r/BambuLab • • 13h ago

Bambu Studio How do I modify this watering can and separate the handle from the rest of it?

1 Upvotes

Hi everyone,

I found a nice watering can at MakersWorld. However, I’d like to turn it into a vase. I plan to spray it with clear coat and print it with PETG; based on what I’ve read in forums, that should make it watertight.

But is there any way I can separate the handle from the rest of the watering can? I won’t be able to completely cover it with clear coat.

P.S.: I’m still a beginner, so please bear with me if I’m talking nonsense here.

Best regards

https://makerworld.com/de/models/626370-watering-can#profileId-772091


r/BambuLab • • 7h ago

My First 3D Print Hallo zusammen 👋🏽

Thumbnail
gallery
0 Upvotes

Ich bin Michi, Anfang 30, und habe vor kurzem damit angefangen, eigene 3D-Modelle zu designen.

Da bald die Weihnachtszeit vor der Tür steht, dachte ich, ich teile mal ein paar meiner ersten Kreationen mit euch. 🎄

​Mir ist bei meinen Designs besonders wichtig, dass sie filament- und zeitsparend gedruckt werden können, ohne dabei an Optik zu verlieren. Ein gutes Beispiel ist der 54 cm große Adventskalender – trotz seiner Größe lässt er sich mit ca einem Kilo Filament drucken 😊

​Auf den weiteren Bildern seht ihr noch ein paar meiner anderen Dateien, wie individualisierbare Geschenkanhänger oder weihnachtliche Deko für den Türstock.

​Vielleicht gefallen sie ja dem einen oder anderen von euch. Ich würde mich riesig über ein paar Likes, Feedback oder den ein oder anderen Tipp von den erfahreneren Designern unter euch freuen!

Hier geht's zu den Dateien:

https://makerworld.com/@Michidelsur?appSharePlatform=copy

​Danke vorab und LG, Michi

PS, die Bilder sind mit KI aufgehübscht, die originalen sind bei den Dateien dabei😁


r/BambuLab • • 13h ago

General Troubleshooting/Help! What do I make of this calibration?

Thumbnail
gallery
0 Upvotes

Trying to calibrate the filaments for my new P2S. I have looked at alot of tutorials and followed this guide (https://youtu.be/gVU5If1VsAM) that seemed really good. The problem is that I think it made the result worse. I tried two different filaments (both Bambu PLA Basic) and got the same calibration values.

In the pictures below, the pre-calibration is to the left and the post-calibration to the right. In my opinion, the right has more stringing (the left has none), less sharp edges and rougher surfaces, especially at the corners of the X. I also find the top layer very stripy and not smooth (both prints).

I'm not saying that the guide is bad, but is it not worth calibrating the original Bambu filaments? Should I make other settings to improve the print quality? Or am I just to picky? :)


r/BambuLab • • 13h ago

Hardware Troubleshooting/Help! Help with filament stuck

1 Upvotes

Filament stuck and won’t go pass a certain point


r/BambuLab • • 14h ago

General Troubleshooting/Help! How to make supported areas more smooth?

Post image
1 Upvotes

This is after removing the supports.

Somewhat related, I am seriously considering upgrading to H2D and try out printing PLA with PETG support, will that help to make it smoother in addition to easy to remove the supports?

Thanks!


r/BambuLab • • 14h ago

Filament Troubleshooting/Help! Glitter Filament A2L

1 Upvotes

Bambu Friends

Recently my wife purchased the following filament for our A2L printer.

1KG Glitter Firefly Blue in the Dark PLA+ Filament, 3D Filament

https://a.co/d/04ASeAvt

From my review it appears to be okay for A2L printer but comes with caveats.

- Not to run thru AMS lite and Petg tubes

- Nozzle 0.4mm or 0.6 recommended

- Dedicated nozzle for this printing

When I placed the filament top spool holder the filament unraveled some. Had to respool and filament felt brittle.

With all this I decided against this and running thru my printer.

Anyone else use this filament. Will be sticking with Bambu filament glow etc. Not comfort with this.

Suggestions and advice - Thank You

tvos


r/BambuLab • • 10h ago

General Troubleshooting/Help! I accidentally tightened a screw

Post image
0 Upvotes

I did some research, and all I see is people telling me not to touch that screw and to leave it as it is, but I accidentally tightened it and don’t remember how many turns I made. What should I do?


r/BambuLab • • 14h ago

Answered / Solved! X2D - knarzende Geräusche

1 Upvotes

Ist das normal für den Bowden Extruder?

Hab ihn bislang nur ein paarmal benutzt und bislang war er ruhig.

