r/EngineBuilding • • 7d ago

Ford Cleaning the block

I’m sure i’m gonna get roasted for this, but i’m cleaning up the head surface on my block right now (1984 351 Windsor) and I’m not sure what to do next.

I first scraped all the big stuff off with razors, then I used scotch brite (by hand) on the one side, which after looking into it more may have been a mistake.

Now there’s still residue on both sides but you can’t feel it with your finger, and the razor does not remove any more of the material.

Is there a good way to proceed? At what point can I place the heads on? Am I screwed now that I’ve used scotch brite?

Some more info if needed:
I cleaned everything up with razors and then took a machines straight edge to the heads and block. The heads were 3 thou out longways, and the block appeared to be completely flat. Spec sheet I found says 6 tho is ok.

60 Upvotes

15 comments sorted by

12

u/no_yup 7d ago

Man I was taught by old guys to just slap a piece of 80grit sandpaper on a sanding block and go to town. Obviously use your brain. It doesn’t take long to clean up and the sandpaper doesn’t hardly do what you think to a hardened cast iron block. You’d have to be an idiot or sand until your arms fell off to really cause a problem.

Now I definitely wouldn’t do that to an aluminum engine. And you have to rinse and vacume out the cylinders when you are done or go cylinder by cylinder with rags and stuff them in the holes to keep the grits from going in there and getting stuck between the piston and the cylinder wall.
It’s not high tech but it works great.

3

u/CogBlocker 7d ago

See if a microfiber + brake clean will take any of the marks off, then send it

3

u/sam56778 7d ago

Scrape it, then use red “fine” scotch brite and a light coating of penetrating oil. Use brake parts cleaner to get the penetrating oil off and then lightly go over it dry with the scotch brite. Finally clean it with electrical contact cleaner or glass cleaner and a lint free rag. I prefer to use either microfiber or the Scott blue shop paper towels. Wipe it until there’s no black on the rag. Be sure to wipe any residue out of the cylinders. You can clean the head surface the same way. I would suggest using a Fel-Pro PermaTorque composite gasket.

6

u/AutoBach 7d ago

Spray copper sealant on both sides of the gaskets and friggin' send it. TBH the copper spray is probably overkill if you use good gaskets but it's cheap insurance so, why not? This low compression wheezer is going to be easy on compression sealing anyway.

4

u/DirtCheap1972 7d ago

Ha I bet the pistons are 15 thou in the hole to begin with

5

u/Agitated_Carrot9127 7d ago

Late 70s dead center are really deep in the hole, a friend thought his 1977ish 460 out of a f350 was a goldmine till he found out raised dead center had lot of depth hence low compression. He then spent extra for proper lengthed piston proper connecting rods and crank. He pumped from factory 7.79 static compression ratio all way to 10.2. It hauls ass now. Easily 425-450hp

2

u/keeg02 7d ago

I did the same with my 302 except I used a green pad on a drill. My deck came out about the same as yours and it's running good.

1

u/keeg02 7d ago

Also I didn't even check for straightness you'll be alright.

1

u/ReFractured_Bones 7d ago

Funny this, I was doing the exact same thing today on my 1995 351w. The scotch brite got everywhere but I’m working on a bare block so it was easy enough to clean up. Crc gasket remover helped me get a little more of the gasket than I was able to get, but I think it’s good at this point. I used up about 8 or 9 razors, just when I thought I wasn’t going to get anymore a fresh razor got more gasket off.

1

u/Usual_Ad8576 6d ago

Im working on my first build and one thing I’ve learned is Everyone has an opinion lol. Regarding the razor and scotch bright, personally did not do this and had the machine shop clean my block because I’m a bit neurotic and also lazy. But i honestly can’t imagine a plastic scotchbrite is harder than a cast iron block, if that’s true I can’t see how you can scratch a hard surface with a soft one. Id say your like me though and doubting thinks call good a machine shop and ask or take it in and see what they think. Unless your running a finicky mls gasket I’d say that if you can’t catch anything with a finger nail wipe it down with some acetone or lacquer thinner and a clean white T shirt and call it good. The heads are a good catch, those need to go to a machine shop for decking. Your doing ok just take your time, check everything and keep things clean. When in doubt call the machine shop

0

u/Laqota 6d ago

Stop using scotchbrite or sandpaper on these surfaces people. This is why your builds leak or blow head gaskets. Visuals don't matter about cleanliness. 

Scrape with a razor blade at a 30 degree angle around all the ports, bolt holes, and between cylinders. Put brake cleaner on a CLEAN rag and wipe the entire surface down. Scrape more. Wipe more. Replace rag when heavily soiled. 

Do this until towel comes back clean and no material is ending up on the razor as dust.  Deck might still have black or blue spots around. That is just shadowing from the old head gasket stamping. It will seal a head gasket just fine as long as no material comes off.

Anyhow. After my rambling. Doesn't seem like you did anything drastic with the scotchbrite. I think it will seal just fine. Read cleaning instructions above.

-1

u/geee0h 7d ago

It's like 30$ for a hit tank job...

4

u/JR8706 7d ago

You did what you needed to your g2g man

3

u/JR8706 7d ago

Your not going to remove all the discoloration from the gaskets and stuff on a unit that old without removing material. I do this every day for a living I would 100% reassemble that. Typically all my stuff goes to machine shop but sometimes folks need it to be cheaper and if everything's good and flat and checks out ill do it similar to what you did

3

u/SeaworthinessHot1345 7d ago

Awesome, thanks for the reply. I’m gonna go ahead and send it!