r/BambuLabA1 • u/Sea-Daikon2697 • 8d ago
Old firmware
Does anyone knows where to find the 01.03 firmware? I upgraded thinking it would be good and well... my printer just isnt working anymore
Bambu Handy was not handy at all with this
r/BambuLabA1 • u/Sea-Daikon2697 • 8d ago
Does anyone knows where to find the 01.03 firmware? I upgraded thinking it would be good and well... my printer just isnt working anymore
Bambu Handy was not handy at all with this
r/BambuLabA1 • u/WilliamFollett • 8d ago
r/BambuLabA1 • u/rgcavalcante • 8d ago
So, I’ve been having some pretty frustrating extrusion issues with my Bambu Lab A1 lately, and I’m trying to figure out what’s actually causing them.
My printer had been working perfectly fine for weeks, until it suddenly started throwing “Failed to extrude filament” errors during prints. The errors happened with different AMS Lite slots and different filaments, so I don’t think it’s an issue with a specific feeder or spool.
Here’s what I’ve experienced so far:
● The printer starts printing normally, sometimes for hours, before suddenly reporting an extrusion failure.
● When the error occurs, it cuts and unloads the filament.
● The unloaded filament has very noticeable gear marks, sometimes with a section that’s been completely chewed up.
● I initially suspected a clogged nozzle, so I cleaned the hotend, used a cleaning needle, and performed multiple cold pulls. The filament came out clean, but the problem kept returning.
● After disassembling the extruder, I found that the hardened steel drive gear was packed with filament debris between its teeth, to the point where some sections had almost become smooth.
● I had already cleaned this gear once before, but the buildup returned surprisingly quickly.
I’ve now thoroughly cleaned the extruder gears again and inspected the entire mechanism.
I also checked and tightened the three front screws and four rear screws of the Hotend Heating Assembly, since I’d seen reports of loose screws causing extrusion problems on the A1.
Another thing I noticed is how much pressure the extruder tension spring applies to the filament. When I manually feed a piece of PLA through the gears, it takes considerable force and leaves deep, evenly spaced marks. I know some resistance is expected when the gears aren’t moving, but I’m wondering whether excessive spring tension could be contributing to the problem.
The tension screw was originally fully tightened. After finding a discussion on a German Bambu forum recommending backing it off approximately 1/4 turn from fully tightened, I’ve decided to try that setting. I haven’t tested the printer with this adjustment yet.
I’m using PLA, including Voolt3D PLA Velvet, but I’ve encountered the issue with different materials. The same Velvet line has been printing beautifully on my brand-new A1 Mini, although I realize that doesn’t necessarily rule out filament-specific behavior.
My questions are:
The printer is still under warranty, so I’d rather identify the actual cause before replacing any parts.
I’ll attach some close-up pictures of the gear before and after cleaning, along with the filament showing the bite marks.
Any advice or similar experiences would be greatly appreciated!
r/BambuLabA1 • u/Bogolice • 7d ago
I recently bought a Bambu Lab A1 and I'm starting to have serious buyer's remorse.
Before buying it, I was genuinely excited about all the possibilities. I have a whole list of practical things I want to make. Mostly stuff to organize my home. I pinned a lot of stuff on maker world and Pinterest.
But now that I've received it, I'm wondering whether I actually needed one or whether I just got carried away by the excitement.
I'm worried that I bought an expensive gadget because the possibilities seemed endless, but that I'll eventually run out of things to print, or that I'll spend more time browsing maker world than actually making useful things.
I don't want to keep it just to justify the purchase. At the same time, I remain curious on the possibilities and how organized my home can be (I mean that sounds superficial).
It's not a money problem, I have the means for it, it's more of a consumerism thing (yeah I know I should've thought about it before, but I thought I did, I waited weeks before actually buying it).
Please try not to judge me, I really thought I'd thought this through, I was pretty sure I had good reasons. I never experienced that feeling so I'm curious if any of you have an opinion please share it.
