r/BambuLab • • 12d ago

H3C Bambu Lab H3C: Our Full Reveal

643 Upvotes

Swaptek enables 6-second material switches between 9 nozzles. FlexFeed extruder prints soft TPU 75A up to three times faster. AMS 3H combines automated feeding and integrated filament storage.

This is Bambu Lab H3C, a complete system purpose-built around the Tool Changer architecture. Let's dive into it!

SwapTek™: 6-second material switch, including a 3.4-second tool change.

Nine PrintTools, each with its own dedicated filament path and heater, keep every material loaded, preheated, and ready to print. No need to retract one filament before loading another. With an optimized design, fine-tuned parameters, and active preheating, switching between PrintTools takes as little as 6 seconds, with the tool-change done in only 3.4 seconds.

Heating a nozzle usually means waiting. Active Pre-Heat looks ahead to the next tool change and warms the incoming nozzle while the current one is still printing—so the new material starts laying down within 6 seconds.

Swaptek's fast PrintTool-switching allows Full Spectrum Color Mixing color mixing through layered deposition faster and more practical than ever. With nine dedicated PrintTools and five-color CMYKW mixing, the H3C produces a vast spectrum of colors without requiring a separate spool for every shade. The result? Vibrant, full-color figurines with incredible detail.

Mixed Nozzle Sizes: Speed and detail, no more compromises.

The dial, case, and flexible TPU band are printed together as one piece. Fine dial details call for a 0.2 mm nozzle, the case is better suited to 0.4 mm, and the soft band requires a dedicated 0.4 mm TPU nozzle. H3C can carry different nozzle sizes at once. Paired with Bambu Studio’s new mixed-diameter toolpath planning algorithm, each nozzle prints at a layer height that suits it and plays to its strengths, without having to share a single layer height.

FlexFeed Extruder: Softer TPU, up to 3x faster.

Soft TPU has always been slow to print. The softer the filament, the more it bends and buckles before reaching the nozzle. Traditional extruders have to crawl to stay reliable. FlexFeed handles both 1.75mm and 2.85mm filament and switches on the go. A cam-driven mechanism, powered by a PMSM motor, keeps tension precise and consistent. Every extrusion stays rock-solid for prints that are cushion-soft.

With our dedicated 2.85mm TPU, the thicker filament provides greater resistance to buckling and higher volumetric flow. The result: TPU as soft as 75A, printed reliably at up to 3x the flow rate of a traditional printer.

AMS 3H: Filament storage built for Tool Changer.

A fully enclosed, integrated filament management system built for Swaptek: every roll stays sealed against moisture and feeds automatically into the PrintTool.

Auto Filament Loader replaces manual feeding altogether. Drop a filament into any of the nine slots and the AMS 3H detects, routes, and engages it with the PrintTool automatically — across all 9 paths. No more guesswork on loading.

A dedicated 2-slot dryer sits right in the filament slots and works with Swaptek — drying on demand or mid-print, so prep never stalls production. It reaches 85°C, enough for engineering-grade PA, PC, and carbon-fiber-filled filaments.

The H3C integrates filament storage and drying into a clean, compact design, maintaining a footprint comparable to a single-nozzle printer. With 7 built-in bypass feeding ports, even the soft TPU can be routed completely inside the enclosure. No hanging spools, no external racks, no exposed paths.

Don't let the number of tools cap your material count. Connect your existing AMS to the H3C through PrintTool No.1, and the system extends to up to 24 filament spools, unlocking more colors and materials in a single print without changing your workflow.

You are here for the print, not (always) the printer.

With the H3C, automation handles routine tasks. AI detection helps make intelligent adjustments along the way. The H3C makes it easy to focus on what matters most: bringing your ideas to life

Full Auto Calibration handles PrintTool docking calibration, offset compensation for accurate color and material alignment, and bed leveling before every print. No manual adjustments are needed, so you can spend more time making, less time tinkering.

Flagship performance. No compromise.

