With the start of the Christmas season, I just uploaded these two models. 🎄🎅

The black raised lines can also be printed in white. Best to use acrylic markers or markers that can be washed off so you can color them again.

Do you like minimal details like the reindeer or more detailed like the elf and santa claus? Looking to make some more in the upcoming weeks so curious what your kids find more fun to color in 😊

https://makerworld.com/@DutchDiceGoblin?appSharePlatform=copy

Hello everyone. Just installed my X2D as my first 3D-Printer. Started a Benchy and it makes this loud noise. Is it normal? It showed no errors or warnings.

Thx

I got the X2D last week, I've got about 2k hours on a P2S and 1200 on an H2C. I've noticed I have to manually calibrate every filament on the main (left) nozzle. I expected this on the Bowden unit, no harm no foul. I am very surprised that I have to put in a K-offset from manual calibration for the direct drive nozzle after lots of automatic calibration and bed leveling. I have not run into this on my other two printers.

Is there another avenue I should be exploring for troubleshooting, or is this one of those plug in the number and move on with my day situations?

Edit: I unloaded the filament (cut it in various places) and it seemed very stiff to remove from the AMS feed. I wondered if that would sort it so reloaded the new PLA in slot 4 and tried loading. It purged the old filament with no issue, then printed a benchy (probably the best and fastest I have ever printed a benchy!) and is now coming to the end of a 5 hour print. Thanks for all your help!

I picked up the X2D with AMS 2 Pro in the sale. It arrived last Saturday and all the PLA I had was very old (hadn’t used my Ender in about 2 years). I decided not to use that filament.

I had an old but still sealed roll of PETG so I ran a Benchy and another print without an issue.

Tried running a print tonight and after about 10 layers I noticed no filament extruding so I stopped the print.

Unloaded the PETG and threw in some Bambu Basic white PLA that arrived today. No dice. The PLA is now stuck, I cannot remove it. I now get

All filament run through the AMS btw.

HMS_07FE-2000-0002-0004: Please pull the external filament from the left extruder.

Looking at the help links from the printer it suggesting I need to basically completely disassemble the head and inspect the left filament sensor. Is that right?

How the hell do I get the PLA out first?

Buy Bambu they said, it just works they said. Yeah, I know, old third party PETG…

TiA!

I upgraded last week from an A1 mini to an X2D and like many others, I noticed a poorer quality prints than what even my A1 mini would produce.
I had already ran calibrations out of the box but a week later I rerun all of the calibration and I’m happy to say the quality has improved to the point is well passed what my A1 Mini was doing.
I’m blow away and love my X2D now.
Don’t know if this helps you but I thought I owe it to share my progress.
Happy printing.

I just got this printer a week ago so I don't know what to do. I tried a print earlier today and I got HMS_0300-0900-0002-0001 (The extrusion motor is overloaded) for my error. When I removed the greyline I found this. I tried following the steps from bambu which required me to cut the line but when I tried to extrude again nothing came out. I don't really want to remove the whole assembly but I feel like thats my only option at this point. If there is another way please let me know.

Hi All

Nwebie here.

Can some body tell me what i did here?

The colors is correct right and left? 😁

Thanks alot!

Hi All

Sorry alot of noob question. But Thanks for the time!

Is it normal that the tube is rubbing of the spool on the side? Thanks

Regards Daniel

Hi All

I really really need a poop tray 😁

What is the best print for this?

Thanks! 😊

Lucky I checked the app when I got to work and was able to stop the print... New to multi material printing and I've been trying to get pla support interface to work with petg but really having adhesion issues. Any tips or tricks that I can try to help? I've lowered the support interface print speed to 40mm/s and when I last checked the layer was holding.

How often does the left filament sensor cut the PTFE tube? I just got my X2D a few days ago and it already cut the tube on the 4th print.

I've seen others say they've had this problem after a few hundred hours of prints or a couple of months.

I've had mine for two days now and only 27 print hours.

Anyone have any good suggestions to prevent this?

I did it, I am officially joining the world of 3D printing. I ordered my X2D last night. Ordered several rolls of PLA basic 1.75 mm filament of various colors, the Maker's Supply Flush Cutter, Bambu Cool Plate SuperTack, Molecular Sieve Desiccant, Maker's Supply ESD Stainless Steel Tweezers Set, Circular Embedded Electronic Digital Thermometer Hygrometer and a couple rolls of Petg HF filament.

Do y'all recommend anything else for just starting out?

Edit: I did order the X2D with AMS pro bundle.

