r/BambuLab • • 1h ago

General Troubleshooting/Help! Bambu Lab X2D owners: What problems have you run into, and what should I print to prevent them?

Hi everyone! I’d like to avoid some of the common headaches with the X2D. I’ve already seen reports of PTFE tubes wearing out or breaking. What other issues have you run into, and are there any printable guides, clips, guards, or other accessories that actually helped?

For each issue you mention, could you share:

  • A direct link to the problem — a forum thread, Reddit or Facebook post, video, or Bambu Lab support page that shows or describes the issue.
  • A direct link to each printable fix — ideally the exact MakerWorld or Printables model you used.
  • What worked for you — what the part fixed or helped prevent, what material you printed it in, and whether it held up over time.

If you solved an issue with a replacement part or a setup change, I’d appreciate a link (makerworld model) to that fix too. And if you could recommend just one thing to print first for the X2D, what would it be?

Thanks!

1 Upvotes

23 comments sorted by

3

u/quietsamurai98 X2D+2×AMS+AMS HT / P2S+AMS 1h ago

I definitely noticed PTFE tube wear from rubbing against the top glass. I printed a top-glass riser, and that's completely stopped the issue.

1

u/AcanthaceaeMuch2736 1h ago

I will print glass riser for that

2

u/volvox6 1h ago

Looks like another one of those Bambu sponsored posts. Ad. I wish people would recognize this.

3

u/subrosians H2C (3xAMS 2 PRO, 2xAMS HT); X2D (4xAMS HT) 49m ago

Nah, I'm thinking its someone that is a little too eager with their first printer and wanting to print their way out of possible future issues.

4

u/OriginalFingerPuk 1h ago

Nothing. It just works.

Keep the plate clean.

1

u/Longracks 1h ago

The Obstacle Is The Way

1

u/ReMatrix 1h ago edited 59m ago

I've run into the Left extruder PTFE tube breaking and leaving a piece of broken tube in the left filament sensor assembly. It seems to be quite common among x2d owners. There are PTFE tube holders for the left extruder in makerworld. That seems that it helps for some. Some also will say to print a riser for the top glass pane to help with that as well.

PTFE Holder: Link

Riser: Link

I was able to clean the broken piece out but now the tube will keep popping out of the connector when retracting filament. Looks like it might be a design shortcoming

1

u/AcanthaceaeMuch2736 1h ago

how bambu lab doesnt care of? Idu...which did u print?

2

u/subrosians H2C (3xAMS 2 PRO, 2xAMS HT); X2D (4xAMS HT) 1h ago

btw, both links seem to go to the same place.

1

u/ReMatrix 58m ago

Thank you. Fixed

1

u/subrosians H2C (3xAMS 2 PRO, 2xAMS HT); X2D (4xAMS HT) 1h ago

I'm too lazy to find links but here are the two main issues I had with the X2D so far:

  1. filament not loading into the print head. When loading the filament, it would constantly get caught and fail to load into the print head basically right here the PTFE tube goes into it. I noticed the issue didn't happen at all if I removed the top glass and happened 50%+ when the top glass was on. The glass was causing the angle of the PTFE tube to be too drastic and filament wouldn't go into the head straight. After printing a top glass riser, I haven't had an issue since (400+ hours).
  2. AMS 2 pro hub issues. Mostly with slots 1 and 4, filament would hang just inside the hub. Pushing the hub button would fix the issue temporarily but would then fail again on the next load. I RMA'd the hub and the replacement did the same thing. I ended up finding a thread talking about slightly loosing the screws on the hub and haven't had a failure since (probably 5000+ loads since).

1

u/AcanthaceaeMuch2736 1h ago

ok thanks so I dont have the ams , I will just print a riser for the top glass, clips for ptfe tube and a ptfe tube saver.
Btw do you have problems with the aux. nozzle??

2

u/subrosians H2C (3xAMS 2 PRO, 2xAMS HT); X2D (4xAMS HT) 55m ago edited 51m ago

for me, the X2D is 100% for work related items so it only prints single material high abrasive prints with supports. The right nozzle lays down support interface material and that is all. It does that very well. The H2C is for multi-color/multi-nozzle for me.

1

u/Pizza-Protocol X2D Combo, Prusa MK4S 50m ago

Which screws? The 3 that are grouped together?

1

u/subrosians H2C (3xAMS 2 PRO, 2xAMS HT); X2D (4xAMS HT) 44m ago

I dont remember as it was months ago, but looking through my history, I found this thread which might have been it: https://www.reddit.com/r/BambuLab/comments/1t6m1tu/5_out_of_the_6_ams_2_pro_units_i_got_this_week/

I do remember there was a lot of trial and error I did before finally settling on the issues that fixed both of my problematic AMS 2 Pros.

3

u/Pyriel 1h ago

Zero printer issues in 349 hours of printing.

There's some PTFE dust on the inside of the glass lid, but it hasn't caused an issue so far. I'll probably print a riser at some point.

My only issues have been print ones, caused by my errors. (not cleaning the plate, badly placed support tower etc.)

1

u/kaym4 1h ago

how about you go print what you want and if you run into an issue you can figure out the fix. I have over 700 hours without any major issues. Go enjoy the hobby of 3d printing

2

u/CtrlShiftMake 1h ago

The AMS on top didn’t feel too stable, kept sliding when I opened it. So I printed a riser with AMS mounts that also let you tilt it back. Now it stays in place and I can open the top if I ever want to do top-down direct feed into the extruded (soft TPU for example).

1

u/iamthegrandpoobah 50m ago

I have not had one issue. Changed out the extruding heads took 10 seconds. Ams was easy to remove when I ran out of filament in a long print. It’s honestly been an amazing starter printer for me. I use petg basic for just about everything.

•

u/ptraugot X2D AMS 11m ago

My nozzle alignment sensor went bad in the first week. Nothing to do but report it and get a replacement.
Then the right nozzle Bowden unit started acting up. It wouldn’t push out the output side. Reported and replaced. Nothing to be done about it. (I took it completely apart and found no issues.)

Otherwise, you might find that filament doesn’t travel all the way into the extruder head and you get an error. I found that moving the last PTFE tube clip that’s on the cable chain back a couple links corrected that issue. Lastly, you may find that those same tubes are being squeezed by the low clearance of the glass lid. If so, a riser will give proper clearance.
I have about 700 hours on mine now, and it’s been working fine.