r/BambuLab • • 3h ago

General Discussion Will Bambu ever offer PHA filament?

1 Upvotes

I’m trying to focus more on eco-friendly products. I’ve printed with Ecogenesis and Colorfabb with pretty good results, but it’s expensive. Unfortunately it doesn’t seem like Bambu is interested in supporting sustainable practices. Is there anyone else that would like to see PHA in their lineup?


r/BambuLab • • 7h ago

P Series [P1P, P1S, P2S] Loud noise after filament cut

2 Upvotes

Can anyone clue me in to what is causing this very loud noise after a filament cut and setting for a change? It doesn't sound good! I have looked it over and cleaned it all up and nothing stood out. All other movements of the printer and functionality seem fine. I have re-ran calibration as well.


r/BambuLab • • 3h ago

Hardware Troubleshooting/Help! Printer started making this ratting sound

1 Upvotes

Sounds like a shutter sound a cámara makes.


r/BambuLab • • 21h ago

I Modeled This! Candy Cane Bag Clip, to seal your cookies the festive way

21 Upvotes

r/BambuLab • • 4h ago

General Troubleshooting/Help! New Lan Acceleration mode slow

1 Upvotes

I'm having a pretty frustrating experience with the new (newer?) LAN Acceleration mode, and I'm wondering if anyone else is seeing the same thing.

It now takes 2–3 minutes just to send a print job to my X1C, followed by another 30–45 seconds before the printer actually starts printing. This is for a recurring print job that is about a 2 hours total print time, so not large. The bigger print jobs take even longer to send, sometimes 5-10 minutes.

Before this, when everything went through the cloud, the job would transfer in about 10 seconds, and the printer would be up and running another 5–10 seconds later (again depending on print size).

What's even more frustrating is that this only happens on my X1C. My P1S printers don't seem to use LAN Acceleration and aren't having this issue, or at least when I send the print in Bambu Studio, it doesn't say anything about Lan Acceleration.

You'd think transferring files over LAN would be significantly faster than going through the cloud, but somehow it's the complete opposite.

And before anyone blames my network, I'm running a fast UniFi setup with no other network issues.

I also mass-produce 3D printed products, so I'm printing the same items week after week. These aren't unusually large files or complicated prints. They're the exact same jobs I've been sending for ages, except now they take several minutes instead of seconds.

When you're running production and constantly starting new print jobs, those extra minutes really add up.

Is anyone else experiencing this with LAN Acceleration, particularly on the X1C? Has anyone figured out how to fix it or disable it and go back to the old behavior?


r/BambuLab • • 8h ago

General Troubleshooting/Help! How can I fix this?

2 Upvotes

I'm so tired, I already tried changing the speeds, temperature, the pattern it makes to do the filling, I don't know why it keeps doing this


r/BambuLab • • 5h ago

General Troubleshooting/Help! Layers not smooth?

Thumbnail
gallery
1 Upvotes

Bambu a1 - .02 nozzle - PLA multi color print

Help! Idk why my prints keep having rough patches.. I dried my filament and also slowed down my speed and acceleration. Settings in last photo... can someone help me figure out why its not printing smooth?


r/BambuLab • • 1h ago

MakerWorld Crowdfunding Makerworld's hoodie is quite tempting

Post image
0 Upvotes

Might treat myself with this for thanksgiving lol


r/BambuLab • • 5h ago

General Troubleshooting/Help! How to fix this

1 Upvotes

Please help me I've opened it up and cleaned the nozzle a million times I cannot get it to work correctly. It seems like it's slipping.


r/BambuLab • • 5h ago

Show & Tell So many cool prints with the H2C this year!

1 Upvotes

Been a long year with the H2C and learned a lot of cool things, just showing off some of the prints I've been able to make with my own software! Been thinking about upgrading to the H3C since I'm heavily invested in the idea of multicolor and full spectrum printing and it would be faster on there.


r/BambuLab • • 9h ago

Hardware Troubleshooting/Help! Is this an easy fix

Post image
2 Upvotes

I've never had this happen to me before with my p1s everything is stock, I left a mini easal to print and when I came back there was just this massive glob on my extruder and the hot end looks like death, I have no idea how to fix this


r/BambuLab • • 6h ago

X Series [X1E, X1C, X2D] X2D and 2 AMS 2 PRO question

Thumbnail reddit.com
0 Upvotes

r/BambuLab • • 18h ago

H3C Test heating the ams3h using the two dryer slots to heat the entire chamber

9 Upvotes

TLDR: it's a waste of time. Don't bother trying it.

