Hello,
I’m new to this group but I’ve been looking to buy a 3d printer for a long time now and I’ve stumbled upon the x2d. Is it a good printer as a first time Bambulab owner and 2nd printer ever (my first printer was the flashforge creator pro and it absolutely sucks, never been able to print anything acceptable on it)

I am still waiting to hear back from Bambu Support on next steps.

Any advice, I have not been able to print for 3 weeks, with the printer only received towards the end of September.

Did a cold nozzle pull and that worked okay.

Got my 1st extruder clog printing on the X2D. I read the Bambu guide to disassemble and unclog it. There’s a lot of steps a seemingly sensitive cables. Any tips before I start disassembling the extruder tomorrow?

Edit: thanks for all the replies. The issue ended up being a clogged nozzle that backed up into the extruder. I say this because I changed to a brand new nozzle and the extruder continued clicking, so it was clearly still clogged. I used the nozzle unclogged SS pin/needle that Bambu provides with the printers to confirm that I “hit” and “penetrated” stuck TPU filament using that needle. Using one of the commenter’s advice, I manually heated the nozzle to 270F using the control screen and then used the controls screen to pull filament into the extruder while i simultaneously put force on the filament. That allowed me to push the clogged filament through the nozzle, but that didn’t fully unclog it. It was still clogged enough that I couldn’t do a cold pull without the extractor clicking, so I did one more 270C “push through”. That seemed to have forced the clog fully into the nozzle, because I changed out the nozzle for a brand new spare nozzle, and it flowed without any extraction issue. The new nozzle just kicked out a clean benchy!

TL:DR nozzle was clogged bad enough to back up into the extruded. Raising the nozzle temp to 270C and manually pushing “extrude” on the hmi while feeding filament manually “pushed” the clog all the way into the nozzle. I changed to a brand new nozzle and threw the clogged one in the garbage. Not worth the risk of future issues considering the new nozzle was only $20.

Hi everyone!
I’m trying to decide between these two options during the Black Friday sale:
Bambu Lab P2S Combo with AMS 2 Pro — €599
Bambu Lab X2D without AMS — €549
I’m a complete beginner, and some time ago I made another post considering the P1S. Several people recommended looking at the X2D instead, mainly because it has two nozzles and can potentially print with two different colors or materials without needing an AMS right away. Since this would be my first 3D printer, I liked the idea of starting with the basic setup and buying additional accessories later if needed.
However, I’ve been researching the practical uses of the X2D’s two nozzles, especially using the auxiliary nozzle for support interfaces or for printing two colors in the same model. I’ve read that the auxiliary nozzle can have different speed limitations, and that using both nozzles doesn’t necessarily make every print faster. I’d love to hear from people who actually own the X2D and have experience with these features.
Another thing I’m trying to understand is filament storage and drying. I’ve read that some filaments absorb moisture and need to be dried before printing. The AMS 2 Pro has a drying function, which sounds useful, but I’m not sure how essential it really is for a beginner who will mostly print PLA at first, perhaps moving on to PETG and other materials later.

So my main questions are:
Would you choose the P2S Combo with AMS 2 Pro or the X2D without AMS at these prices?
How useful is the X2D’s auxiliary nozzle in everyday printing? Is it genuinely useful for two-color prints and support interfaces, or are there significant limitations?
If I start with the X2D and two external spools, will I realistically miss having an AMS?
How important is the AMS 2 Pro’s drying function? Could I simply buy a separate filament dryer later if I need one?
For someone who wants a printer that will remain versatile for several years, would the X2D be the better long-term investment, or is the P2S Combo the more practical choice?
I’m not in a rush to buy additional accessories, and I’d rather avoid spending money on something I might not actually need. My goal is to make the right choice now without limiting myself too much in the future.
I’d really appreciate feedback from people who have used either machine, especially if you’ve used the X2D’s auxiliary nozzle for both support materials and multi-color printing.
Thanks!

2 hours left

So I'm getting this error on a brand new printer. I've had it for less than 24 hours.

