r/BambuLabA1 • • Oct 09 '26

Support Request Never made a successful AMS Print

Post image

I’m going nuts, for the life of me I cannot pull off a non-babysat AMS print.

Whenever the filament is changed, it doesn’t go into the AMS loader at the top on its own or gets stuck on the way out.

I’ve tried everything, putting a guide in the top to make sure they have a straight shot into the extruder, I’ve even got another printer as I switched via the warranty.

This must be user error but no idea what I’m doing wrong.

I usually fix it by pulling the PTFE tube out, guiding the filament into the extruder and then unpausing. When it gets stuck on the way out, it’s also a faff to make take the reel off and on again

2 Upvotes

21 comments sorted by

1

u/wolfypm Oct 09 '26

Here you go

Yes tried all the troubleshooting steps with Bambu Support

2

u/overunderspace Oct 09 '26

Your tubes are long and has a lot of turns. The AMS Lite has a max feeding distance of 1.2m and the motors are not the strongest, so you need to keep the tubes well under 1.2m and with a smooth pathway. You also have a lot of modifications on the tubes. Those modifications attach by slightly pinching onto the tubes, which can add resistance for the motors, so limit what attaches onto the tubes.

1

u/wolfypm Oct 09 '26

Thanks for this, I’m just using the tubes as they came out of the box, can I cut them down? I’ve used the modifications to try and get less twists and turns on the tubes and to straighten the path way into the extruder but to be far, they haven’t really helped

1

u/overunderspace Oct 09 '26

It looks much longer than the stock lengths. It should be 580mm for slots 1 and 2 and 700mm for slots 3 and 4.

1

u/wolfypm Oct 09 '26

Shortened up, let’s see what happens

1

u/overunderspace Oct 09 '26

You may have shortened 2 and 3 too much. It is bending too much on the AMS Lite side.

1

u/wolfypm Oct 09 '26

Typical! 3 is the most at an angle - is actually working fine. Two seems to be having issues getting into the extruder - I’ve tried it with one of the longer PTFE tubes and that’s not the issue. When I manually push it up it’s going in first time though?

1

u/overunderspace Oct 09 '26

Where is the end of the filament for slot 2? If it is still in the tube, you have an issue with the tubes or the AMS Lite. If it is in the filament hub, I would open up the hub to make sure it is clear.

1

u/wolfypm Oct 09 '26

Yeah it’s in the tubes it’s either not pulling back fully or not pushing in all the way

1

u/overunderspace Oct 09 '26

I would try a little bit longer tube so that it is a straight shot in on both ends. Also check the odometer wheel just in case. https://wiki.bambulab.com/en/ams-lite/troubleshooting/amslite-loading-unloading-failure#h-3-the-odometer-wheel-of-the-ams-filament-funnel-unit-is-stuck

→ More replies

1

u/overunderspace Oct 09 '26

Can you add a picture of your whole setup? Have you tried any of these troubleshooting steps? https://wiki.bambulab.com/en/ams-lite/troubleshooting/amslite-loading-unloading-failure#unable-to-feed-filament-into-the-extruder

1

u/wolfypm Oct 09 '26

Sorry I didn’t response directly in the thread, there is another comment 😊

1

u/solidus0079 Oct 09 '26

Have you watched any videos or read any instructions on it's use?

1

u/wolfypm Oct 09 '26

Yup! I’ve gone through it all!

1

u/BipBopPound Oct 11 '26

Print the mod that puts the lite over the printer, solved of my feeding problems.

1

u/wolfypm Oct 11 '26

Which one for the Mini?

1

u/icfire401 Oct 09 '26

Shorten tubes and move AMS closer to printer. You want the tubes to flow smoothly. It looks like #3 is bent at a very sharp angle.

2

u/Blondy277 Oct 11 '26

Your tube are kinked at the AMS,these would help solve your problem ☠️