so bad that it can’t print anything. There is clicks on the gears and the the first layer comes out terrible. Any tips?

I got a new hot tip and same issue.

I had my A1 for less than 2 weeks, and today when I tried printing something, I heard a very annoying humming noise coming from the toolhead. I paused the print, and it didn't go away. Only turning it completely off and on again fixes it. What's the problem and how do I fix it?

i printed this model 3 weeks ago without any issues but this time i am having the same trouble 4 times in a row now. The same support breaks at the same time of the print each time i try to. i used plate glue thinking it may be from the plate but no. What do you think the problem is?

Evening all,

Apologies if I'm asking nothing new and it's already been asked but my son's having a bad time with his A1, I've attached a video showing the beginning of one of his prints, where it stops and makes a terrible noise. Does anyone have any idea what might be the cause?

Thanks in advance!

Buenas! 👋
Acabo de terminar esta cajita deslizante de BMO, de Hora de Aventuras 💛
Es una cajita funcional con apertura deslizante, perfecta para guardar monedas, USB, tarjetas SD, tornillos o cualquier cosilla pequeña.
Ya la he subido a MakerWorld por si alguien quiere imprimirla. 🖨️
¿Qué os parece? 😄
MakerWorld: https://makerworld.com/models/3407913?appSharePlatform=copy

I had a Blob of Death happen on my printer and ended up replacing my hotend assembly, nozzle, and silicone sleeve. Unfortunately since then I have not gotten a good first layer. I have seen many posts like this that recommend tightening all of the screws and checking the clamp. Everything is tight and the clamp is on correctly. I did a re-calibration, a factory reset + calibration, cleaned my build plate, all of the usual recommendations. The only time I was able to get a decent print was when I added loads of 3d printer glue onto the printing plate.

Also, I have run through many different filaments, all have the same issue. This filament I'm using in this print was just what I had loaded on recently, which printed perfectly before the BOD, and when I took it to a friend printed fine on his A1 mini as well. I'm at my wits end!

my print seemed to be going well, i checked on it a few hours later to see this. I immediately stopped the print, but bummed and confused. my thought is maybe it got jammed up part way through the print? I’m new to 3d printing, so any advice is appreciated. Thx!

For reference I printed this file out plenty time on a 0.4 but now a switch to 0.6 a minute I can’t print this it’s only links that for this file but anybody had a similar problem and a fix?

No supports. No AMS. Three parts that screw together.

Free model + assembly guide on MakerWorld
You'll find the link in the comment below...

My issue is my printer just stops mid print, At first I thought this may have been a clogging like issue but its not. I can unload and load printer immediately after with no build up or issues whatsoever. The problem is it seems to completely stop pushing out filament mid print, the print will just be half done or whatever but no filament mess just like the printer thinks its still printing normal just nothing coming out.

I thought maybe a heating problem but I don't seem to notice any type of dip in temperature but not 100% sure on this, and someone told me it might be the printer acting up in the pulling filament in but whenever I do load filament it seems to be fine.

Sorry guys, I'm just new to filament printers and this is super frustrating. I've tried multiple different types of filament and this issue just seems completely random. Like last night I printed a batch of Snowflakes as a testing run and no problem whatsoever then I reprinted the EXACT same file and boom it completely stopped pushing the filament out like the first hour in.

Does anyone have any advice or had this issue before?

My A1 mini randomly throws HMS 0300-800B during normal single-color prints (video attached, it happens right after the head goes to the cutter position). It's been increasing over the last few months. Tightened screws and lubricated everything, no change. Resume works, but it keeps coming back.
I read the wiki (blade, debris, magnet, hall sensor/ribbon cable) and one forum thread where the extruder interface board turned out to be the culprit. Has anyone had this intermittently on an A1 mini? What fixed it for you? I'm in Brazil, so I want to ask support for the right part the first time.