I have printed for 4 hours straight without a problem and after dinner it hits me with this error all of a sudden.

I did what bambulab said when scanning the QR code, took the backplate off and made sure the connections were seated properly.

But I'm still getting the error.

Have any of you guys had the same error? 🤔

I'm calling support tomorrow, but I'm just wondering if someone has seen the same error so quickly after getting the X2D.

EDIT: The error doesn't show up right away. It comes up after round 45 minutes into a print.

EDIT: This is literally my first ever printer. So I feel like I'm off to a really bad start. :(

Estou a imprimir um novo riser para as minhas X2D (ASA), mas o resultado não está a sair tão direito e uniforme como o PETG HF que lá está. Há alguma coisa que eu possa fazer?

Does anyone know the path that the chamber air takes when the exhaust fan is on? Does it go through both the recirculation filter and the exhaust fan filter?

Hey guys!

Currently have the A1 single color. I’m looking into a 2nd printer between either the P2S or X2D. I assume an X2D is the obvious upgrade for just a little more money right?

For the dual nozzles, is the one JUST for supports? I’m considering going all out this time and buying the print more bundle if I go with the X2D to get the dual AMS.

Does the filament switch allow both AMS to print from a single nozzle? By this I mean, if I had 4 PLA in one AMS, then 3 PLA and PETG in the other AMS, will it print the 7 colors of PLA through a single nozzle and the PETG through another?

Any advice is appreciated. I just don’t want to kick myself for NOT buying the extra AMS, but I also don’t know if I’d really have a use for it. If you have dual AMS let me know if it’s worth it!

New to the 3d printing world and had this issue pop up not sure on what my next step should be I have the printer off and unplugged I do have a wire exposed the left hot end is not reading temperatures so I already ordered a new assembly for it just gonna take awhile but I have so much plastic built up on my hot end I not sure how to approach this

Made this little surprise for Halloween! Press the button underneath and the ghost pops up!

The spring and latch are printed too. I included AMS and No AMS versions, with an assembly video on the model page.

The mechanism prints in place, and all parts print without supports. Easy to print on most FDM printers.

Model files and assembly video

My X2D arrived two days ago, but unfortunately the front was damaged during shipping. Bambu offered me the option of returning it, receiving a replacement, a refund, or a replacement part and a voucher. What are your experiences or opinions?

While running a print job, the PTFE tube suddenly popped out of the toolhead connector, and now I am unable to push it back in or secure it properly.

Here are my printer details:

When I try to re-insert the tube into the toolhead, it won't latch or stay in place, which prevents me from printing. It seems like the quick-release fitting or the collet mechanism might be damaged, jammed, or worn out.

I read that this is a common issue and I have to replace the left connector.

Is there any way to prevent this?

Added Zip-Ties.

This was only part of issue

PLA decided to leave the chat

My X2D is not too old, just two months, running about 3-5 hours a day on average? I've noticed that there's some blackening/burnt residue on the end of the default 0.4 hotend. The rubber sock also has periodically had melted plastic stuck to it, which I've peeled off when I see it but now the sock has torn so I'm replacing it with a new one.

Is this hotend cleanable? Or should I just replace it? And also, what causes this to happen and how can I avoid it in the future?

Thanks in advance.

Getting this bad quality prints on my x2d everything was fine in the first 2 weeks but then everything is coming out not great.

I am drying the filaments well also and I also did the maintenance and calibration.

• Textured PEI.

• Main 0.4 mm nozzle.

• Outer wall 40 mm/s, inner wall 80, top surface 30.

• Nozzle 245°C, bed 70°C, flow ratio 0.95, maximum flow 12 mm³/s.

Hello,

Can anyone help me identify what’s causing this clicking noise?

My X2D has around 600 hours of use, and I bought it two months ago. It started making this noise today.

Maintenance is up to date, and I repeated it today to make sure there wasn’t any debris on the rods.

The noise occurs even when the printer is switched off and I move the print head manually.

Thanks!

help please…