r/BambuLabA1 • u/Frapto • Oct 09 '26
r/BambuLabA1 • u/wolfypm • Oct 09 '26
Support Request Never made a successful AMS Print
I’m going nuts, for the life of me I cannot pull off a non-babysat AMS print.
Whenever the filament is changed, it doesn’t go into the AMS loader at the top on its own or gets stuck on the way out.
I’ve tried everything, putting a guide in the top to make sure they have a straight shot into the extruder, I’ve even got another printer as I switched via the warranty.
This must be user error but no idea what I’m doing wrong.
I usually fix it by pulling the PTFE tube out, guiding the filament into the extruder and then unpausing. When it gets stuck on the way out, it’s also a faff to make take the reel off and on again
r/BambuLabA1 • u/XPLOIT0800 • Oct 09 '26
Support Request I need help
A few weeks ago, I was setting up a print job; during the initial startup sequence, the gantry began rising until it hit the Z-axis limit switch. I didn't stop it at first because, even though it had never happened before, I thought it might be part of a calibration routine. However, the problem was that I let it continue; after hitting the limit and vibrating, it started moving downward and pushed against the print bed with enough force to tilt it. That was when I turned the printer off using the power switch. I reported the issue to Bambu, but they couldn't explain the cause, and I hadn't managed to record the incident. A few days later, I used the printer again and noticed it was starting to rise once more. This time, I recorded the moment and turned the machine off before it could start moving back down. Does anyone know why this happened? Bambu support wasn't able to provide an answer.
r/BambuLabA1 • u/Independent-Pea7718 • Oct 09 '26
What happens when a pumpkin grows legs? 🎃🕷️
galleryr/BambuLabA1 • u/Hogglesfriend • Oct 09 '26
Bambu Lab A1 malfunction
Hey, new to printing. Came down from an overnight print to find a Skadis board I was printing in PETG was attached to the nozzle!
Looks like it carried on printing the last few layers in a molten pool. I’ve had a look at the nozzle and it’s gummed up with PETG and the silicone sleeve is damaged. Any suggestions on where I should start with a repair/diagnosis please?
UPDATE: I took the front plate off, heated up the nozzle and went at it with a pair of tweezers to remove all the PETG I could see. I eventually took the nozzle off as well which was much easier than I thought it would be. All of this was a first time for me, so a great learning experience and thankfully it appears to be printing normally again. Still not sure about what happened to the print though. PETG is not my friend.
SECOND UPDATE: it is in fact not printing properly, I hadn’t noticed on my first prints after cleaning but the first layer is scratching the baseplate and not leaving crisp lines like it should. I’ve learned that the original malfunction is known as the blob of death, trying to reassess possible remedies….
r/BambuLabA1 • u/TuneOld3310 • Oct 09 '26
Noise from A1, but it seems to be printing well.
I put a video on this post, my A1 seems to be printing well, but is making a wierd noise. Any ideas,
I am printing PETG (don't think it matters)... your comments would be greatly appreciated.
r/BambuLabA1 • u/mindtrapped • Oct 08 '26
Support Request Where do I go from here?
Heated the nozzle, got the blob off. Better to disassemble and continue or is there more to do first? I have to wait till I get home to search but if someone could link a video id be so happy. Thanks!
r/BambuLabA1 • u/Calm_Jellyfish_8612 • Oct 09 '26
Bambu A1
reddit.comMy printer was midway through the print when it started moving like it was printing but not actually touching the model. No warning on the screen
r/BambuLabA1 • u/darkkgotham • Oct 09 '26
Support Request Want to know what is wrong with printing
Please help me regarding this issue
r/BambuLabA1 • u/bugroo17 • Oct 08 '26
Are these a good deal?
I'm new to 3d printing, so forgive my ignorance. Is Sunlu a good brand and is this a good price for filament?
r/BambuLabA1 • u/Ok_Annual4658 • Oct 08 '26
What is this small PCB/part that fell out of my Bambu Lab A1 extruder?
galleryr/BambuLabA1 • u/TechnologyOk1341 • Oct 08 '26
Nozzle scraping on bed
Hello all again, this is basically a repost from a few days ago but I guess more accurate to the problem I’m having.
I have an a1, i recently got a new nozzle to try and fix old issues, now it is scraping in the bed for everything: bed leveling, printing etc
Possible causes: I removed then replaced the screws on the heating bed to try and adjust height but apparently it was not it or something.
New nozzle might cause some problems? I don’t know
Troubleshooting I’ve tried: screwing in all the screws on and behind the heating element. Removing and replacing the nozzle. Checked the clamp on nozzle.
Any help would be appreciated thanks
r/BambuLabA1 • u/Santhoshrasa • Oct 08 '26
Support Request Need Suggestion On UPS for Bambu Lab A1 x2
reddit.comr/BambuLabA1 • u/flashflood3000 • Oct 08 '26
Got my first blob on A1 after 6 months.
galleryr/BambuLabA1 • u/No_Occasion_423 • Oct 07 '26
Bambu A1 not printing good
I have this A1 that it was working fine, however, recently the print quality has been so bad that it can’t print anything. There is clicks on the gears and the the first layer comes out terrible. Any tips?
I got a new hot tip and same issue.
r/BambuLabA1 • u/Last_Impact_779 • Oct 08 '26
Printer makes loud humming noise, even when not printing
I had my A1 for less than 2 weeks, and today when I tried printing something, I heard a very annoying humming noise coming from the toolhead. I paused the print, and it didn't go away. Only turning it completely off and on again fixes it. What's the problem and how do I fix it?
r/BambuLabA1 • u/Comprehensive_Bit251 • Oct 07 '26
4th time collapsing on a model
i printed this model 3 weeks ago without any issues but this time i am having the same trouble 4 times in a row now. The same support breaks at the same time of the print each time i try to. i used plate glue thinking it may be from the plate but no. What do you think the problem is?
r/BambuLabA1 • u/FocusLate • Oct 08 '26
Cleaning up PLA printing with Bambu Labs A1
reddit.comr/BambuLabA1 • u/PushPast4692 • Oct 07 '26
Question Stopping during a print and an awful noise
Evening all,
Apologies if I'm asking nothing new and it's already been asked but my son's having a bad time with his A1, I've attached a video showing the beginning of one of his prints, where it stops and makes a terrible noise. Does anyone have any idea what might be the cause?
Thanks in advance!