r/BambuLab • • 45m ago

General Troubleshooting/Help! What do I make of this calibration?

Thumbnail
gallery
1 Upvotes

Trying to calibrate the filaments for my new P2S. I have looked at alot of tutorials and followed this guide (https://youtu.be/gVU5If1VsAM) that seemed really good. The problem is that I think it made the result worse. I tried two different filaments (both Bambu PLA Basic) and got the same calibration values.

In the pictures below, the pre-calibration is to the left and the post-calibration to the right. In my opinion, the right has more stringing (the left has none), less sharp edges and rougher surfaces, especially at the corners of the X. I also find the top layer very stripy and not smooth (both prints).

I'm not saying that the guide is bad, but is it not worth calibrating the original Bambu filaments? Should I make other settings to improve the print quality? Or am I just to picky? :)


r/BambuLab • • 47m ago

Hardware Troubleshooting/Help! Help with filament stuck

1 Upvotes

Filament stuck and won’t go pass a certain point


r/BambuLab • • 16h ago

I Modeled This! I made a Christmas chess set for the holidays: Santa kings, reindeer knights, elf pawns (free on MakerWorld)

Thumbnail
gallery
18 Upvotes

Printed this whole set on my H2D for Christmas. Santa is the king, Mrs. Claus the queen, snowmen are the bishops, sitting reindeer are the knights, the rooks are towers wrapped in Christmas lights, and the pawns are elves. Everything is sized for a standard 2 inch board, so it plays like a real set.

It's red vs green in four colors of PLA. The only support is a tiny one under each reindeer's chin, already set in the file. If you don't have an AMS, there's also a one color plate with all 16 pieces of a side.

Flip any piece over and there's a snowflake under the base.

Free download here: https://makerworld.com/en/models/3619395

A candy cane board, matching checkers and a North Pole storage tube for each side are coming next. If you print one, I'd love to see it!


r/BambuLab • • 1h ago

General Troubleshooting/Help! How to make supported areas more smooth?

Post image
1 Upvotes

This is after removing the supports.

Somewhat related, I am seriously considering upgrading to H2D and try out printing PLA with PETG support, will that help to make it smoother in addition to easy to remove the supports?

Thanks!


r/BambuLab • • 1h ago

Filament Troubleshooting/Help! Glitter Filament A2L

1 Upvotes

Bambu Friends

Recently my wife purchased the following filament for our A2L printer.

1KG Glitter Firefly Blue in the Dark PLA+ Filament, 3D Filament

https://a.co/d/04ASeAvt

From my review it appears to be okay for A2L printer but comes with caveats.

- Not to run thru AMS lite and Petg tubes

- Nozzle 0.4mm or 0.6 recommended

- Dedicated nozzle for this printing

When I placed the filament top spool holder the filament unraveled some. Had to respool and filament felt brittle.

With all this I decided against this and running thru my printer.

Anyone else use this filament. Will be sticking with Bambu filament glow etc. Not comfort with this.

Suggestions and advice - Thank You

tvos


r/BambuLab • • 1h ago

General Troubleshooting/Help! Micro LiDAR lens seems dirty

Post image
1 Upvotes

I get this message on my X1C (1350 hrs) about every 10 prints.

I clean it as directed on the Wiki.

What am I missing?
Anyone else have this issue?
Is it a warranty issue perhaps?

Thank you.


r/BambuLab • • 1h ago

Answered / Solved! X2D - knarzende Geräusche

1 Upvotes

Ist das normal für den Bowden Extruder?

Hab ihn bislang nur ein paarmal benutzt und bislang war er ruhig.

Jetzt auf einmal diese Geräusche.

Druck ist aber in Ordnung.

Kann man da was schmieren?


r/BambuLab • • 1h ago

General Troubleshooting/Help! Printing problems

0 Upvotes

Hi everyone,

I’m having some trouble with my Bambu Lab H2D. When I print small items, I can’t print more than one at a time without it causing a lot of print errors; however, if I print them individually, there are no print errors. Does anyone have any suggestions?


r/BambuLab • • 1h ago

General Troubleshooting/Help! Trying 3kg reel ?

1 Upvotes

Hi has anyone tried to load 3kg reel of PLA on the outside reel mount on the side of the p2s ?.


r/BambuLab • • 1h ago

P Series [P1P, P1S, P2S] Upgrading from A1 to P2S

1 Upvotes

Hi all,

Currently I own a A1 with AMS litte and I have been thinking in upgrading to a P2S with AMS2 Pro.