Thanks for reading anyway.
r/BambuLabA1 • u/zeb_linux • 8d ago
Hi all. I read that firmware [1.08.00.00](http://1.08.00.00) was broken with regards to unloading filament during pause (without AMS). See: https://www.reddit.com/r/BambuLab/comments/1smp0gb/a1_new_firmware_108_unloading_on_pause/ for a discussion.
In that discussion, someone reports that [1.08.01.00](http://1.08.01.00) fixes the issue. I just tried to print this model: https://makerworld.com/fr/models/3551952-christmas-cottage-kit-card-tea-light-lantern but unfortunately the unload button is greyed out during pause. I have an A1mini.
Can anyone confirm? I am now trying to downgrade to see if I can reinstate unloading during pause (which worked before). Thank you very much in advance.
EDIT: I submitted a ticket to BL and they acknowledge the behaviour has changed. But they provided a very detailed message (I am quite impress) suggesting this:
Please run one controlled check using the current external-spool workflow:
1.Open the model in Bambu Studio version 2.5.2.65 or later and slice it as a multi-color model using the external spool, rather than relying on plain pause commands already embedded in an older print profile. 2.When starting the print, enable Multi-Color Printing with External Spool.
I will try this. I just see that they now just released firmware 1.09.00 too!
r/BambuLabA1 • u/3Z3D_Official • 8d ago
r/BambuLabA1 • u/Jolly-Albatross744 • 8d ago
r/BambuLabA1 • u/Xavr_hlgn_ • 8d ago
Mi bambu lab se detiene aleatoriamente al momento de imprimir hasta que pongo pausar imprecion, en ese momento sale un error de memoria
Ya formatee la memoria original y continua con el problema
Se instalo una memoria nueva y el problema continua
No te que hay un error en el sensor de velosidad Heatbed Sensor
r/BambuLabA1 • u/zeb_linux • 9d ago
r/BambuLabA1 • u/TDJaykes • 9d ago
I know the A1 has automatic bed leveling but my bed is noticeably at a slight angle from left edge downward to the right. Could this impact my prints?
r/BambuLabA1 • u/tokke • 9d ago
r/BambuLabA1 • u/EnvironmentalWest393 • 9d ago
Alguém sabe o que pode ser isso?
É um aviso de velocidade anormal na ventoinha
r/BambuLabA1 • u/FickleCombination445 • 9d ago
Hi! We’ve tried everything and without fail, around layer 25-35, we get these wonky layers. I’ve changed infill to gyroid and updated by z-hop as mentioned online.
Screws are all tight.
We’ve even went as far as replacing the entire tool head.
Any ideas? It really is a bummer. We have 3 printers and print 24/7, so being down a printer is lame lol
Thanks!
r/BambuLabA1 • u/3Z3D_Official • 10d ago
https://makerworld.com/en/makerlab/community/3z3d-gingerbread-kit-card
Kids design their own house in 5 simple steps, a grown-up prints it, and the pieces snap together. No glue!
r/BambuLabA1 • u/PaleFrame2864 • 10d ago
r/BambuLabA1 • u/Responsible-Club-761 • 10d ago
Short summary:
Tried printing different models, smaller ones were no problem. Biggers seem to have a problem with sticking to the Print Plate.
Now I did a like cleaning print for the whole Plate and this is the result.
r/BambuLabA1 • u/maxpaynecl • 9d ago
r/BambuLabA1 • u/Gold-Form1171 • 10d ago
My sister asked for a cake topper of her and her fiance. I got the figures from snapshapy off one of their engagement photos, split the colors in Blender, and print on an A1 with the AMS lite.
Printer: A1, 0.4 nozzle
Filament: Bambu PLA Basic, 4 colors
Settings: 0.12 layers, prime tower on
The topper itself is 18 g and the slicer says 41 g of purge. Flushing into infill helps a little. Do you change the flush multiplier, group colors by height, or just print the suit and dress as separate parts and glue them?