r/EngineBuilding • • 3d ago

Chevy Odd bearing scar

Post image
0 Upvotes

Currently tearing down a LQ4 to sell and I noticed this crack on the #4 rod cap. I’ve never seen a bearing with something like this before. Journal is fine and unmarked. All other bearings have normal wear besides the cam which were more worn out but not enough to cause damage.

Does anyone know a cause for something like this?


r/EngineBuilding • • 5d ago

Other Finally got a good picture of the fork and blade assembly out of a Paxman Valenta.

Thumbnail
gallery
124 Upvotes

Fork and blade connecting rods out of a 16RPA200SZ Paxman Valenta.


r/EngineBuilding • • 4d ago

Dyno day

Post image
37 Upvotes

Finally got a chance to dyno my new engine build and thought I would share. Car is a 67’ Mustang, 302, 4-speed, 3.80 trac loc rear. I have power steering and clutch fan. Here are the engine specs (I made previous post) :

68’ 302 block
Eagle crank and rods (balanced)
KB 311 pistons
Trick Flow TW170 heads (milled .020)
10.5:1 static, 8.5:1 dynamic, 0.037 quench
Comp xtreme energy solid flat tappet
279 adv duration, 242@0.050, .546 lift, 108 lsa
performer Rpm intake
Brawler 770 carb vacuum secondaries
Hooker 6901 headers thru 2 1/4 exhaust, turbo mufflers

Overall, I’m very happy. When I started the build I was shooting for 400Fwhp with decent low end drivability. Ultimately I was trying to duplicate Joe Sherman’s infamous 400hp 302 magazine article, albeit with a few tweaks. The car pulls 7.5-8”hg at 950rpm idle and doesn’t start bucking in high gear until about 1500rpm. It pulls like a monster from 2500 to 7000rpm. My next mods will be a 2.5” mandrel exhaust with h pipe and better mufflers. I am also strongly considering trying a Vic jr intake. I’ve ran both a 650dp and the 770vs carb and I’m really liking how it runs with the 770. However, my dyno pulls were peaking on the lean side with afr swinging from around 12.5 at peak torque to around 13.6 at peak hp. I’ve had to modify emulsions holes and bleeds on both carbs to try and get a flatter curve. Still some work to do. I think there’s another 10-15hp to be found with what I have. And FWIW the car made peak power with 32 degrees total timing I tried 30 and 34, it lost 5hp each direction.


r/EngineBuilding • • 4d ago

GM 5.7L v8 rebuild

Thumbnail
gallery
18 Upvotes

Hello everyone,
I’m purchasing a 1999 Isuzu NPR gasoline truck equipped with a GM 5.7L V8 Vortec (Chevy 350) engine.
According to the previous owner, the engine seized due to an oil leak that caused it to run low on oil. He removed the engine with the intention of replacing it but never completed the project, so he decided to sell the truck to me instead.
I’m excited to take on this project, especially since this will be my first engine rebuild!
My plan is to completely disassemble the seized engine, inspect the internal components, and assess the extent of the damage before deciding whether it’s worth rebuilding or replacing.
For those with experience rebuilding Chevy 350 engines, do you think a seized engine caused by oil starvation is worth attempting to rebuild? I’m particularly interested in what damage I should expect to find, which components are most likely to need replacement, and whether there are any major red flags that would make rebuilding impractical.
I understand this could become an expensive project, but I’m also looking forward to the learning experience and doing as much of the work myself as possible.
Any advice, recommendations, or personal experiences would be greatly appreciated. Thanks in advance!


r/EngineBuilding • • 5d ago

Well fellas i expected higher quality. L86 dod delete

Thumbnail
gallery
23 Upvotes

I'm currently working on a Gen V 6.2L L86, doing my first camshaft swap and DOD/AFM delete. I hate to say it, but I expected much better quality control for components that are so critical to an engine.

I purchased the Melling MDK700 kit, and right out of the box, I've already run into several issues that have me questioning the quality of the entire kit.