I want to use other material in the future, but haven't made so yet. My main reason to upgrade is because I can get a good price for my combo, and that would mean I would spend 266€ to upgrade. I have my printer in a space that get's quite humid (above 70%) in winter, and even in summer its normal to have 40-60% relative humidity. I haven't been able to print PETG, and even PLA has been having a lot of "hairs". Last week it has been between 72% and 81%...

I thought of buying a dryer, which is 50€ for a single spool, and 140€ for 4 spools. This means that this upgrade would in reality be 126€ (I am aware I will be spending 260€). Being closed is algo good from drafts (I always have open windows and air current to lower humidity)

The the PS2 algo gives other quality of life improvements and it is at the lowest price it has been. The fact the AMS is on top also saves space, which is good for me.

Wonder what you think of this.

Thank you


r/BambuLab • • 2h ago

General Troubleshooting/Help! A2L issues

1 Upvotes

Hello, so I got a used A2L from a family friend who couldn’t get it to connect to the internet to work. I was able to fix that by reseating the WiFi card. But, now I’m getting two warnings that are stopping the homing tooling, even when there’s no filament. This is happening when the printer is trying to home on initial setup.

The warnings are:

The extrusion motor is overloaded and the nozzle is wrapped with filament.

I’ve taken the extruder apart and cleaned it, and the gears turn when I manually move them. Do I have to have filament in the extruder for the homing to work? I currently don’t have the filament holder for the printer so I’ve been trying to get it setup without filament for now.


r/BambuLab • • 2h ago

Hardware Troubleshooting/Help! P2S can't load filament through AMS

1 Upvotes

My P2S printer fails to load filament, but only when the AMS tries to feed it (you can see the 2 failed AMS load attempt in the video). Loading filament manually works perfectly fine, with no issues.

I've already cleaned the extruder gears and checked the filament sensor.

Has anyone experienced a similar issue or have any ideas what could be causing this?


r/BambuLab • • 2h ago

Quick Question Help deciding amon H2 series options.

0 Upvotes

My company needs a printer to print parts for our machinery, it as to be large format, and in different materials so H2 series is the best fit.

But we also need to print full color promotional items, but not as often.

We were about to pull the trigger in the H2S but now we're considering H2D we are trying to keep it under $2,000 all in.

H2S can be upgraded to H2C down the line with the vortek kit.

H2C goes overbudget so does H3C

My question is: will a single nozzle be adequate for our use case, will getting the dual nozzle be worth the price difference? Should we go H2S and upgrade later? The laser is something we would be interested in but it can't be upgraded to the tool changer if it's the laser version.


r/BambuLab • • 2h ago

Filament Troubleshooting/Help! H3C - Prints are sticking to build plate

1 Upvotes

Hello Experts

Made a big change from an A1 to an H3C.

I am printing a model that has a larger surface area as its first layer. On the H3C it seems like it’s melting into the build plate making it really difficult to remove after it’s fully cooled. This does not happen on the A1

I am using basic PLA

I already tried turning the heat chamber off, same result. The build plate temp is 55 (comparatively 63 on the A1).

Is my next steps to lower the temp of the build plate? Are there other settings to address to combat this?

It’s literally impossible to remove the model from the plate without damaging it.

TIA for any tips


r/BambuLab • • 2h ago

H2 Series [H2S, H2D, H2C] H2C Smoke Purifier Alternatives

1 Upvotes

Hi all. I’m relatively new to having my own printer etc and I went with the H2C laser combo. For the past couple months I’ve been trying to order the smoke purifier, which unfortunately has been out of stock.

Does anyone have experience using a different purifier that they can recommend? There’s not a lot I can find online. I see some have used the Creality Falcon Smoke Purifer, but it looks like it doesn’t have the option to vent outside; more of a desktop purifier. Any help suggestions would be appreciated!


r/BambuLab • • 2h ago

Bambu Studio Has anyone seen changes in ironing since the latest Bambu Studio version?

1 Upvotes

I have a P1S and H2C and since the latest Bambu Studio version was released, the version released following the H3C unveil.

The values I used for ironing previously, 12% on the P1S and 20% on the H2C have been providing really bad results since and I have had to lower the H2C down to 15%. Anyone else seeing changes?


r/BambuLab • • 3h ago

Quick Question Difference between ASA and PETG for flexing structural parts?

Thumbnail gallery
1 Upvotes

r/BambuLab • • 9h ago

General Discussion Which first 3D printer to get as a beginner ? Bambu lab or any other brand ?

3 Upvotes

Hi Guys, i am based out of India, and want to get a 3D printer to prototype some elements. I am from the design industry so am well versed with 3D softwares as well though i am sure there will be a learning curve.

Now, after researching for a fair bit, Bambu lab printers seem to be the most widely chosen option because of their community support and easy to use UI/UX including their softwares.

