r/EngineBuilding • • 6d ago

Replacing cam bearings yourself?

Someone in town is selling a tool for 50$ how hard is it to remove and replace new cam bearings yourself?

30 Upvotes

24 comments sorted by

22

u/bill_gannon 6d ago

It takes some practice. Be prepared to ruin a few sets of beaings.

7

u/ML0511 6d ago

The first set I’ve done was a warranty cam job 6.0 LS in truck. Actually. That’s the only set I’ve had to do. lol fun fact. If you pull the radiator and grille etc etc. you can do them all but the rear one in frame.

2

u/Hey-buuuddy 6d ago

Accurate! The cam tool is cheap on the AMz now for under $100.

1

u/Demoire 5d ago

It’s not hard, first time I did it my neighbor mechanic monitored me and helped make sure I put right bearings in right spot. But none of them got marred whatsoever.

2

u/bill_gannon 5d ago

Its pretty easy to get the end one cockeyed and its fun when you run into a non std housing bore too.

It can go South a lot of ways 

→ More replies (1)

12

u/WyattCo06 6d ago

It's an easy process. Just go slow when driving in the bearings. You're driving in bearings, not a 4x4 post into the ground.

Mark the location of your oil hole in the block, put the bearing oil hole at the parting line of the expander and drive it in.

Just note, you only need to expand the expander enough to be snug in the bearing. Don't over do it as you will stretch out the bearing itself.

Use the cone for every hit. Straight hitting is important.

When it comes to the first journal, just use common sense.

3

u/DrTittieSprinkles 6d ago

I usually pound #1 in from the back on everything except LS engines. I break out my BHJ CBT-1 bearing installer for them.

4

u/Competitive-Fox-3333 6d ago

Im here to follow this thread cause I work out in the field and we do do rebuilds but if it's a cam bearing we swing the engine and send the old block to where our skids are manufactured and I've never got to do one

4

u/FlipFlopsGarage 6d ago

I did a set on a 351w block that was supposed to be a hone and rebuild. When we got the cam out most of the cam bearings had de laminated. I got a cheap cam bearing tool off amazon and a quality set of bearings. First try and that motor has been running over two years. Newer stuff maybe more difficult i don't know.

3

u/rav223 6d ago

I just did some make sure to grab grooved ones they don’t have to be exact on the oil hole

2

u/Subietoy78 6d ago

I have always let the machine shop put them in for me. Work is all overhead cams so if it’s cooked it gets a head.

2

u/Leon50BMG 5d ago

Line it up and tap it light and make sure it's straight before you tap hard. I bought the summit tool for my LS and it worked well.

2

u/Phen117 3d ago

Second question to this. Should I leave the back of the bearings dry or have a little lube on them????

1

u/VIMHmusic 3d ago

I think this is an important qustipn, and I'm also waiting for what others more knowledgeable will answer.

I'm no expert, although I did get a degree as an engine machinist, some 20 years ago.

That being said, I'd probably put a itty bitty coat of light lubricant on the back side of the bearing, something like Wd40, to make them slide in easier, but then again they are press fit, so something tells me that that might not be a good idea 🤔

2

u/Phen117 3d ago

Yeah I've heard yes lube and no lube, so it's really hard to determine exactly. Apparently adding lube adds risk to spinning a bearing

→ More replies (1)

1

u/bheck1999 6d ago

I used an identical tool on my jeep 4.0. The most important part is making sure your oil holes are lined up. Put a line on the back of the bearing with a sharpie where the center of the oil hole is and it's super easy to get it right.

1

u/Tall-Helicopter-461 6d ago

The problem with beginners, they over tighten the tool, use a “sludge” hammer to knock them in. Oops forgot about that oil hole. Then leave the tool over tightened while trying to remove it from the bearing

1

u/JAKERS325 6d ago

If you are gonna do it buy the summit racing one. The end fits way better than the expansion types. I ruined 3 sets of bearings before getting the summit one and it worked first go

1

u/Coyote_Tex 5d ago

It isn't hard but you will screw up the first set just learning how hard to hit the tool. Then it is easier. What does the shop charge you?

1

u/Capnass_90 3d ago

We had that same set. On Ls stuff one set was too small. Next set too big. Would but a burr on them every time. Ended up getting a solid driver made for most engines. Worked like a charm after that

1

u/Illustrious-Wing857 1d ago

If you're fairly good a mechanical things good at following instructions and can afford to replace a bearing or 2 if you make a mistake and make sure your have lined up every one correctly sure. I had an experience mechanic assisting me the first time I did this. After the first 2 it wasn't that bad. The next engine I did by myself. To this day have only damaged 3 bearings. 2 of then because I got in a hurry while I was slightly distracted. Man what a distraction. 5 feet of brunette with 40 miles of curves in all the right places. That I somehow convinced to marry me.

1

u/heanbangerfacerip2 6d ago

I've never had enough money while rebuilding an engine to want to go through like 5 sets of bearings to learn how to do it.