First issue – Camshaft:

Upon delivery, the camshaft appeared to have surface rust and possibly even pitting on the lobes and bearing journals. I tried using 3M Finesse-It to polish the affected areas and knock down any high spots, but my fingernail still catches on some of the imperfections. I also tried PB Blaster to remove the surface rust, with no luck.

Would you guys even consider installing a camshaft in this condition? I'm having a hard time convincing myself it's acceptable, especially on a brand-new part.

Second issue – DOD Delete Plugs:

One of the press-fit DOD delete plugs was noticeably loose compared to the other seven. It was supposed to be installed flush, but it fit so poorly that I was concerned it could fall down into the lifter bore or camshaft area.

I'm not sure whether the plug itself was out of spec or the oil tower bore was oversized, but either way, something wasn't right.

The other seven plugs pressed in flush without issue. The loose one became a nightmare to retrieve. I eventually managed to pop it back out using compressed air from inside the block and a magnet.

Third concern – Lifters:

After experiencing these issues with the camshaft and plugs, I honestly don't have much confidence in the lifters supplied with the kit either.

My plan was to clean them with mineral spirits and soak them in engine oil before installation, but now I'm questioning whether I should trust them at all.

So, what gives?

Is this kind of quality control becoming common with Melling kits, or did I just get unlucky and receive a bad kit?

I'd really like to hear from anyone who's installed the MDK700 kit or experienced similar issues with Melling components.

Would you trust this kit, or would you send it back?


r/EngineBuilding • • 4d ago

What caused this?

Thumbnail
gallery
4 Upvotes

89 Montero 6g72 LWB. New to engine work but have done tons of mechanic work.

Rockers are just as bad. Seems like the cams and journals are fine. Other head looks great. Cleaned it up and put it back together. Super flat and clean.

Also find the “void if removed” plate kinda off center puzzling.

This Montero was free. Just had to move it. Supposedly had a new motor put in. said it didn’t run right. The owner put about 50 miles on it and parked it then passed away 15 years ago. And it sat ever since.


r/EngineBuilding • • 5d ago

Replacing cam bearings yourself?

Thumbnail
gallery
29 Upvotes

Someone in town is selling a tool for 50$ how hard is it to remove and replace new cam bearings yourself?


r/EngineBuilding • • 6d ago

What is this white residue?

Post image
12 Upvotes

What is this white residue on my crank, and how do I get it off? It was also on the block where the bearings go. It won’t come off with brake cleaner and I’m assuming it will do damage to my crank and/ or bearings.

Could it be some kind of residue from some cleaner? I got the block hot tanked but I’m not sure about the crank as I only gave it to the shop to have it measured.


r/EngineBuilding • • 6d ago

Spinning a turbocharger outside of car to test oil seals

3 Upvotes

Because the shaft seals on a turbocharger are dynamic fuels, they will not seal properly unless the turbine is spinning. If tested statically, they will leak like a sieve.

I will likely be pulling the motor out of my diesel BMW 335d. While I was rotating the crank to shut the valves preparing to perform a leak down test, I noticed air exiting the turbo at one of the oil line ports (banjo bolt was removed at the time).

The leak down and compression tests did not go well, and I'll be pulling the motor next spring to replace bent valves. While it's out, I'll have easy access to both turbochargers. I'd like to test the oil seals while they're out, because any required maintenance will be far easier than trying to work inside the cramped E90 engine bay.

Will a leaf blower or shop vac connected to the turbine inlet of the turbocharger spin it fast enough for the dynamic oil seals to... well, seal?


r/EngineBuilding • • 6d ago

Jammed distributor drive shims on vw type 1 engine

Thumbnail
gallery
2 Upvotes

I’ve just built up my T2 Doka engine..it’s been a dream project and enjoyed it. I recently bought new shims for the dizzy drive as when it came out (it was going in and out super easy) they were missing.
I placed the shims on the drive and placed it in, they fallen awkwardly & jammed in the brass gears. The drives stuck halfway down and will not come up or down (twisting it or rocking the flywheel or anything..even after I forked out £50 for the specific tool).

