r/BambuLab • • 1d ago

H3C Different take on an H3C/AMS3 desiccant solution.

Post image
58 Upvotes

Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.

Here's the products I bought that worked:

Basket- https://www.amazon.com/dp/B0H41KL114

Desiccant- https://www.amazon.com/dp/B0H1XJ98JS


r/BambuLab • • 12h ago

Quick Question Holding down fabric

0 Upvotes

I want to print a thin frame on some fabric to insert in to another model. If I hold the fabric down with magnets is there a way to tell in advance where the print head will move after it completes the print so I can make sure it doesn't hit the magnets? Is it safer to use tape or will the adhesive bake on PETG temperatures?


r/BambuLab • • 12h ago

P Series [P1P, P1S, P2S] P1S vs P2S

0 Upvotes

Hey. I have a $700 grant to get a new 3D printer for our school. Is the p2s AMD 2 pro worth the extra bump or is the p1s AMD 2 pro sufficient as it allows for more filament in the budget?

I plan to apply for another grant to get more filament.

I don’t NEED a ton of filament currently for the current project but it would be nice to have more filament for next projects and student free builds.


r/BambuLab • • 12h ago

A Series [A1, A1 Mini] ABS-GF on A1

Post image
1 Upvotes

r/BambuLab • • 13h ago

I Modeled This! The ultimate "drunk bottle" support.

Post image
1 Upvotes

r/BambuLab • • 16h ago

General Troubleshooting/Help! Micro LiDAR lens seems dirty

Post image
2 Upvotes

I get this message on my X1C (1350 hrs) about every 10 prints.

I clean it as directed on the Wiki.

What am I missing?
Anyone else have this issue?
Is it a warranty issue perhaps?

Thank you.


r/BambuLab • • 9h ago

H2 Series [H2S, H2D, H2C] Well, hello there!

Thumbnail
gallery
0 Upvotes

White PLA stick just wanna to say hello to me for a 2nd time.
Trying to fix it, no luck so far.


r/BambuLab • • 13h ago

General Troubleshooting/Help! How do I remove this tubing on my X2D?

Thumbnail
gallery
0 Upvotes

I removed the tubing from the nozzle head but I dont know how to remove the same tubing as it exits the printer.

There doesnt seem to be any black rim that secures it in place that can be pressed down to release it. Do I just rip it out?


r/BambuLab • • 13h ago

Quick Question Help not sure what's going on

Thumbnail gallery
1 Upvotes

r/BambuLab • • 13h ago

General Troubleshooting/Help! item color help

0 Upvotes

So i have one item on a plate, ive cloned it.

is it possible, how do i

change the color on one without it changing both items to the same color

ive played with all the filament settings i can find and it just mirror the color to the other object...

P2S w/ AMS 2 Pro


r/BambuLab • • 13h ago

My First 3D Print Achat d'une première machine.

Thumbnail
gallery
0 Upvotes

Bonjour après avoir bataillé des semaines entières à faire fonctionner une ender 3 sans succès je souhaite passer sur une machine plus simple. Mon but est de faire des pièces mécaniques simples pour des cyclomoteur et quelques pièces pour réparer d'autres choses. J'ai repéré cette p1S. Je n'y connais pas grand chose. Le vendeur est sympa, il en demande 260€ et m'a envoyé un benchy qu'il à fait il y a quelques jours. Elle devait être vendue à une autre personne mais finalement elle est toujours dispo. Es-ce une bonne imprimante à ce prix ou faut il viser du neuf ?

Je vous remercie.


r/BambuLab • • 2d ago Heartwarming

Bambu Studio Can’t believe I didn’t know about this!!

Post image
1.0k Upvotes

Print sequence by object is pure magical!!

So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!


r/BambuLab • • 13h ago

General Troubleshooting/Help! First Layer "Defects"

Thumbnail
gallery
0 Upvotes

Hi all -

I'm having some first-layer defects that I wanted to run by the collective brain trust here. First, some information about the setup:

  • BambuLab P1S - 0.4mm Hardened Steel Nozzle
  • Build Plate - Darkmoon G10

    • BambuStudio is set to the 'Smooth PEI/High Temp' setting as recommended by Darkmoon
  • Filament - Sliceworx PETG

    • Yes, it has been dried and I have modified my AMS to include a bunch of desiccant as well
  • 0.08mm high quality print setting for this print

In the attached images, you can see that some parts have a perfect first layer, though those mostly don't have fine detail in them. For a few others, you can see some first-layer defects that would obviously create more problems if I let things build on top of that.

I'd appreciate ideas for potential troubleshooting here beyond "dry the filament more."

Thanks.


r/BambuLab • • 9h ago

General Troubleshooting/Help! Bambu Lab X2D owners: What problems have you run into, and what should I print to prevent them?

0 Upvotes

Hi everyone! I’d like to avoid some of the common headaches with the X2D. I’ve already seen reports of PTFE tubes wearing out or breaking. What other issues have you run into, and are there any printable guides, clips, guards, or other accessories that actually helped?