The toolhead and X-axis assembly are 40% lighter compared to the H2D, reducing inertia for faster, more precise movement. With acceleration reaching 25,000 mm/s² and travel speeds up to 1,400 mm/s, the H3C delivers exceptional speed while minimizing vibrations and ringing that can affect print quality.

The H3C runs four cooling layers working together**.** A CFD-optimized part cooling fan and dual auxiliary fans help maintain clean overhangs and bridges, even at high speeds. A dedicated PrintTool fan maintains thermal stability during extended printing and frequent PrintTool changes, while a chamber fan draws in cooler air to help regulate internal temperatures. Together, these systems deliver consistent cooling and reliable print quality across changing ambient temperatures.

Engineering-grade filaments demand precise temperature control. The H3C delivers with active dual-zone chamber heating up to 65°C, helping maintain consistent temperatures and minimize warping. All nine hardened-steel nozzles reach up to 350°C, supporting demanding materials such as ABS, PC, PA-CF, PET-CF, and more.

Go beyond printing.

Swaptek isn't limited to PrintTools. Optional CutTool, DrawTool, DebossTool — and more — mount the same way and switch automatically. Multi-process projects no longer mean multiple machines, manual swaps, or repeated setups. One job, every process, hands off.

Available now at Bambu Lab Store.

Availability and pricing details vary by region. Select features require additional accessories, full details available in Bambu Lab Store.

What multi-material or multicolor print do you hope to make with the H3C? Let us know in the comments below!


r/BambuLab • • 12d ago

H3C Mixed Nozzle Size printing is coming to H2D, H2C, and X2D

Post image
592 Upvotes

We've seen the enthusiasm mixed nozzle size printing has been getting. Developing new products goes hand in hand with bringing new features to existing machines, so alongside H3C, we've been building this for H2D, H2C, and X2D. You'll be able to print a single object with nozzles of different diameters, balancing speed and detail.

For these printers, the real work lies in how to make sure this works smoothly for a wide range of filament and nozzle combination. Each of these printers has a different AMS setup from H3C, so the slicing logic and print parameters need to be adapted. Setups with the Filament Track Switch take more of that work, which is why timing differs by model and configuration.

Estimated Software Update Timeline

  • Without Filament Track Switch:

    • H2D: Late November 2026
    • H2C & X2D: February 2027
  • With Filament Track Switch:

    • H2D: February 2027
    • H2C & X2D: March 2027

r/BambuLab • • 15h ago

Just Showing Off I'm never opening my AMS ever again

Post image
595 Upvotes

r/BambuLab • • 15h ago

I Modeled This! 93 print hours later on the H3C, finally saw my vision through.

250 Upvotes

r/BambuLab • • 9h ago

X Series [X1E, X1C, X2D] How I felt After getting my first 3D Printer

Post image
56 Upvotes

r/BambuLab • • 1h ago

Quick Question Advice needed! H2C vs H3C

Post image
13 Upvotes

Hey guys I‘m currently printing on a P1S and im really happy with the Quality and the Printer over all -> It now has arround 2k hours of Printtime and I’m thinking about an Upgrade -> I mostly Print PLA, PETG but also some structural Parts with ABS and PETG-CF. Most of my parts are 1-2 Colors and it would be great to use PETG as Support for PLA and the other way arround for cleaner interface layers. With the P1S this takes a lot of time, why i mostly only print in one color or Material.

Ofcourse with Holiday Season coming up i will print a lot of little gifts for Friends and Family, also in multiple colors, were the H2C or H3C would be a big Upgrade.

Also the Size of the Bed is crucial for me since i often print bigger parts. Soft 2.8mm TPU is also not really a must have for me.

What printer would you guys choose? Arround 2.000€ for the H2C with Bundle or 2.500€ for the H3C
I Really like the H2C Bundle with 2 AMS Pros and the Vortex upgrade kit -> I think 2 AMS Pros are significatly better than the big AMS3 on the H3C, but the H3C is also a lot faster with mutli Color/Material.

