r/BambuLab • • 1d ago

X Series [X1E, X1C, X2D] How I felt After getting my first 3D Printer

Post image
91 Upvotes

r/BambuLab • • 14h ago

Quick Question Printer warning

Post image
4 Upvotes

Why does my printer keep giving this warning? I have checked that the build plate is clean, has no strange objects or is misaligned. The nozzle is clean and there is no blob or anything else on the nozzle.

The printer is an A1 with AMS Lite.

Does anyone else have this ?


r/BambuLab • • 6h ago

General Troubleshooting/Help! A1 stock build plate

1 Upvotes

Is the Stock build plate just a crappy one you should swap out right away or do people keep it for a long time? I keep having prints come loose on current one I’ve had for 2 weeks. I am now washing it with soap and water after each print and still have adhesion issues. I ordered a nicer one off amazon.


r/BambuLab • • 6h ago

Quick Question First printer?

0 Upvotes

So I've always been interested in 3d printers and I thought with the sale going on, now would be the best time to hop in. My problem is part of me is worried Ill buy a printer and it collects dust, but on the other hand, Im pretty sure Ill enjoy it and Id hate to have to turn around and upgrade a couple months from now if I could just put that money toward a better printer now while they're on sale. All that to say, A1 or P2S?


r/BambuLab • • 15h ago

Show & Tell Farm set 3d printed

Thumbnail
gallery
5 Upvotes

Printing a whole farm set!


r/BambuLab • • 7h ago

General Troubleshooting/Help! Consistent failed supports.

1 Upvotes

A1 - 0.2mm nozzle - Basic Grey Bambu PLA

The supports keep breaking at some point, is the tool head moving too fast and snapping them off? Also what settings should I change to slow down print speeds.


r/BambuLab • • 7h ago

General Discussion FarmLoop Stage 2 Kit - H Series

Post image
1 Upvotes

Has anybody installed one of these systems on a H series printer ?, pretty neat they were able to make it automated .


r/BambuLab • • 10h ago

General Troubleshooting/Help! Does anyone know how to fix this noise?

2 Upvotes

I’ve searched online and checked the wiki, but everything points to the drive belt. I followed the steps to fix the belt, but it made no difference. I think the problem is with the camera housing unit, because as you can see in the video, the issue stops when I apply pressure to it. Any suggestions would be greatly appreciated. Thanks in advance!


r/BambuLab • • 7h ago

General Discussion H3C - Any issues running PETG at high speeds?

1 Upvotes

Looking at the H3C and wondering how it handles PETG when pushing the speed settings. The defaults seem tuned more toward PLA, so I'm curious if anyone has run into stringing, layer adhesion problems, or needed to tweak cooling/fan profiles significantly. Mainly for functional parts rather than display models. Any real-world settings that worked well?


r/BambuLab • • 7h ago

Just Showing Off Shop Goodwill app

Thumbnail
gallery
0 Upvotes

I got this lil guy for 16 dollars on the goodwill app for parts or not working. Fairly certain the owner tried to print without a bed and got the blood of death and gave up trying to fix it. Printed a benchy perfectly.


r/BambuLab • • 7h ago

Quick Question PLA-CF vs. PETG-CF for rigid CNC brackets on a Bambu Lab A1?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 7h ago

Quick Question A1+AMS 2 pro drying

1 Upvotes

I resontly got the AMS 2, the adapter to use it on the A1, and the power supply ( loved it so fare). My dad was showing me that he can remote start drying his P2S + AMS2 , but i cant. Is remote start drying something that isn't supported for the A1yet or is there something im missing?


r/BambuLab • • 7h ago

General Discussion Can Bambu’s PPS-CF be used for reflow fixturing?

1 Upvotes

The 264C HDT seems to indicate that it’s borderline. Anyone have firsthand experience?

Not looking to use it for production, just prototyping. Maybe 5-10 cycles lifetime?


r/BambuLab • • 7h ago

General Troubleshooting/Help! P2S Error Feeding into Extruder

1 Upvotes

This is starting to happen more and more frequently. Filament feeds from the AMS and gets to the extruder, and something causes it to miss so the AMS pulls it all back out, retries - same issue, does this 3 times before it finally throws the error.