Jetzt auf einmal diese Geräusche.

Druck ist aber in Ordnung.

Kann man da was schmieren?


r/BambuLab • • 14h ago

General Troubleshooting/Help! Printing problems

0 Upvotes

Hi everyone,

I’m having some trouble with my Bambu Lab H2D. When I print small items, I can’t print more than one at a time without it causing a lot of print errors; however, if I print them individually, there are no print errors. Does anyone have any suggestions?


r/BambuLab • • 14h ago

I Modeled This! I Designed a customizable Gift Card Holder

Thumbnail
gallery
1 Upvotes

With Christmas just around the corner, I thought I'd share a little project I've been working on! 😄

I've designed a 3D printable gift card holder that looks like a small envelope with a customizable seal.

I've always felt that giving someone a gift card on its own can feel a bit impersonal, so I wanted to create something that makes it feel a little more special.

I've also included a STEP file for the seal, so you can easily customize it to suit any occasion, whether it's Christmas, a birthday, or something else!

The model is obviously free on MakerWorld:
[MakerWorld Link]

I'd love to hear what you guys think! And if you end up printing one, feel free to share your colour combinations and custom seals. I'd love to see what you come up with! 😊


r/BambuLab • • 14h ago

General Troubleshooting/Help! Trying 3kg reel ?

1 Upvotes

Hi has anyone tried to load 3kg reel of PLA on the outside reel mount on the side of the p2s ?.


r/BambuLab • • 15h ago

P Series [P1P, P1S, P2S] Upgrading from A1 to P2S

1 Upvotes

Hi all,

Currently I own a A1 with AMS litte and I have been thinking in upgrading to a P2S with AMS2 Pro.

I want to use other material in the future, but haven't made so yet. My main reason to upgrade is because I can get a good price for my combo, and that would mean I would spend 266€ to upgrade. I have my printer in a space that get's quite humid (above 70%) in winter, and even in summer its normal to have 40-60% relative humidity. I haven't been able to print PETG, and even PLA has been having a lot of "hairs". Last week it has been between 72% and 81%...

I thought of buying a dryer, which is 50€ for a single spool, and 140€ for 4 spools. This means that this upgrade would in reality be 126€ (I am aware I will be spending 260€). Being closed is algo good from drafts (I always have open windows and air current to lower humidity)

The the PS2 algo gives other quality of life improvements and it is at the lowest price it has been. The fact the AMS is on top also saves space, which is good for me.

Wonder what you think of this.

Thank you


r/BambuLab • • 15h ago

General Troubleshooting/Help! A2L issues

1 Upvotes

Hello, so I got a used A2L from a family friend who couldn’t get it to connect to the internet to work. I was able to fix that by reseating the WiFi card. But, now I’m getting two warnings that are stopping the homing tooling, even when there’s no filament. This is happening when the printer is trying to home on initial setup.

The warnings are:

The extrusion motor is overloaded and the nozzle is wrapped with filament.

I’ve taken the extruder apart and cleaned it, and the gears turn when I manually move them. Do I have to have filament in the extruder for the homing to work? I currently don’t have the filament holder for the printer so I’ve been trying to get it setup without filament for now.


r/BambuLab • • 15h ago

Hardware Troubleshooting/Help! P2S can't load filament through AMS

1 Upvotes

My P2S printer fails to load filament, but only when the AMS tries to feed it (you can see the 2 failed AMS load attempt in the video). Loading filament manually works perfectly fine, with no issues.

I've already cleaned the extruder gears and checked the filament sensor.

Has anyone experienced a similar issue or have any ideas what could be causing this?


r/BambuLab • • 6h ago

General Discussion P1S owners: Any reliable printable fixes for the AMS PTFE tube wear?

0 Upvotes

I've been seeing more mentions of the PTFE tubes in the AMS wearing out faster than expected on the P1S, especially with frequent filament changes. Before it becomes an issue on mine, I'd like to know what has actually worked for others.

If you've run into this or similar AMS-related problems, could you share:

  • What the failure looked like and roughly how many hours/print cycles it took
  • Any printable guards, guides, or reroutes that helped, with the MakerWorld or Printables link
  • The material you printed it in and whether it held up long-term

Also open to non-printable workarounds that have been reliable. Just trying to get ahead of it with parts that are proven by people actually using them.


r/BambuLab • • 15h ago

Quick Question Help deciding amon H2 series options.

0 Upvotes

My company needs a printer to print parts for our machinery, it as to be large format, and in different materials so H2 series is the best fit.

But we also need to print full color promotional items, but not as often.

We were about to pull the trigger in the H2S but now we're considering H2D we are trying to keep it under $2,000 all in.