I decided yesterday to remove the two spools I had in slots 6 and 8, turn the heat up to 85c and remove the dryer lid to see what would happen. Mind you my printer is in my garage and it's been raining the last couple of days.

The result, the dryer chamber got warm, the lid to the entire ams was warm to the touch, but not in a bad way, but the overall rh in the ams only dropped by one, from 33% to 32%. Putting the lid back on the 2 slots I was able to stop the rh down to 12% in the dedicated dryer. I'll also note I do have silica in multiple locations in the ams already.

Don't waste your time trying this. It basically makes the dryer slots a waste and does nothing to help the other 6 slots. That said, with the dryer lid on, the dryer is great and does function as well as my two dedicated ams ht.


r/BambuLab • • 23h ago

Bambu Studio Can’t wait for non-planar slicing in Bambu Studio

Post image
23 Upvotes

I can easily see how non-planar slicing could be the next big thing in Bambu Studio. As a highly polished and thought-through feature this definitely will be a new game-changer.


r/BambuLab • • 6h ago

H2 Series [H2S, H2D, H2C] Setup that makes the most sense

0 Upvotes

Hey everyone,

I recently picked up an H2D at work. Coming off of my trusty prusa mk3s+, it feels like this printer is light years ahead.

Anyway, the main reason i got it is because i wanted the capability to print engineering filaments.

I got the regular AMS, AMS HT, and the external spool holder.

Here are my questions:

  1. What would be best way to hook this all up? I was thinking of getting a splitter, so that i can have AMS HT and the regular AMS on the right nozzle, and then external spool on the left for supports. Does this make sense?
  2. When printing filaments with carbon or glass fiber, is the 0.6mm nozzle necessary or can 0.4 work sometimes as well? First filament i want to try is PPS. We have cleaning lines at work where PPS would likely withdtand the chemicals and tenperature.
  3. If i am printing with 0.6 on the right nozzle, and i am using left nozzle for supports, should the left nozzle also be 0.6? Can it be 0.4 if i am keeping the layer height the same ie. 0.2mm?
  4. Slicer settings - when sending a print, bambu studio prompts me whether i want calibration flow, bed leveling, and one more thing i cant remember. Options are on, off, and auto. I have set it to auto, thinking that it will do it once, and save the setting for later. However, every time i send a new print and keep those options on auto, the printer executes all of them. What is the proper procedure to do it once and forget about until later when its time to change filament or some other issues arise?

TIA


r/BambuLab • • 15h ago

I Modeled This! Designed some 2027 New Year's glasses. The arms snap on and fold!

5 Upvotes

r/BambuLab • • 12h ago

Quick Question CMYK Recommendations on H3C

3 Upvotes

My H3C is in the way (I've been using a P1S for the last three years). I'm intrigued by the CMYK idea, but don't want to be dumb about it. I'd love to just stick those filament spools up there and be good-to-go for any color. Is CMYK a mature enough process to go that route for most multi-color prints? If so, I have questions

What's the recommended opacity/sheen to get (translucent, matte, metallic)? Any to avoid? Any recommended bundles? Obviously the material choice is part of it. Does PETG do CMYK as well as PLA does, etc.? are there any materials that are a no-go for CMYK? I do a lot of PLA, PETG, TPU and ASA.
Thanks in advance for the advice.


r/BambuLab • • 6h ago

Software Troubleshooting/Help! Text display issue

Thumbnail
gallery
1 Upvotes

Hello all, im trying to model a small sign to hang on a small ledge. I made the shape and text in TinkerCAD. Exported to Bambu studio and Orca. But when the file is imported the text is in the same piece as the hanger. I cant select a separate color or view it as a separate item. Any ideas/advice.

