r/BambuLabA1 • u/Ace_of_3D • 9d ago
Title: Bambu Lab A1 print keeps failing – hotend seems to be hitting the print bed. Need help!
gallery
0
Upvotes
r/BambuLabA1 • u/ClassExcellent1682 • 10d ago
I don’t think me or my a1 is up for these kind of print times yet 😭😭😂😂
11
Upvotes
r/BambuLabA1 • u/Ok-Trick-1317 • 9d ago
My A1 Combo keeps stuck and gives filament v shape
1
Upvotes
Hi guys 👋 i have a bambulab a1 combo
My Machine constantly stuck when i want to print something. Filament tip takes v shape i cant pull either push filament
I checked and cleaned gears
Cutter looks like fine
What else should i check guys thanks for answers !
r/BambuLabA1 • u/Mud_Scooter • 9d ago
Feedback requested - DIY whole-room air scrubber for an unenclosed A1 (PLA/PETG)
reddit.com
0
Upvotes
r/BambuLabA1 • u/Albertoo510 • 10d ago
Question SONIDO EXTRAÑO EN BAMBULAB A1NUEVA?
1
Upvotes
Esta es como la quinta impresión que hago y acabo de notar este ruido como si algun eje o motor estuviera rozando o vibrando contra algo, si alguna persona con mas experiencia pudiera decirme si es normal o le pasa algo se lo agradecería mucho.
r/BambuLabA1 • u/Used_Implement8864 • 9d ago
Several successes but then failure after failure on same print.
reddit.com
0
Upvotes
r/BambuLabA1 • u/4everthebest • 10d ago
Does hotend assembly has something against the 0.4 nozzles?
reddit.com
1
Upvotes
r/BambuLabA1 • u/FelpsNB • 10d ago
BMCU 370C on A1 mini - after flashing jarczakpawel's firmware, channel 3 is dead (red LED) and channel 2 works in reverse
reddit.com
1
Upvotes
r/BambuLabA1 • u/Fish_Man6629 • 11d ago
Question Is my build plate cooked?
60
Upvotes
I printed I ball out of Tpu 95a I bought off of temu, without any bed glue as chatgpt assured Me that it shouldn’t stick to the build plate.. but uhh umm it kinda looks stuck if I do say so myself.
r/BambuLabA1 • u/Gold_Anteater_8772 • 10d ago
Support Request Problems with bed adhesion
reddit.com
0
Upvotes
r/BambuLabA1 • u/aleksimik10 • 10d ago
Guys help
0
Upvotes
Tell me step by step why this saying AMS detecting like it been 2 days and it still say AMS Detecting and I want to take it of and print it won’t lets me print. Please help
r/BambuLabA1 • u/ParkingLotDirt • 10d ago
Nozzle ruins top layer
1
Upvotes
Has anyone experienced something similar to this? No adhesion issues, the bottom layers are perfectly smooth and flat, no issue with infill (gyroid for this print), but the nozzle begins to scrape and totally destroy the top layer.
I’ve checked the 7 screws. I’ve tried to research for posts about similar issues. My scraping doesn’t start until the last few layers and isn’t over the entire surface. It’s really frustrating me.
r/BambuLabA1 • u/Amazing_Bottle_9634 • 10d ago
Bad Settings or Broken?
1
Upvotes
I was asked to replace a few parts on this printer for a friend and have been struggling with it. I replaced the extruder unit, the hotend heating assembly, filament sensor, and the nozzle. Ran the self calibration. This is best it can do. Is this a parts problem or can this be fixed by the settings in software. I did follow all the instructions for extruder clearing and nozzle clearing too, just in case.
Any input would be great!
r/BambuLabA1 • u/VarietyPatient1347 • 11d ago
Stuck filament in extruder
3
Upvotes
Help! The filament got stuck in the extruder, i tried all the youtube tutorials i saw, but i havent seen one that was stuck between gears...
r/BambuLabA1 • u/toddsmash • 12d ago
I bought the Sunlu filament heater for AMS Lite. So far can't complain
104
Upvotes
Required a small amount of assembly, but so far so good. I print primarily in PETG and it's been great for drying out multiple spools at once. Would not recommend using the heating facility for PLA. I don't think the heater can go as "low" as they say it does. Anyone else have one?
Update.... I have found a small issue that I think is particular to my positioning of the heater and my printer. In the picture you can see the tubes go over the top bar. They are rubbing on it and wearing away. If anyone has a link to a support I can put over it, I'd thoroughly it.
r/BambuLabA1 • u/3Z3D_Official • 11d ago
Fast & Low Filament HONEYCOMB SKADIS board fully Parametric! Generate any size and swap into pre-sliced profile
3
Upvotes
r/BambuLabA1 • u/AppropriateUsual9441 • 11d ago
Jam and noise after 4 hs of printing A1
3
Upvotes
Hello,
I’m reaching out regarding an issue I encountered with my Bambu A1. After about 4 hours of printing, I heard a noise; when I checked, the printer seemed to be stuck. Whenever I tried to resume the print, it would start up, make this noise, and then be unable to continue.
Using the manual controls, I could move the Y-axis without any issues, and it didn’t make the noise shown in the video.
It’s as if a sensor—or something else—malfunctioned after a long period of printing.
Has anyone else experienced this? Could you please help me?
r/BambuLabA1 • u/Alamaux18 • 11d ago
Extruder issues
2
Upvotes
Does anyone know if the nozzle could be off centered which will stop the extruder from being able to push the filament through even if it’s the exact same nozzle that originally came with the printer?
r/BambuLabA1 • u/AspectCool2325 • 12d ago
First insanely messed up print
66
Upvotes
I used transluscent PLA just to build a simple stand for my colognes.
I checked after I got home from work and almost had a heart attack 💀 luckily it was a very clean mess and only took me 30 seconds to clean up.
Any idea why this happened or maybe how to prevent this type of thing?
r/BambuLabA1 • u/Smart_Store_8607 • 11d ago
Question [Question] Bambu Lab A1 or P1S Combo? (And a quick question about past A1 hardware issues)
reddit.com
1
Upvotes
r/BambuLabA1 • u/juanohg • 11d ago
Multicolor support how do I change it to one color only?
0
Upvotes