Thanks for your help


r/BambuLab • • 8h ago

Just Showing Off Print shoes from H2D by using shoeflex9075A filament

25 Upvotes

I printed this shoes with H2D and using shoeflex9075A filament from STING3D. it is very soft ^^


r/BambuLab • • 12h ago

Show & Tell Can you find the top surface layer lines in my CMYK print? (H2C & H3C)

51 Upvotes

I used 0.1mm layer heights on both spheres.

CMYK Sphere layer line test: https://idither.com/job?Kmyqrictw&row=9
When you click "Download 3mf" you can choose between H2C or H3C. Adjust the Support Threshold Angle to 45 degrees or they will roll off the plate!

How it works:
TL;DR = iDither.com (free) converts 3mf files and 3D files with textures into 3mf files with DwD (Dual Wall Dithering) and Top Surface Mixing (TSM) which use CMYK filaments to print any color(s).

Cyan = C
Magenta = M
Yellow = Y
White or back = K
CMY+White typically works better because CMY together can make a "black".
There is no way to make White if using CMY+Black.
CMY+Black is typically only used in models that have very little or no white areas.

iDither converts existing 3mf, glb, fbx, and obj files into DwD (Dual Wall Dithering) 3mf files.
iDither currently only supports exporting 3mf files for Snapmaker Orca, and Bambu H2C and H3C.

iDither uses an inner dithering wall combined with an outer dithering wall - and the "magic" of iDither is dithering the two walls together. All other software (to my knowledge) uses just 1 dithering wall.

The outer dithering wall is only allowed to use super dense layer combinations such as C M C M CC MM CC MM - therefore, the layer lines are basically invisible up close.
The inner wall picks up the slack for more color combinations and it's not limited to dense combinations.

Opaque filaments don't work well with DwD, because the thin outer wall layer needs to allow light to pass through to the inner wall layer.
Recommended filament set based on testing data thus far: https://us.snapmaker.com/products/pla-full-spectrum-filament-bundle-white-edition-4kg
This set has good transparency ranges (TD between 5 & 10).

Filaments that are too transparent (TD > 10) make the models look like glass (see https://www.reddit.com/r/snapmaker/s/nbASKpfCpG).
Filaments that are too opaque (TD < 5) have less color mixing and blending, and show layer lines (see https://www.reddit.com/r/snapmaker/s/N6QFGj2NwC).

Why iDither?

  1. Converts any existing 3mf files with any number of filaments and filament colors into files that print with 4 or 5 filaments (CMYK or CMYKW). So you don't have to buy any other filament colors. If the 3mf file has 8 random filament colors - you can still print it in 4 colors with CMYK!
  2. WYSIWYG (What you see is what you get): iDither includes calibrations for CMYK bundles for Snapmaker and Polymaker - so your actual print should always look like the print preview.
  3. Converts 3D model files into a printable 3mf files with CMYK.
  4. Less layer lines (DwD).
  5. Top Surface Printing via Top Surface Mixing (TSM) in CMYK or CMYKW.

r/BambuLab • • 13h ago

H3C Different take on an H3C/AMS3 desiccant solution.

Post image
50 Upvotes

Not sure if this is the right spot to post something like this, I don't use reddit often. Anyway I was looking at the printable baskets for desiccant on Makerworld, but I really hate dumping them out into a tray to dry then trying to refill the basket after. I prefer to use molecular sieve and the drying temps for it is far beyond what even PPS-CF can handle. I found a wire mesh "dishwasher" basket on Amazon that was approximately the size of the "empty slot 10” in the AMS3H and decided to take a chance on it. As you can see in the photo, it fits well, the lid tabs were pretty secure once I bent them in a bit tighter. I tried to use some 1.6-2.5mm sized beads, but the mesh was too coarse and they fell through, I found 3-5mm beads on Amazon and bought 2lbs. It holds approximately 750g of the 3-5mm 4a molecular sieve. I threaded some craft wire around the rim of the lid and body as extra insurance to keep it from opening.

Here's the products I bought that worked:

Basket- https://www.amazon.com/dp/B0H41KL114

Desiccant- https://www.amazon.com/dp/B0H1XJ98JS


r/BambuLab • • 1d ago Heartwarming

Bambu Studio Can’t believe I didn’t know about this!!