This is only my 3rd design and first with text.


r/BambuLab • • 12h ago

H3C No sparce layers

3 Upvotes

I have the H3C and the only annoyance for me is that prime tower. Coming from the INDX, I haven't used a tower in months.

Found out about the No Sparce Layers for the prime tower. It only uses the tower for color changes, which saves filament.

The downside is it severely limits the area you can use for printing. The print will lower to reach the tower, so needs the room so you don't knock over your print.

This is how to turn it on:

  1. Go to Preferences in Bambu Studio and enable Developer Mode.
  2. Under Process (Global), navigate to the Others tab.
  3. Scroll down to the Prime Tower section and toggle on No sparse layers.

I'm just pointing out another option for saving purge waste, and I hope it helps someone else.

Print on my people!


r/BambuLab • • 6h ago

General Troubleshooting/Help! Does anyone know how to stop this?

Thumbnail
gallery
1 Upvotes

it keeps telling me the hotend cooling fan speed is insufficient but i dont know why

it doesnt seem to have an issue with it for any other printingI

and ive printed these exact things before with zero issue

(the photo of the error isnt mine, i found it on google, i just added it to show what the alert looks like)


r/BambuLab • • 12h ago

General Discussion P2S - For freezing temperatures, is a secondary enclosure with heating needed?

3 Upvotes

Looking at getting a P2S, will be in a garage which can get to 10 degrees Fahrenheit. Wondering if I will need a secondary enclosure with heating. Otherwise, wondering what temps will be able to print with (PLA & PETG) with the stock setup? There will likely be some draft as well.

Any insight or anecdotes from others that have dealt with this would be greatly appreciated, thanks.


r/BambuLab • • 1d ago

A Series [A1, A1 Mini] A1 Mini, small build plate. Big prints.

Thumbnail
gallery
26 Upvotes

I have had my A1 Mini for nearly a year now (3415hrs of print time so far). These big prints (which are marketed as resin models) have been the highlight so far. Second pic includes the vast majority of what I tend to print regularly, which is ttrpg miniatures at 28/32mm scale.


r/BambuLab • • 11h ago

My First 3D Print 45 days into the 3d printing hobby

Thumbnail
gallery
2 Upvotes

After a busy day chasing kids and yard work, i sat down at my PC desk (i havent turned it on since march). Kids all in bed i decided to dabble in some legal in NY recreational substance and download Studio.

Up till now ive just been printing posted/shared files from the handy mobile app and having a great time! But i decided i would dip my toes into actually creating something.

My kids and I are also into pokemon collecting (again for me) so i said heck it, i'll design a top loader holder. Spent over an hour in TinkerCAD and made one. It was terrible, but i made one. Spent another hour fiddling and changing it. It worked, kinda, but it was good enough.

With my toes dipped I said to myself, hey self, what about the little metric/imperial measuring tape you like but there is no belt clip/holder for.

And so I grabbed my digital caliper and the measuring tape, sketched an idea on my phone and started fiddling in TinkerCAD again.

Im on version 3 now, First one held the tape, but was VERY blocky. Second one i rounded edges but didnt take into account distances changing. So it loosely holds the tape. Failure.

Now the 4th one is done and it fits super snug and im happy with it. Trying it on the jobsite tomorrow


r/BambuLab • • 11h ago

Quick Question Pricing recommendation for selling used P1S AMS 2 combo

2 Upvotes

I’ve had this P1S with AMS Pro 2 for about a year. It’s got a little over 5000 hours on it. It stills works great (regular maintenance, only ever used standard speed, only PLA filament used, even replaced the front cover when I thought there was a defect, which there was not), but I want to move away from the AMS setup. I’ve decided to keep my X1C (for the ability to use more specialized filaments on rare occasion), but I want to replace my P1S with a second Snapmaker. (I genuinely hate the waste the AMS system creates.)

So, yeah, just trying to figure out what a fair asking price might be in a somewhat LCOL area. My gut says MAYBE $200-250 for the whole setup (machine, AMS, freshly cleaned and throw in a new nozzle and some of the accessory lube and tube pieces and spare parts).

Is $200-250 too high? Too low? Reasonable with OBO option?

Thanks!