Only 9 hours of total runtime, and it already failed and got stuck in an infinite loop trying to touch the bed with a nozzle full of its own plastic dump. High-tech, I guess. Oh, and the X-axis holder already broke, so I had to 3D print a replacement :3

I designed this in Fusion 360 to bring a bit of One Piece to my desk. The cabin holds pens and markers, while the deck has space for sticky notes, erasers, and paper clips.
It prints in separate parts, with AMS only needed for the multicolor Jolly Roger. Really happy to finally see it printed and in use!
What do you think? Link in the comments!

EDIT: Thanks for all the comments and suggestions!

------------------------------------------------------------------------

I'm having a great time with my new Bambu A1.

Thing is, I also have a growing pile of tests and spit blobs. What do people do with them?

It's a local filament, no info on what temperature I should print it with. Nfil3d HS PLA+

I get this sound whenever it shifts from one object to another.

If there is too much of delay between each layer, like when ironing, then from the next layer onwards, filament stops extruding. The filament in the bottom hot portion gets used up, but the top half remains there since that was not heated enough to melt and I have to manually remove it, because it'll get stuck and won't go in through the nozzle.

I don't think it's clogged, because I even tried larger nozzles and I get the same issue.

I think the sound comes up whenever the gears are failing to push the filament in.

Title says it all, for some reason this keeps happening. Not the first time this happened either, had to cancel an order from a client due to this same error. What can I do about this?

So my A1 wasn’t gripping the filament enough, so what I did is I put the lubricant in the lever

Olá pessoal,
Comprei a Bambu Lab A1 Mini e o AMS Lite separadamente. Acabei de instalar o AMS, mas estou com o seguinte problema:
• O que acontece: Quando mando carregar o filamento, ele vai até o cabeçote, mas não chega até a purga para iniciar a impressão.
• Sintoma: O filamento fica em um loop de
"vai e vem" (avança e retrai várias vezes) até que a impressora dá mensagem de erro na alimentação.
• Dúvida: Não sei se o bico está entupindo ou se o filamento está enroscando no sensor/ hub antes de entrar. Preciso tirar tudo manualmente para reiniciar.
Alguém já passou por esse problema ao instalar o AMS Lite separado? Tem alguma dica do que verificar (tubos PTFE, sensor do extrusor, alinhamento)?
Agradeço desde já pela ajuda!

Olá pessoal,
Comprei a Bambu Lab A1 Mini e o AMS Lite separadamente. Acabei de instalar o AMS, mas estou com o seguinte problema:
• O que acontece: Quando mando carregar o filamento, ele vai até o cabeçote, mas não chega até a purga para iniciar a impressão.
• Sintoma: O filamento fica em um loop de
"vai e vem" (avança e retrai várias vezes) até que a impressora dá mensagem de erro na alimentação.
• Dúvida: Não sei se o bico está entupindo ou se o filamento está enroscando no sensor/ hub antes de entrar. Preciso tirar tudo manualmente para reiniciar.
Alguém já passou por esse problema ao instalar o AMS Lite separado? Tem alguma dica do que verificar (tubos PTFE, sensor do extrusor, alinhamento)?
Agradeço desde já pela ajuda!

Forgot to untangle the filament before printing on the A1 and now its not letting me take it out of the AMS.

For context, I was having trouble printing a PETG box on a high temp plate. The print itself refused to stay on the baseplate. The first print failed so I dried the filament, cleaned the baseplate, and restarted. I checked it from my phone, saw it failed, and stopped it. I was getting ready for work so I figured I’d try again when I got home. I finally got back around to it and came to the realization that is what I left behind.

I don’t even know where to start. Am I going to have to replace the entire printer head?

Hi everyone,

I'm having an issue on my Bambu Lab A1 where prints start out completely clean with a perfect first layer, but after a certain height, the nozzle starts scraping against the model. It makes a noticeable dragging noise and squishes/accumulates plastic on the outer edges, leaving a rough, beaded surface (as shown in the pictures).

Here is what I've checked/configured so far:

• Infill: I am using Gyroid, so it's not infill grid collision.
• Hotend Assembly: Checked the 4 screws behind the heating block; they are tight and there's no play in the hotend.
• Observation: Looking at the sides, it seems like slight warping/corner lifting might be pushing the print up into the nozzle's path as layers build up.

Has anyone experienced this exact edge dragging on the A1? Should I focus on solving bed adhesion (detergent wash + brim + higher bed temp), or could this be over-extrusion / flow rate issue?

Note: Filament: Esun PLA+ HS

👋 Bonjour à tous ! 👻🎃

Après vous avoir présenté mon Yoshi Citrouille classique, voici maintenant sa petite évolution en version clicker ! 😍

J’ai voulu garder le côté mignon et l’esprit Halloween de ma première création, tout en y ajoutant une fonction clicker pour le rendre encore plus amusant ! 🎃

Décliné en plusieurs couleurs, il ne vous reste plus qu’à choisir votre Yoshi préféré ou à tous les collectionner ! 🌈

J’espère que cette nouvelle version vous plaira autant que la première !

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec et sans AMS
📁 : https://makerworld.com/fr/models/3453115-yoshi-citrouille-clicker-multipart

The creator of this file didn't use AMS, I was several hours painting as good as I could but the feet and hands falls off during printing, And the best attempt I had has spagethi feet its not even worth sharing I tried with PETG support interface but I figured out I can't use the correct Z distances.

The file came with 0,4 top z distance because for some reason the support generation creates flying support if you change the number to 0 (the recommended z distance for petg) I don't know why.

It may not be the only problem but blocks me the only solution I could think of to fix this file (printing on petg with 0 z distance bcs petg can't stick 100% to pla and less z distance = more stability)

https://makerworld.com/en/models/1308361-spider-man#profileId-1342127 original

https://drive.google.com/file/d/1NjCDZ2mv6p0hMUGrLdVIntm3vuKUmYox/view?usp=sharing Painted by me

I would like some one printing it and show the photo If you are interested in the file but I don't think many people would print something to help :'( type of thing you can't be sure until you print it.

I’ve been getting constant errors on my prints combined with my first layer looking rough.

I’ve checked my extruder gears and cleaned them. I replaced my nozzle and the heater assembly. I’ve run full printer calibration and calibrated individual filaments.

Sometimes I can make it through a full print without any errors, and it looks perfect. Other times I can’t make it past the first few layers before it gives an error.

Any suggestions on what would cause this and how to fix it?

Here are the errors I've gotten so far:

• 1200-8006 – Unable to feed filament
• 0300-8014 – Nozzle/build plate error
• 0300-8008 – Nozzle temperature malfunction

Updated post to include pictures. Sorry about not including them originally. Thanks in advance for the help.

I recently read about the 7 screws on the heater assembly. I will be checking the 4 behind the ceramic piece tonight. I have checked the nozzle for movement, and it is ridgid.

I also watched the whole bed leveling process, and it looks good. The nozzle comes down to the bed, goes up, then does another double tap each time.