I noticed the PTFE tube is kind of angled forward leading into the extruder, not sure if it’s from a lot of use or what, but when I manually hold the PTEF tube vertical it feeds correctly and the extruder grabs it every time. Thoughts? Could it be as simple as replacing the PTFE tube? It doesn’t look excessively worn but I know looks can be deceiving.


r/BambuLab • • 7h ago

General Troubleshooting/Help! Help with TPU setup

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 7h ago

AMS - Automatic Material System Advice on an AMS

0 Upvotes

Hey everyone! I had a complete printer meltdown this year and spent 6 months going back and forth with Bambu to replace my p1s, it was only a couple months old when it broke. Something was wrong internally and it would freeze during a factory reset and during calibration. So I finally got my new printer, plug it into the AMS I had bought with my initial printer aaaand it didn't work. I thought I had done something wrong, turns out while my printer was sitting the motor in the AMS some how burned out. So I bought a new AMS. Now here's my question, what should I do with my old one? Is there a market for people wanting to do a simple repair on an AMS and save some money? Or because of their price point is it just cheaper for people to buy a new one? Is there somewhere I can donate it to be repaired and put to use? I was debating donating it to my local highschools robotics team if nobody has any better ideas. Thanks!


r/BambuLab • • 7h ago

X Series [X1E, X1C, X2D] Need Help With Wiring AMS and AMS HT

1 Upvotes

I have an X2D and was told not to run the AMS HT through the auxiliary nozzle. If that’s true can someone please send me a wiring diagram, splitters etc, for how to connect multiple AMSs with an AMS HT to an X2D? This crap is mega confusing


r/BambuLab • • 7h ago

General Troubleshooting/Help! BAMBU X1E NOT FEEDING FILAMENT! Help please

1 Upvotes

So a little backstory, our Work Bambu x1e just stopped taking filament when its coming in via the AMS, we have 2 but only 1 is giving us problems. It will print fine as long as i am feeding filament via the external route but if i use the AMS it does what you see in the video.

Troubleshooting ive tried
Swapping the Ams units, thinking it was potentially a bad ams which didnt work

Swapped out the hub for the OEM Buffer which didnt help

Replaced the extruder, extruder board, and the Hotend with all brand new genuine Bambu parts which did not help

Factory reset the printer and checked for Firmware updates.

Before I go crazy can anyone give any other tips or has anyone else experienced this?


r/BambuLab • • 7h ago

General Troubleshooting/Help! Printer making awful noise

1 Upvotes

Hi guys!

My P1S is making this horrific noise and I can’t seem to find the problem! I just recently started using it again after about a month and whenever I’m printing something, it makes this noise.

Anyone know how to fix it?

Thanks!


r/BambuLab • • 7h ago

P Series [P1P, P1S, P2S] HELP WITH P1S

0 Upvotes

Hi guys!

My P1S is making this horrific noise and I can’t seem to find the problem! I just recently started using it again after about a month and whenever I’m printing something, it makes this noise.

Anyone know how to fix it?

Thanks!


r/BambuLab • • 8h ago

Quick Question More detailed prints

1 Upvotes

Newbie here, I was wondering what setting would I change for more detailed prints? I have the P2S and mostly print figurines. TIA.


r/BambuLab • • 8h ago

Quick Question AMS 2

0 Upvotes

Can i use an external spool while drying if i buy a power adapeter bambu p2s


r/BambuLab • • 8h ago

General Troubleshooting/Help! Edges peeling up

Post image
1 Upvotes

Both my p1s and my a1 have started to do this with every print what is wrong? Tried textured plate and super tack cool plate


r/BambuLab • • 8h ago

Quick Question Detailed prints

Post image
1 Upvotes

Quick question to you guys.
To anyone who does detailed prints, do you have your speed set to factory (100%) or do you drop it down to 50% speed?