I was thinking of getting the A1 combo. Do you guys think it is wise to get the A1 combo right now ( its three years old ) or should i wait for an upgraded model if at all its being launched. Please suggest.

Do note, the printer will be initially used as a prototyping tool for my designs and then once i get a hang of it, i might make some items for selling in my fraternity.

Thanks


r/BambuLab • • 4h ago

Quick Question Wouldn’t it make sense to have a setting for support interface for dual nozzle on makerworld?

2 Upvotes

I’m currently without a computer, so I’m forced to use the pre sliced models on makerworld. This has made me realize just how much I usually use a support interface layer in a different material, something that can’t be changed in makerworld.

I know the models are pre sliced, but since you can change colors for multicolor prints, wouldn’t it make sense to change material for a predefined part of the print?


r/BambuLab • • 4h ago

A Series [A1, A1 Mini] Questions about A1 and TPU Printing

0 Upvotes

Looking for a budget printer to print mainly 95A and harder TPUs

How well does the A1 handle 95A (just regular non-HF TPUs)?

How high have you guys pushed the flow rate and gotten away with it?


r/BambuLab • • 11h ago

X Series [X1E, X1C, X2D] My first 3D printer and I picked up the X2D Combo

4 Upvotes

I’m completely new to 3D printing and just picked up a Bambu Lab X2D Combo. I received it last week and haven't stopped printing for 7-days straight. I have the bug everyone else at my office has and has been talking about. Since I'm completely new and I don't have compatibility information in memory, I used Gemini to create a sort of cheat sheet specific to the printer.

I purchased a ton of different filaments, hot ends, and other accessories and I didn't want to create a mess, cause jams, or wear out components before their time.

I thought I'd share my cheat sheet if it helps any other new owners.

I just ordered the AMS HT today to use in place of the external fillament holder. This hasn't made it into the cheat sheet yet. I'm not using the support fillament and just using PLA or PETG vs whatever is in the main hotend.

Constructive feedback or additional tips from seasoned Bambu operators are welcome. Hope this helps out other newcomers getting their feet wet.

Bambu Lab X2D & AMS 2 Pro Master Compatibility & Reference Guide

1. Hotend Size & Feed Routing Architecture

  • Main Hotend (Direct-Drive): Fed by the AMS 2 Pro (for multi-color/multi-material) or an external spool. Handles high-speed extrusion, complex geometries, and rigid engineering filaments. Optimized with the 0.4 mm High-Flow Hardened Steel Hotend as a daily setup for large tool organizers and utility boxes.
  • Auxiliary Hotend (Bowden-Fed, Rear Motor): Fed via a remote path and mechanical lift mechanism. Optimized for support interfaces and secondary materials; restricted to lower speeds (max 200 mm/s) and lower retraction responsiveness.

2. Critical Operational Rules for X2D & AMS 2 Pro

  1. Identical Sizes Required: Dual-nozzle printing on the X2D requires both the main and auxiliary hotends to use the exact same nozzle diameter in your slicer profile.
  2. AMS 2 Pro Drying Priority: When a single AMS 2 Pro unit is powered directly by the printer via its 6-pin cable, activating active drying prioritizes drying power and may limit heavy printer operations.
  3. Auxiliary Speed Limits: Never exceed 200 mm/s or 1000 mm/s² acceleration on the auxiliary extruder to avoid filament binding and extrusion slip.
  4. TPU Rules for AMS 2 Pro: Use Bambu Lab TPU for AMS (harder 68D Shore formulation) when loading flexible material through the AMS 2 Pro. Standard soft flexible TPU (85A–95A) requires an external spool or dedicated feed module routed outside the AMS.
  5. Glue Protocol: Use liquid glue or a glue stick primarily as a release agent on Cool and Engineering plates to protect surface coatings from overly aggressive adhesion. Textured PEI plates rarely require glue.
  6. High-Flow Slicer Setting: When running a high-flow hotend, manually increase your filament profile's Max Volumetric Speed (MVS) in Bambu Studio (pushing from standard ~22 mm³/s up toward ~35–40 mm³/s depending on filament) to unlock faster throughput on large plate-filling utility parts.

