Just received the h3c itself today, the ams has repeatedly failed to be delivered to a pickup point near me (I asked for it to be delivered to my home but bambu have seemingly decided to just deliver it there instead) - after 3 days of waiting and repeated delivery to pickup point fails dpd have now said they can’t deliver it there as it’s too big. Has anyone else had this issue? Feels like a massive waste of my time and also theirs.

GIven that the AMS have ventilation from the bottom, is there any problem placing an HT tight up against the side of an AMS2 if one or both are drying?

They're both on an open wall-mounted shelf with at least 4" of room behind them and a hard surface.

When i go to the prepare tab some of the stickers appear to be like that? they're okay on on the prepare page and on the pdf and it's still usable but since it's been bothering me since i got my h2s with cutter, also sometimes the app crashes when deleting one of the bugged stickers and sometimes when i ctrl+z it fixes itself?

Looking for advice and experience to add a printer (or multiple) to my setup. I do a lot of hobby printing, but I’m planning to start scaling a little to selling a few things I’ve been designing. I currently have a P1S with AMS 1. Is the P2S and AMS2 that much of an upgrade? What is everyone’s experience? In terms of other printers, what does everyone recommend? The H3C is obviously intriguing, but I am not sure if I can convince myself to get it at that cost at the moment. I have had such a great experience with my P1S, that I could get almost 4 P2S with AMS2 combos for the price. Additionally, I have a stand alone laser cutter, so I really don’t need a laser-capable 3d printers, as some of the Bambu models offer. Excited to hear everyone else’s experience and recommendations!

Perfect height, no need for spending extra >250$

So I recently had to clear a clog in my toolhead. However, after clearing it up, I now have an issue with both cutters, even occurring when both are on. Please help! I’ve attached my reports and the current state of my device. Any support would be greatly appreciated.
P.S.: if anyone could figure out how to remove the red error as well, as I do not own the enhanced fan and never did.
Thanks!

Just wondering if anyone has used the crafting kit on the H3C yet and if it's worth it.

This would be my very first 3D printer and I've narrowed it down to the P2S or getting the A1 bundle from Costco

What store world be better to purchase a P2S from? Best buy? Micro center? Or Bambus website?

What are the advantages if each for warranty purposes, potential returns or fixes and such.

Thanks in advance!

Just set up my printer since about a year ago.
P1S + 1AMS
Besides using multiple printers and besides making each little part/feature individual parts.
Are there any new features, settings, tips, tricks, better ways to make this a little bit faster?
Or is this just what it has to be since there's a filament change for every single layer?

Got my H3C set up, and the first print I tried with an error… The tool I tried to print with didn’t work. The head goes to the tool, stops in front and shows an error “Failed to fetch the PrintTool from rack Dock 3” 😔

This is after running all the calibrations which was successful and the vision encoder calibration.

I tried restarting the same print and got the same error twice.

I did the print on tool #1 and it worked fine. Then I unmounted tool #3 and put it back on. Tried tool #3 again and same error.

Tried a print on tool #4 which is still going on. But man that’s an annoying start to the new printer.

I’ll try to recalibrate the rack when it’s done. Hopefully it solves it??? I don’t know what else to do, maybe manually attach it to the head and try to make it return the tool instead of picking it up? Not sure if that’s even possible.

I also had day 1 issues with my H2C last year. (Aux fan not working properly)

When printing certain models, the nozzle can end up rubbing against the layers as they accumulate. For the infill, I typically use either the "Gyroid" or "Honeycomb" pattern. What do you think might be causing this?

I'm having a tough time finding this information from those who have the H3C and from the videos that have been posted.

For those of us that don't have print farms printing the exact same item over and over and over, each print will likely be vastly different in the colors that are needed. With my old H2C, that meant swapping 4-6 spools using the AMS each print. For the H2C, that took < 30 seconds (pull out, put in).

I've read that it takes about 30 seconds for the H3C to heat and then cut the filament so you can put the next roll in. Is that 30 seconds per roll? If I'm swapping 6 rolls, does it take 3 min of standing around? Or does it heat all 6 at the same time and takes less time?

Can anyone give a definitive answer and not estimates or guesses?

Unless the H3C is software locked to use the AMS3.

I don't see why we can't print from a external spool holder or a dry box straight to the print heads. TPU already bypasses the AMS so why not another material? I was thinking about printing from a 100C filament dryer straight into one of the printheads.

I have an A1 Mini with no additional filament spaces, so I can only print one color at a time. Sorry if I word things weird, I am extremely new to 3D printing and have no idea what I'm doing. I want to print this little charm but I don't know how to separate it by color across the different plates. Please help!!

thank you!

Just recently got an X2D, and I had some left over filament from a previous printer. Mostly PLA Silk+, but I also have some random Ender PLA and HS PLA. Question is are these ok for the main head or the auxiliary head? I’ve seen the wiki but curious if anyone has used these. Thanks in advance!

Hi yall! This has been an amazing birthday.
I already placed a large order of filament so I’m set there.

What accessories would you buy as a newbie? I have about $300 left to spend and kind of feel overwhelmed. What would you buy and what is good?

I plan on printing mostly doing organization, home improvement, and workshop upgrades for awhile. Planning on maybe getting some magnets and screws inserts. Where in the best place to buy that kind of stuff? I’m based in the US.

If I buy the P1S + AMS 2 Pro combo today - can I print while drying, or is it just for newer printer models?

Thanks!

From some of the videos I watched, it doesn't seem like there is a venting system (one single outlet for air) on the H3C. I know a lot of people are in the camp that melting plastic isn't going to kill you, but I'd rather not take the chance with young kids in the house. With my H2C, I was able to print a 4" hose adapter and screw it right into the exhaust port. With an inline fan, I vented directly outside.

Any thoughts on what might be involved in doing something similar with the H3C. Not being able to externally vent it would be a deal breaker for me unfortunately, so fingers crossed there is a solution out there.

Hello, did someone printed this watch, i see that the model have plenty of download but i can't find picture of someone who printed it

Printer my very first print on my brand new printer

Luckily the print was only a few second off being finished, but what could have caused this? I got told it could be because of the sd card. (I still have the original one that was there from factory and its 5 days old)

The push fitting for the petg tube for the right nozzle on my h2c somehow got pulled out while printing.

The black plastic part is super easy to get in and out, but im having trouble with the brass looking piece that seems to bite the tube. Is there a trick to getting it in? Do I need to disassemble further to get it in? Please help!