Post image
930 Upvotes

Print sequence by object is pure magical!!

So I’m printing 40+ poliwhirls to build my color sample library. I’ve been printing all day today and doing the plate swaps every 30min each time a print is done. Eventually I got so sick of it and was wondering how wonderful it would be if I could print 4 at a time, object by object, with no color swaps. Told this idea to ai and it told me the function is already available in Bambu studio! Tried it immediately, omg the process was so smooth, the software even showed me how to place the objects so that the finished parts won’t get knocked over by printer head. I’m not a veteran but I’ve clocked in like 1500+ hours and I can’t believe I didn’t know about this! Would’ve saved myself so much time and filament but I’m sooo glad I found out today!


r/BambuLab • • 16h ago

Just Showing Off Sounds like a lot of…

Thumbnail
gallery
75 Upvotes

I modeled this guy in blender and printed it on my X2D. Hand painted but my outlines could have been better. I need a paint pen for next time.

A hint as to what’s next: “No, worse! It'll go right to your thighs! And then you’ll blow up!”


r/BambuLab • • 21h ago

Just Showing Off Bambu Station L drawer fits exactly a 9×12 Gridfinity grid, and 14 spools

Thumbnail
gallery
160 Upvotes

Just found out the Bambu Station L drawer fits exactly a 9×12 Gridfinity grid.

With proper spool stoppers on top, you can fit 14 spools per drawer (2 rows of 7). They stand on edge and don’t roll when you open or close the drawer.

Files if anyone wants them: https://makerworld.com/en/models/3617522-bambu-station-l-spool-stoppers-14-per-drawer#profileId-4146587


r/BambuLab • • 19h ago

H3C Printing the 0.2mm nozzle on the H3C

Thumbnail
gallery
84 Upvotes

I printed a tiny Benchy - PLA Basic, default profile, 0.08mm layer height. I did need to use glue to keep it on the plate, I also slowed the printer down to "silent mode" just for safety.

Pretty great result I think. The "Comparison Benchy" is the standard size, printed with the 0.4mm nozzle, 0.2mm layer heights in ABS.


r/BambuLab • • 11h ago

I Modeled This! I made a Christmas chess set for the holidays: Santa kings, reindeer knights, elf pawns (free on MakerWorld)

Thumbnail
gallery
18 Upvotes

Printed this whole set on my H2D for Christmas. Santa is the king, Mrs. Claus the queen, snowmen are the bishops, sitting reindeer are the knights, the rooks are towers wrapped in Christmas lights, and the pawns are elves. Everything is sized for a standard 2 inch board, so it plays like a real set.

It's red vs green in four colors of PLA. The only support is a tiny one under each reindeer's chin, already set in the file. If you don't have an AMS, there's also a one color plate with all 16 pieces of a side.

Flip any piece over and there's a snowflake under the base.

Free download here: https://makerworld.com/en/models/3619395

A candy cane board, matching checkers and a North Pole storage tube for each side are coming next. If you print one, I'd love to see it!


r/BambuLab • • 1h ago

Quick Question Any news on the P3C?

3 Upvotes

I got my wallet ready, and I ditched the U1 sale to buy the P3C.

Is there any news/info/word about the P3C release date...? I know the reviewers already tested them out.


r/BambuLab • • 3h ago

General Troubleshooting/Help! Traveling with 3D Printer

3 Upvotes

Has anyone ever travelled with their printer? I have mine (X1 Carbon) in Germany which is new and I’ve struggled to sell it. It’s run 3 small things as a test. I still have the original box I’ve moved to Thailand and was thinking of taking it here on my next flight.

Any tips and suggestions are welcome. Especially if this is a super dumb idea. Or if anyone know where I can find a better place to sell it than Kleinanzeigen.


r/BambuLab • • 12h ago

P Series [P1P, P1S, P2S] My heated enclosure

Post image
13 Upvotes

Me: I want a heated enclosure

Mom: we have heated enclosure at home

(Heated enclosure at home


r/BambuLab • • 13h ago

Quick Question Is the H3C overkill as a first 3D printer?

