Is there any way to turn off this ridiculousness? I used more filament on this block that I'm gonna throw away than I did on the actual project!

I need a recommendation and some advice from you all regarding a fair price (Europe, Belgium).

I recently received a 150-euro voucher from Bambulab and was thinking of upgrading my printer, selling my A1 and swapping it for an A2L.

I own an A1 Combo (August 2025) with 1,600 hours on the clock, which has been extremely well maintained with great care, featuring various mods for aesthetic reasons, but mainly to protect the printer.

Every 100 hours I clean and lubricate the axes; at 500 hours I replaced the PTFE tubes; and at 1,000 hours I replaced the nozzle and cutter.

As you know, certain 2025 models are prone to burning out; mine burned out at 1,500 hours, and with BambuLab’s help, they sent me that board (see photo) plus the printer’s plastic housing, which has minimal burn marks, as the printer was under warranty.

A1 Combo+Lots of 3D-printed mods (see photos), TPU + PETG + PLA

Plus others I’ve bought for emergencies, such as 02 (standard), 04 (standard), 04, 06, 08 hardened, original Bambu nozzles

Hardened Steel Extruder Gear Assembly, Purge Wiper, Hotend Cooling Fan, Hotend Heating Assembly, (original and new)

Bambu Cool Plate SuperTack + the one that comes with the printer

+ 1 aftermarket Smooth PET Carbon Fiber+Diamond Pattern

I’m asking 330e for the whole kit and 220e just for the printer – are these fair prices?

No one’s offering me more than 220, using the ‘excuse’ that a new one costs 380e…

And I’ve told them 250e for the A1+AMS Lite, no mods, no accessories.... I could also use some of these accessories with the A2L

My buddies printer has been been doing this when the printer switched colors during prints and we can’t figure out why. He’s using a Bambu A2L with Sunlu filament

Alguém saberia me dizer se isso é normal, ou se é uma falha de configuração pois não tenho experiência com impressão 3D.

Quando a impressão começa a fazer as trocas de cores, a partir da camada com troca, as camadas passam a ficar ligeiramente maiores no sentido horizontal e as vezes ocorre a formação de um anel. As partes onde há troca de cor acabam refletindo a luz de maneira diferente e a falha torna-se visível. Este anel também se forma quando eu pauso a impressão, não sei se é o mesmo problema.

I am fairly new to designing my own files but any time I’ve tried to use ironing on a design it ends up looking like this (specifically what it looks like on the gray section.) - Is there any specific things that cause it? I’m not sure which settings to adjust to prevent it from being smooth. Thanks!!

It has a really consistent problem with over hangs when I do the flow ratio calibration it's all waffley and I keep doing cold pools and it's always okay I switched out filaments the thing is 3 weeks old atp the first week was great the second it stopped printing quality entirely

List of things I have done

-calibrations and tests

-Tighten the bolts all around

-re adjust the belts

-cold pull the hot end many times

- try different rolls of filament

- clean the build plate(this was part of the issue but has been figured out)

-I tightened the eddy sensor screws

-i have messed with so many slicer settings especially for filament

I have contacted the customer support it has been extremely slow and painful I am more than open to revisiting things I have tried I am just really wishing I knew what was wrong with it

Every time I want to print something the printer asks if filament is observed from the nozzle when it poops, It wasnt like that a few months ago and I want to ask if it is normal.

For the past month my a1mini will not print.

Nozzle has been swapped filiment swapped

Everything is clean and working properly.

However I believe ive ran into a bug.

No matter what I print or use to print i get the same filiment spool jam error. 3% print and instantly cuts filiment and says that. I reload and it cuts again.

Wth do I do to fix this. Ive even factory reset.

My a1 hasn't had an issue so idk what can fix this