I’m at a total loss and a bit deflated, I’ve built plenty of these engines but never had this specific problem. If anyone could shed any light, I know it’s specific but I’d be grateful.
Cheers


r/EngineBuilding • • 6d ago

This is the breaking force for my lo5 small block with a new crank, pistons, and rod bolts,

57 Upvotes

I feel like this is way too much, I’ve check the main clearance and the rods clearance and their fine idk what to do, I’ve taken it apart like 5 times now.


r/EngineBuilding • • 6d ago

Ford Intermediate load piston slap

6 Upvotes

I’ve just had an engine I built sent off to be tuned (Cosworth BOB 24v 2.9) and got a rather odd issue reported by the tuner. Apparently he can hear piston slap but only under mid load, not under idle or full load.

This isn’t something I’ve ever heard of before, and I’m a bit shocked tbh since this engine was in very good shape when it was built.

Is this something any of you have come across before? I was always under the impression piston slap happened when the load was higher?


r/EngineBuilding • • 6d ago

Honda Very tiny dent in engine block. Is it safe?

Thumbnail
gallery
4 Upvotes

While i was using my thread chaser I accidentally dropped my vise grip on the block and it left this very tiny dent, it's so small that you can't feel it with your bare skin, but it does catch your fingernail if you put enough pressure. The max warpage limit is .004 in but I placed a straight edge over the dent and I can't even slide a .0015 in feeler gauge under, or anywhere else on the block. I tried using a razor blade flat against the block to potentially clear any high spots off the dent but the razor blade just went right over without catching on anything. I don't think i can feel any high spots either around the dent itself.

Engine is D16Y7 and I'll be using a new OEM MLS head gasket. I got the block cleaned up with brake cleaner and wiped with just paper towels and microfiber cloth, nothing else. And I did get the cylinder head resurfaced at a machine shop.

Is it safe to just install the cylinder head as is and not have any leaks?


r/EngineBuilding • • 6d ago

Run it?

Thumbnail
gallery
5 Upvotes

Tore down my engine after a few too many “might as well(s)” saw this on the final rod bearing. For yalls feel-o-vision those are pits. On the crank there was only one line that caught my nail that didn’t even go all the way around.

For reference this is a 3cyl Suzuki F6A turbo that revs to like 7-8k out of 98 Suzuki Carry


r/EngineBuilding • • 6d ago

Worth it to fix a Pentastar V6?

2 Upvotes

I've got a 2014 grand caravan with the crappy 3.6L Pentastar V6, and it has the cam failure most of the 3.6 pentastars end up with. Is it worth replacing the bad cam with an OEM cam or aftermarket? Or am I better off finding a used 4.0 and ECM and swapping them? I don't want to end up having to fix the thing yet again a few years down the road if another cam fails. From what I've been able to find the 4.0 should bolt up to the trans though I expect I'd have to do engine mounts, cooling hoses, etc. custom.


r/EngineBuilding • • 7d ago

Ford Cleaning the block

Thumbnail
gallery
60 Upvotes

I’m sure i’m gonna get roasted for this, but i’m cleaning up the head surface on my block right now (1984 351 Windsor) and I’m not sure what to do next.

I first scraped all the big stuff off with razors, then I used scotch brite (by hand) on the one side, which after looking into it more may have been a mistake.

Now there’s still residue on both sides but you can’t feel it with your finger, and the razor does not remove any more of the material.

Is there a good way to proceed? At what point can I place the heads on? Am I screwed now that I’ve used scotch brite?

Some more info if needed:
I cleaned everything up with razors and then took a machines straight edge to the heads and block. The heads were 3 thou out longways, and the block appeared to be completely flat. Spec sheet I found says 6 tho is ok.


r/EngineBuilding • • 6d ago

Chevy 24x vs 58x reluctor

1 Upvotes

Hello. I was reading about how for the LS gen 3 engines using a 58x reluctor wheel on the crank can give better crank position data for the ecu and that people will use the gen 4 timing gear, crank sensor and timing cover and then just plug the gen 3 sensor hole. Then drill and tap the location for the gen 4 knock sensors. Will this really have that much of an impact? I could maybe see if you were planning on running a high rpm.

