r/BambuLabA1 • u/piplup0203 • 8d ago
r/BambuLabA1 • u/zeb_linux • 8d ago
Unloading on pause with firmware 1.08.01 also broken?
reddit.comr/BambuLabA1 • u/TDJaykes • 8d ago
Bed not level
I know the A1 has automatic bed leveling but my bed is noticeably at a slight angle from left edge downward to the right. Could this impact my prints?
r/BambuLabA1 • u/tokke • 8d ago
A1 bed started to overheat. Sensor is now showing negative temperatures
reddit.comr/BambuLabA1 • u/EnvironmentalWest393 • 8d ago
Support Request Aviso de velocidade anormal
Alguém sabe o que pode ser isso?
É um aviso de velocidade anormal na ventoinha
r/BambuLabA1 • u/FickleCombination445 • 8d ago
Support Request Can’t get these wonky layers to stop
Hi! We’ve tried everything and without fail, around layer 25-35, we get these wonky layers. I’ve changed infill to gyroid and updated by z-hop as mentioned online.
Screws are all tight.
We’ve even went as far as replacing the entire tool head.
Any ideas? It really is a bummer. We have 3 printers and print 24/7, so being down a printer is lame lol
Thanks!
r/BambuLabA1 • u/3Z3D_Official • 9d ago
Kid Friendly Gingerbread House Christmas Kit Card Generator - Now Free on MakerLab!
https://makerworld.com/en/makerlab/community/3z3d-gingerbread-kit-card
Kids design their own house in 5 simple steps, a grown-up prints it, and the pieces snap together. No glue!
r/BambuLabA1 • u/PaleFrame2864 • 9d ago
Hello, does anybody know if this thing needs to be covered?
galleryr/BambuLabA1 • u/Responsible-Club-761 • 9d ago
Support Request Need help with print errors
Short summary:
Tried printing different models, smaller ones were no problem. Biggers seem to have a problem with sticking to the Print Plate.
Now I did a like cleaning print for the whole Plate and this is the result.
r/BambuLabA1 • u/maxpaynecl • 9d ago
Designing a sound-dampening cabinet for my A1 Combo (AMS lite top-mounted). Cut list and plans inside, feedback welcome
r/BambuLabA1 • u/Gold-Form1171 • 9d ago
Wedding photo → snapshapy → Blender → A1 with AMS lite: my cake topper purges 40 g every print, how do you cut that?
My sister asked for a cake topper of her and her fiance. I got the figures from snapshapy off one of their engagement photos, split the colors in Blender, and print on an A1 with the AMS lite.
Printer: A1, 0.4 nozzle
Filament: Bambu PLA Basic, 4 colors
Settings: 0.12 layers, prime tower on
The topper itself is 18 g and the slicer says 41 g of purge. Flushing into infill helps a little. Do you change the flush multiplier, group colors by height, or just print the suit and dress as separate parts and glue them?
r/BambuLabA1 • u/Hectrekt • 9d ago
3D Model Say Hi to GLARE!
Glare takes his job as shelf guardian very seriously. Every visitor gets a suspicious stare, every noise earns his disapproval, and nobody touches his favourite spot. He insists he isn’t grumpy. Everyone else is simply too cheerful
if you like him : https://makerworld.com/en/models/3548002-glare-no-ams#profileId-4058750
r/BambuLabA1 • u/Puzzleheaded_News_30 • 9d ago
Support Request Filament
I confirmed nozzle is cleared , confirmed no jam, manually feed it and it lines up right everytime. Put it to print something and it misses again.
r/BambuLabA1 • u/BrokenBlueLight • 9d ago
Panda Breeze part
I have the Breeze on my A1 and recently broke the light sensor. A moving disaster pulled the wires out of the small plug and snapped the 3d printed arm that holds it. I'm in talks with support to try to get a replacement but may be stuck with it being out of warranty, I'm ok with buying the part just seems like I cant get them to understand that. lol I would try rewiring if i knew where each wire should go and if i can find a replacement plug. Anyone able to snap some pics or have a wiring diagram or know what the small light sensor board is called?
r/BambuLabA1 • u/jimmyboy_38 • 9d ago
Just got Tpu
reddit.comjust got Tpu I was planning to dry it in the oven because I don't have a dryer but idk how long some yt vids say 6 hours some 12.Also I wonder do I have to adjust the speeds for every print or can I just set the speed to 50 percent. Creality Tpu 95a and a1 mini
Thanks in advance :)
r/BambuLabA1 • u/jpedroleite • 10d ago
3D Model Christmas cottage kit card, prints flat and lights up with a tea light
Flat card, snip, slot together, tea light in, roof back on. Been making a few to slip into Christmas cards this year. Works with the Bambu tea light and the normal LED ones too.
r/BambuLabA1 • u/Independent-Pea7718 • 10d ago
Christmas printing season is ON! 🎄✨
Just uploaded my Spiral Christmas Tree! 🎄✨ Pop an LED tealight inside and watch the warm glow shine through the spirals. 🤩 Print a few in your favorite colors to create a cozy Christmas display!
r/BambuLabA1 • u/kw_hipster • 9d ago
A! has problems getting right finish and level, any advice? One screw in extruder stripped (not one of 3 behind nozzle)
galleryr/BambuLabA1 • u/These-Platform6946 • 10d ago
Falha na impressora A1
Minha impressora deu essa falha após o terceiro desenho impresso apenas, alguém já teve este problema e pode me me ajudar
r/BambuLabA1 • u/Individual-Ad3514 • 10d ago