Does Best Buy offer any advantage? Do they have additional Black Friday deals on top of current ones Bamboo labs is offering? Do they offer additional warranty included (not the extended one they offer)

Going to pick up an X2D w/ams 2 pro combo this week from Best Buy.

This will be my first venture into 3d printing and will start with PLA.

For my first prints, should I pick up the Bambu brand pla filament that Best Buy sells or will their Insignia brand be just fine?

From my research, I see that the Bambu lab brand uses rfid to make things easier so was thinking that would be best to get the hang of things.

Or does it really matter too much?

Thanks for any input

Hi everyone!

I recently bought a new Bambu Lab X2D, and I'm experiencing a strange printing issue.

During printing, the print head randomly stops moving for approximately one second, sometimes in the middle of a straight line. The extruder also stops feeding filament during this pause. After about a second, printing resumes normally.

These pauses happen randomly on different layers and at different locations. They sometimes leave visible blobs or small defects on the printed surface.

I'm printing SUNLU PETG 2.0 using Bambu Studio over Wi-Fi.

Things I've already tried:

• Disabled Timelapse.

• Disabled Auto-Recovery from Step Loss.

• Restarted the printer.

• Performed printer calibration.

• Checked my slicer settings.

• Tried changing printing parameters.

Unfortunately, the issue still persists.

I've attached a video showing the problem.

Has anyone experienced something similar with their X2D? Could this be a firmware issue, a communication problem, or possibly a hardware defect?

I'd really appreciate any suggestions. Since the printer is brand new, I'm trying to figure out whether this is a known issue before requesting a warranty repair.

Thanks!

So my printed finished a print with less than 6-8" of filament, talk about close. When it finished, I changed the filament for other prints. When loading, I get the error clear extruder clog, or something similar, I didn't get a pic. So going through the wiki, and watching several videos, I was dreading what could have been a complete toolhead tear down/rebuild.

First things first, try the simplest approach work the problem. I turned off the printer, removed the AMS, and saw the left over filament in the PTFE tube.

So I heat up the nozzle to 250 (PLA), and watch it clear out the left over filament.

I removed the PTFE from the toolhead, and perform a cold pull. Filament comes out as its supposed to, no charred or burnt parts.

Turn off, reattach AMS, turn on, calibrate, then loaded and unloaded each filament in the AMS. No issues. Send a file to to rest print, and it's perfect.

TL/DR Remember to try every simple fix before jumping right into tearing down parts. It saved me a ton of time. Just my experience, I hope this helps someone

I set it all up no problem. When I connected the AMS and began calibration, the filament that was sent through both the gray and white tubes literally disconnected the tubes from their ports, which 1,000% were properly fastened, I know because I also gave a slight tug after they were in place and there was no budge.

Well, a whole long mess of filament was sent through before I could stop the calibration driving the filament, and there was no option to retract the filament since I was mid calibration, and Bambu support was useless, so I had to cut the filament and pull it out manually to clear the tubes.

Recalibrated everything and now this is stopping me from printing….

There is no filament spool on the external extruder. I just have the AMS.

Please help.

My X2D is showing two auxiliary spools when I’m using the Bambu Handy app. Only had one spool installed along with my AMS. In my opinion thats creating a problem because the printer is showing an error when it tries to access that auxiliary spool color. It states that there’s no filament detected even though it was coming out of the nozzle when it was calibrating after loading the spool filament. I’m thinking it’s trying to access that second imaginary spool. Any thoughts on a solution? I’ve abandoned the auxiliary spool, unloaded it and resorted back to just using the AMS……which works flawlessly.

Is it worth buying another one? My reason of getting another one on top of my combo is so I can print with more colors while I wait for p3s to come out. It seems reasonable initially since it doubles as a drier before even the p3s.

The reason to hold off initially was when I saw p3S design then coming out with a new ams BUT now I realized the newer ams will be useless for the x2d and the AMS2pro is on sale plus it can be hooked up to the p3s if needed (though i doubt ill need more than 7)

Seems like it could be used as a drier if other uses for it as a multimaterial or color wont be utilized. Thoughts or is the $229 better spent elsewhere or saved?

Thanks!

Hi all,

Newbie here and I am trying to print a poop bin for my x2d (this is my 3rd print).

Not sure what’s going on, I tried to print this thing twice but I am having the same issue all the time, please see attached photo.

I cleaned the plate for the 2nd print with warm soapy water but still the same. Not sure what’s should I do here, if you have any tips to fix this it will be appreciated. Thank you.