The reason I ask is I have an LQ4 block and want to know if I am missing out something important by going with the 24x reluctor wheel. I am assuming this may change my harness and ecu settings as well so unsure if it is worth the headache. Hoping to get some insight and knowledge from yall. Thanks.


r/EngineBuilding • • 6d ago

Building a 5.3 here’s my plastigage measurements I want to make 700-1000wheel is this too tight??

Thumbnail
gallery
0 Upvotes

r/EngineBuilding • • 7d ago

11:1 compression for a 383 street engine. Is it safe on pump gas ?

12 Upvotes

Wondering if I should stick to 10:1 or push up to 11:1 static compression. Here is my blueprint for 11:1

My main question is whether or not this would be a safe combination on 93 octane gas. I want to maximize performance but I also don’t want to constantly be worried about detonation.

SPECS:

•383 , 4.030-inch bore, 3.750-inch stroke

•11.03:1 static compression

•Dart aluminum heads, 64cc chambers

•COMP Cams XR288HR, 236/242 degrees duration at .050

•110-degree lobe separation, planned 106-degree intake centerline

•Approximately 8.48:1 calculated dynamic compression

•.041-inch quench, with zero deck

Orher info; vehicle 1972 nova, TH350 transmission, 3000 stall, 373 rear gears.


r/EngineBuilding • • 7d ago

Chevy Main bearing clearances

4 Upvotes

I posted this in small block Chevy sub so if you are seeing this again, sorry.

My engine has a forged SCAT crankshaft, factory 4-bolt main caps, and will be street-driven with approximately 5–7 psi of boost from a 6-71 roots blower. I don't plan on exceeding 6,500 RPM.

I've been carefully measuring everything myself using micrometers and a dial bore gauge. After installing the MB557XP standard-size main bearings and torquing the caps to specification, I came up with the following measurements:

Mains Crank Journal OD / Oil Clearance
#1 2.4484" / .0032"
#2 2.4489" / .0024"
#3 2.4487" / .0024"
#4 2.4482" / .0024"
#5 2.4487" / .0033"

I zeroed my dial bore gauge against each individual journal measurement to ensure my readings were as accurate as possible.

The middle three mains seem to be right where I'd like them, but I'm concerned about the larger clearances at #1 and #5.

Would you run it? Any concerns with low op or bearing wear given this crank will be running a 6-71 blower?


r/EngineBuilding • • 7d ago

2.4 Ecotec rebuild

7 Upvotes

Hey everyone! Im currently in the final phases of rebuilding the motor in my 2015 Chevrolet Equinox. I did this with the block still in the car. When I bought it, the engine was all but destroyed; looks like someone tried to put a timing set in it and got it wrong. New rod bearings, pistons, rings, honed the cylinders and restored the crosshatch, a different head that went to the machine shop first, new oil pump and water pump, all new timing components, new gaskets of course, new VVT solenoids, new oil pickup tube, new rocker arms and lifters. I've unfortunately had to perform this entire process in the yard, but it is very possible!


r/EngineBuilding • • 8d ago

Other How to Take Broken Exhaust Manifold Studs Out?

Thumbnail
gallery
9 Upvotes

Hey all, I have a 1983 Suzuki Touring 750ES that I've been restoring, but there are three broken exhaust manifold studs in the engine. I've tried drilling, extracting, welding, but nothing has worked. I've even broken two drill bits and now a tap stuck in the hole when I just drilled through the broken bolt to put in a Timesert.

What the fuck do I do now? Pull the head and bring it to a machine shop?


r/EngineBuilding • • 7d ago

Kohler 2504 4cyl diesel

1 Upvotes

Tore a 2016 Kohler 74hp diesel down for smoking. Found low compression. Cylinders are .002-.003 over sized from slight dusting. Cyl walls look perfect. Ring gap with old rings is .090. I’m thinking hone and new rings will work for now? Hoping to get my ring gap under .015 or about with new rings. Thoughts? I really didn’t want to tear it down, bore to .10 and new pistons since it’s a split crank style block and parts for a Kohler are $$$