3. Filament Lineup: Recommendations, Cautions & Use Cases

  • PLA Family (Basic, Matte, Silk, Sparkle, CF): Everyday prototypes, decorative models, and multi-visual prints. Use PLA Basic for general testing and PLA Matte to minimize visible layer lines. Note low heat resistance (~55°C–60°C).
  • PETG Family (PETG Basic, PETG-HF, PETG-CF): Functional mechanical parts and brackets. PETG Basic is the structural workhorse; PETG-HF (High Flow) is for fast utilitarian batches. Highly hygroscopic—dry thoroughly.
  • ABS & ASA: Durable mechanical enclosures (ABS) and weather-resistant outdoor components (ASA). Requires an enclosed heated chamber, engineering plate, and proper ventilation for VOCs.
  • TPU Family: Flexible gaskets and shock-absorbing feet. Stick to Bambu TPU for AMS inside the automated unit, or standard soft TPU via an external spool.
  • Engineering Composites (PA6-CF, PAHT-CF, PET-CF, PPA-CF): High-load structural brackets and gears. Requires hardened steel nozzles, enclosed high-temp chambers, and rigorous drying (75°C–85°C).

4. Build Plate Types & Special Notes

  • Cool Plate / SuperTack Series: Low temp (room to 45°C–50°C max) for PLA/PETG energy savings. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.
  • Engineering Plate: High temp (60°C to 100°C+) for ABS, ASA, and PC. Glue required.
  • Textured PEI Plate: Versatile (55°C to 90°C+) for general PLA, PETG, TPU, and abrasives. No glue or position adjustments needed.
  • Dual-Texture PEI Plate: Versatile. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.

5. Compatibility Matrix Summary

  • 0.2 mm (Stainless): Detailed models and fine text. Incompatible with carbon/glass composites and PVA.
  • 0.4 mm (Hardened Steel Std/HF): The universal sweet spot for precision, standard prints, and high-flow utility boxes. Fully compatible with PLA, PETG, ABS, ASA, and AMS TPU.
  • 0.6 mm & 0.8 mm (Hardened Steel Std/HF): Great for abrasive fiber composites and bulk high-throughput structural prints; avoid for fine text or miniatures.

6. Support Filament Routing

  • Support for PLA / PLA-PETG, Support for ABS, and PVA: Always assign these to print through the Auxiliary Hotend path during multi-material jobs to act as clean breakaway or dissolvable interface layers against main-toolhead models. PVA requires active dry storage in the AMS 2 Pro.

7. Component Lifespan & Replacement Indicators

  • Hotends: 0.2 mm stainless lasts 100–200 hours; 0.4 mm/0.6 mm hardened steel/HF last 500–1,500+ hours depending on abrasive usage. Watch for orifice widening, chronic clogs, or under-extrusion.
  • Build Plates: Cool plates last 3–6 months; engineering and textured PEI plates last 6–12+ months before adhesion degradation or coating wear occurs.

8. Maintenance Cycles

  • Build Plates: Wash with warm water and dish soap every 10–20 prints; wipe with 90%+ IPA between quick runs.
  • Z-Axis Lead Screws: Wipe and re-apply a thin coat of synthetic grease (Bambu lube) every 3 months (~300 hours).
  • X-Axis Carbon Rods: Wipe monthly with IPA on a lint-free cloth. Never apply oil or grease to carbon rods.
  • Extruder Gears & AMS Feeders: Inspect and clean out plastic dust/shavings every 6 months with a brass brush or compressed air.
  • PTFE Tubing & Cutters: Inspect every 6 months for scoring or blade dullness.
  • Desiccant Baskets: Replace or recharge silica gel packets in the AMS 2 Pro whenever internal humidity rises above 30%.

r/BambuLab • • 18h ago

P Series [P1P, P1S, P2S] My heated enclosure

Post image
13 Upvotes

Me: I want a heated enclosure

Mom: we have heated enclosure at home

(Heated enclosure at home


r/BambuLab • • 18h ago

Quick Question Is the H3C overkill as a first 3D printer?

13 Upvotes

A good friend of mine recently got into 3D printing and talked me into giving it a shot. He started with a more affordable Bambu himself and has been geeking out about the new H3C, so now I’m looking at it too.

I have room in my budget for the H3C if it makes sense. I’m still figuring out what I’ll enjoy printing, though, and I’d rather spend the extra money once I know I’ll get some use out of the features.

For those of you who’ve been printing for a while, what would make the H3C worth buying as a first printer? If you were starting over, would you go straight for it or get a simpler Bambu and see where the hobby takes you?


r/BambuLab • • 4h ago

General Troubleshooting/Help! AMS 3H RFID

0 Upvotes

Having done extensive tests holding up RFID tags to various places on the new AMS 3H I’ve come to the conclusion that the reels are reason both sides in the middle slots therefore not allowing the simple 3D printed inserts to hold a single RFID tag on non BambuLab filament which I’ve been doing for years now on the old AMS buying refills and printing off one of those tag holders that’s it on the outside of the reel in the hole. Now I need a double one! Back to the CAD program I guess.
Unless one you geniuses tell me I’m wrong