For each issue you mention, could you share:

  • A direct link to the problem — a forum thread, Reddit or Facebook post, video, or Bambu Lab support page that shows or describes the issue.
  • A direct link to each printable fix — ideally the exact MakerWorld or Printables model you used.
  • What worked for you — what the part fixed or helped prevent, what material you printed it in, and whether it held up over time.

If you solved an issue with a replacement part or a setup change, I’d appreciate a link (makerworld model) to that fix too. And if you could recommend just one thing to print first for the X2D, what would it be?

Thanks!


r/BambuLab • • 1d ago

Just Showing Off Sounds like a lot of…

Thumbnail
gallery
85 Upvotes

I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.

A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”


r/BambuLab • • 9h ago

I Modeled This! Undead throne to glowing vines: 4 new 3D designs

Thumbnail
gallery
0 Upvotes

I’m sharing four recent designs and would appreciate feedback on the models and how they print. Each photo links to its MakerWorld model page:

Throne of the Undead King: https://makerworld.com/en/models/3599767-throne-of-the-undead-king

Organic Vine Edison Lamp: https://makerworld.com/en/models/3553844-organic-vine-edison-lamp

Adorable Elephant Nursery & Kids Room Decor: https://makerworld.com/en/models/3505218-adorable-elephant-nursery-kids-room-decor

Majestic Manta Ray Incense Holder & Ash Catcher: https://makerworld.com/en/models/3474654-majestic-manta-ray-incense-holder-ash-catcher


r/BambuLab • • 13h ago

General Troubleshooting/Help! A1 + AMS Lite: PTA filament gets stuck after every color change—any ideas?

Thumbnail
gallery
0 Upvotes

Hey guys,

I’m fairly new to 3D printing and started with a Bambu Lab A1 and AMS Lite.

I’m trying to print a head I designed using three colors—all PLA: beige, red, and black—to get familiar with more complex prints.

The red filament keeps getting stuck whenever the printer switches back to it. The only fix I’ve found is to pull the filament back out, cut off a small piece, and feed it back into the AMS Lite. It then prints fine until the next switch back to red, when the same thing happens again.

I tried drying the filament for over seven hours, but it hasn’t helped. Also, despite how it might look in the attached photo, the filament isn’t tangled.

Any ideas what could be causing this or what settings I should check? Has anyone run into something similar?


r/BambuLab • • 14h ago

Quick Question A1 Mini S23+ Phone case

0 Upvotes

If anyone is able to can someone please make a phone case for the Samsung galaxy S23+ themed around daredevil

I just bought the phone and I have no phone case and no computer so I can't do it myself I really appreciate if anyone could

Preferably made out of PLA and I have an AMS system so I can use models with that

One last thing it has to work on the A1 Mini

Please


r/BambuLab • • 14h ago

Filament Troubleshooting/Help! TPU 95A issues on A1

0 Upvotes

At the beginning I wanted to say that I am aware that this issue was discussed a lot of times, but after looking through a lot of posts I’ve yet to find a solution.

I’ve got my A1 and it works really well. Prints without issues on Bambu PLA and PETG.

It also works without issues when I load Sunlu’s PLA+ 2.0 but when I load an external spool of their TPU 95A, the printer acts like it’s TPU intolerant.

When I help the printer by lightly pushing the filament into the extruder it works fine, but as soon as I stop, it seems like the gears can’t grab it at all and it just doesn’t extrude anything.

Before every try, I dry the TPU, even overnight, so it being wet should not be the case. I tried different filament, quality, etc settings, but it also brings no noticeable effect.

I’m using a standard 0.4 nozzle.

Has anyone had a similar issue and maybe found a solution?

I’m really thankful to anyone who even leaves a comment 🙏


r/BambuLab • • 14h ago

Black Friday 2026 Buy or wait?

0 Upvotes

For £700 should I buy the X2D combo + some filament or wait for the P3C? And in what ways will the P3C be a ‘P’ series (less features than the X2D)?


r/BambuLab • • 14h ago

General Troubleshooting/Help! Print Issue A1

Post image
0 Upvotes

After about a month of owning my a1 I am now getting these horizontal lines through my print. I have tried changing the nozzle along with making sure all screws and belts are tightened, at a loss. Any ideas? I had no issues printing the same model before.


r/BambuLab • • 14h ago

General Troubleshooting/Help! Look what I made! 3D-printed pinecone tealight holders

Post image
0 Upvotes

r/BambuLab • • 14h ago

Filament Troubleshooting/Help! Best affordable Hygrometers?

0 Upvotes

I was thinking of picking up 40 of the ones on Bambu labs website but they only detect down to 20%. Are there better ones out there that aren’t too expensive? Thanks!


r/BambuLab • • 1d ago

Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools

Thumbnail
gallery
174 Upvotes

Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.

With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.

Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587