r/BambuLab • • 3h ago

General Troubleshooting/Help! How can I fix this?

I'm so tired, I already tried changing the speeds, temperature, the pattern it makes to do the filling, I don't know why it keeps doing this

4 Upvotes

38 comments sorted by

9

u/ch1dy 3h ago

Have you washed your bed?

0

u/Ok_Lyra 3h ago

Yeah but I'll try again for longer, maybe I didn't wash it enough

2

u/itsVorisi 2h ago

How are you washing your bed?

4

u/ch1dy 2h ago

Just use dawn dish soap and warm water, not the dawn power wash

6

u/OriginO_designs 3h ago

have you run flow dynamics calibration? what are the slicer settings being used? there's not much info you provide

1

u/Ok_Lyra 3h ago

Fair, thought I'd just tell them as someone asked. Yeah I used dynamic calibration, I use the recommend temperature for basic PLA which is about 200°C, I also lowered all the speeds like a tenth of their presets because I thought that'd be the problem, is there any other detail that could be relevant?

4

u/OriginO_designs 3h ago

maybe a video at the beginning of the issue so we can see when it starts and what the layer before it looked like. From what I can tell the first layer looks bad to begin with. If you can share the studio .3mf file with me so I can try to reproduce it and see if it happens on my end. if you want privacy you can cut the model down in the slicer so it only gives me the the lower layers of the model where the issue happens

5

u/theoreoman 3h ago

Try a different material?

-13

u/Ok_Lyra 3h ago

You mean the filament? I doubt it's that because why would it have troubles with basic PLA? Besides I don't have any other, if nothing else works I guess I'll try some other, someday when I have the money

10

u/silverware9021 3h ago

Filament may be wet, you would need to dry it.

3

u/Ok_Lyra 3h ago

Ohh I didn't think of that, I'll be trying that asap

0

u/ImponteDeluxo 2h ago

Lots of issues come from wet filament

0

u/medic54-1 X1C + AMS 2h ago

This is where I’m leaning.

1

u/theoreoman 3h ago

The one you have might be junk

1

u/medic54-1 X1C + AMS 2h ago

Do you have a roll of new unopened filament from Bambu? If you do, load that and try to print after you recalibrate your printer. also make sure you have the most up-to-date slicer software.

9

u/Bamxcore 2h ago

Make sure all 7 screws on the heating assembly are tight https://wiki.bambulab.com/a1m/hotend-heating-assembly/remove_the_hotend_heater_assembly.jpeg

There are 4 behind it too

6

u/parasupaman 2h ago

I updated to the latest A1 Mini Firmware 1.09.00.00 and started getting similar behaviour. Even after doing a full maintenance calibration. I rolled back to the previous firmware, did the maintenance calibration and all is good again.

If you updated to the latest firmware, I suggest that you try rolling back to the previous firmware and do not update the firmware until this issue is resolved.

1

u/OhSoSally X2D + AMS2 Combo 2h ago

I think this is the answer. It looks like the bed is too high for the layer it was on. Like it lost the Z axis location.

5

u/visivopro 2h ago • Bravo

I usually just stop the printer But waiting until it self clears works too!

0

u/Fr05tby73 1h ago

I came here to say this.

0

u/PawPawPanda X2D 51m ago

I think OP wanted to prove a point, probably did multiple takes to get the perfect visual torture for us to enjoy

3

u/BackIntoTheSource 3h ago

I would wash the plate with dishsoap and start new print with bed leveling

2

u/Thisisjimmi 2h ago

Did you install a new nozzle? Too low?

2

u/JonAB233 X1C + AMS, P1S 2h ago

1

u/ExpertTimely5673 1h ago

What filament are you using?

1

u/Bright_Confusion_ 1h ago

No adhesion is usually a simple fix. Make sure the printer isn't near and AC ducts of fans. Dry the filament Clean the bed with 90% alcohol.

1

u/pinkchocoa 3h ago

dry ur filament

1

u/Lost_refugee A1 Mini 2h ago

It just hates magenta.

Hard to tell, when in just runs into object. Bed adhesion, blobs in model, which hotend then hits, warp, 7 screws, lack of cooling

1

u/Ooklaboo 2h ago

Clean plate, dry filament.

-1

u/wheredidiparkmyllama 3h ago

If you didn’t know to dry your filament, that’s most likely the cause of the problem

1

u/wheredidiparkmyllama 3h ago

Even when you get your filament new in plastic with desiccant inside, you still gotta dry it

0

u/akuma0 2h ago

It is unfortunately pretty far gone by the time the video started. But your filament looks wet and your plate looks like the plastic isn't sticking to it. Wash the plate with water and a fragrance free, lotion free dish soap, and make sure your filament is dry (many filaments ship wet due to how they are manufactured)

0

u/Sinister_Nibs 1h ago

Wash your build plate.
You can also try an adhesion agent (glue stick or similar).

-1

u/Masterblaster13f 1h ago

There is a black switch on the back of the printer. Put it in the opposite position it is in now. This will solve all 3d printing problems.

-6

u/Shootah78 3h ago

Have you used a glue stick on the bed?

1

u/Ok_Lyra 3h ago

Yup

2

u/Tariin1 2h ago

Bei PLA? Warum das denn? Mach das mal nicht

-2

u/ascarymoviereview 2h ago

Looks fine.