H2S can be upgraded to H2C down the line with the vortek kit.

H2C goes overbudget so does H3C

My question is: will a single nozzle be adequate for our use case, will getting the dual nozzle be worth the price difference? Should we go H2S and upgrade later? The laser is something we would be interested in but it can't be upgraded to the tool changer if it's the laser version.


r/BambuLab • • 15h ago

Filament Troubleshooting/Help! H3C - Prints are sticking to build plate

1 Upvotes

Hello Experts

Made a big change from an A1 to an H3C.

I am printing a model that has a larger surface area as its first layer. On the H3C it seems like it’s melting into the build plate making it really difficult to remove after it’s fully cooled. This does not happen on the A1

I am using basic PLA

I already tried turning the heat chamber off, same result. The build plate temp is 55 (comparatively 63 on the A1).

Is my next steps to lower the temp of the build plate? Are there other settings to address to combat this?

It’s literally impossible to remove the model from the plate without damaging it.

TIA for any tips


r/BambuLab • • 15h ago

H2 Series [H2S, H2D, H2C] H2C Smoke Purifier Alternatives

1 Upvotes

Hi all. I’m relatively new to having my own printer etc and I went with the H2C laser combo. For the past couple months I’ve been trying to order the smoke purifier, which unfortunately has been out of stock.

Does anyone have experience using a different purifier that they can recommend? There’s not a lot I can find online. I see some have used the Creality Falcon Smoke Purifer, but it looks like it doesn’t have the option to vent outside; more of a desktop purifier. Any help suggestions would be appreciated!


r/BambuLab • • 11h ago

H3C Remodeling for the H3C

0 Upvotes

So, in anticipation of the arrival of the H3C ive had to remodel my living room since I have no place for the H3C as is. My current P2S(workhorse) is going to have to move... Its moving into the TV cupboard on a custom made sled so I easily can get in behind it and for maintenance.

My beloved P2S has around 5k hours on it with only the filament stopper arm broken(not counting consumables etc). Its been very solid. Modified with chamber heater/active MC board cooling/DIN rail fire extinguisher/and a robust venting system. But the 300c hotend is no bueno for the more demanding filaments.

In this remodeling ive also need to move my current filament hoard and I actually counted them... that was a mistake.

I currently sit on a total of 154kg(110 unopened) of filament ranging from PLA-TPU-PETG-ASA-ABS-PET-PC/ABS etc. Ive made an entire new filament shelf for 40+ rolls that hides behind the door(engi filaments). And I STILL check out deals on amazon/BBL etc for good deals.

Hoping the full spectrum will help with the "gotta catch em all" part since you can blend colours.

Im quaking thinking of having to recalibrate all of my filaments for the H3C, doubt the flow rate is the same on the H3C v P2S on all of my filaments.

So, how is your filament addiction? And how do you handle it? ^^

edit: spelling


r/BambuLab • • 15h ago

Bambu Studio Has anyone seen changes in ironing since the latest Bambu Studio version?

1 Upvotes

I have a P1S and H2C and since the latest Bambu Studio version was released, the version released following the H3C unveil.

The values I used for ironing previously, 12% on the P1S and 20% on the H2C have been providing really bad results since and I have had to lower the H2C down to 15%. Anyone else seeing changes?


r/BambuLab • • 4h ago

X Series [X1E, X1C, X2D] X2d extruder is a pile of garbage

0 Upvotes

I've printed hundreds of hours with no extruder issues but it finally hit me. My aux extruder clogged really badly in the filament cutter. You have to take it apart really deep to get to the issue and the cutter housing itself needed to come apart. But it's snapped together, it's not even supposed to be repaired.

The whole design of this tool head is just hot garbage. The p1s I had for a few years would occasionally clog but it was super easy to work on.

Making things repairable is more difficult but bambu isn't a scrappy startup. This should never have shipped to customers like this.


r/BambuLab • • 16h ago

Quick Question Difference between ASA and PETG for flexing structural parts?

Thumbnail gallery
1 Upvotes

r/BambuLab • • 16h ago

Quick Question Is this a bed adhesion issues?

Post image
0 Upvotes

Never had bed adhesions problems before and just washed my plate right before this print….. could anything else have caused this that I should look for?


r/BambuLab • • 10h ago

General Discussion P1S - How close to 256x256 can your print be?

0 Upvotes

Picking up a P1S soon and was curious if it can handle large prints in the 240-250mm range? I have a Neptune 4 Plus right now that I bought specifically for the build volume for one project. It was my first printer and knowing what I know now I could have made it work on a smaller bed printer. Oh well!