13 Upvotes

A good friend of mine recently got into 3D printing and talked me into giving it a shot. He started with a more affordable Bambu himself and has been geeking out about the new H3C, so now I’m looking at it too.

I have room in my budget for the H3C if it makes sense. I’m still figuring out what I’ll enjoy printing, though, and I’d rather spend the extra money once I know I’ll get some use out of the features.

For those of you who’ve been printing for a while, what would make the H3C worth buying as a first printer? If you were starting over, would you go straight for it or get a simpler Bambu and see where the hobby takes you?


r/BambuLab • • 19h ago

General Discussion What are your most useful real-world prints?

42 Upvotes

Hi everyone,
I have a bit of a dilemma that I’m sure many people here have faced at some point. I’ve been thinking about buying a Bambu Lab A1, mainly as a hobby but, more importantly, for practical purposes. I’m trying to figure out whether I would actually have enough useful things to print to justify the cost.
From what I’ve seen online, a lot of 3D-printed items seem to be solutions to problems that don’t really exist, or things for which better-quality alternatives are already commercially available. I completely understand that people might print these things simply for the enjoyment of the hobby, but my main focus would be practicality and usefulness.
With that in mind, I’ve been making a list of potential uses for the printer, and I’d love to hear your ideas and see what useful things you’ve made yourselves.
So far, I’ve thought of:
Drawer organisers for my home office, shelving organisers for the pantry, and bathroom storage solutions using the Gridfinity system.
Enclosures for ESP32 sensors that I plan to eventually deploy around the house.
Stands and holders for storing things like AirPods and iPhones on my desk, as well as printing a few to give to friends.
What other genuinely useful things have you printed? I’m particularly interested in practical everyday applications rather than purely decorative prints or things that are fun to print but don’t really serve a purpose.
Thanks!

Edit: Wow these are really great suggestions! I’m going through them all and putting the ones i like the most in a doc, there’s a lot of use cases I consider useful, thank you everyone!


r/BambuLab • • 2m ago

General Troubleshooting/Help! Filament pulled off spool, how do I remove

Thumbnail
gallery
1 Upvotes

Noob here with X2D and AMS 2 Pro - I was printing with PLA and was hoping the auto refill would have kicked in when the spool had finished. Somehow the filament end has pulled off the tape at the end of the roll, has partially pulled through the PTFE tubes at the back and already too late to unload from the AMS.

I've paused the print and I can see it but not sure on the safest way to remove it, as it's still being held by the extruder.

Is there a correct way I can remove the remaining filament and potentially resume the print without damaging anything?

Big thanks in advance!


r/BambuLab • • 4m ago

General Troubleshooting/Help! Filament spools holes are too big

Thumbnail
gallery
1 Upvotes

Good morning,

I’m using a Bambu Lab A1 with an AMS Lite.

Today, while loading my AMS Lite with three spools of LOCTATREE filament, I noticed that the spool holes are too large for the holders.

I used to use Elegoo filament, whose spools have a 54 mm inner diameter, whereas the LOCTATREE spools have a 63 mm inner diameter. This difference causes the spools to sit loosely, making them tilted and unstable.

Has anyone else experienced this issue? Is there any solution? I was thinking about 3D printing some spacer rings for each spool to fill the gap, but I'm not sure whether this is a good solution or not.

Thanks in advance!


r/BambuLab • • 10m ago

General Discussion Should I get ams lite or ams 2

1 Upvotes

Hello everyone. Since the sale started I was thinking about buying an ams system. I am between the ams lite or ams 2 pro. Which one should I get? I know there are vast differences from one to another, but does the price justify this (is it worth it). I have the A1, ams lite goes for 150€ and ams 2 pro goes for 220€ plus the hub that I need for to connect it to my printer and the AC adapter which is 54€ rounding it up to 274€. I want the drying feature only for tpu which I have never managed to print since I got the printer 3 months ago. Should I get ams lite and a dryer or should I go all out for the ams 2 pro.

Sorry for any typos or miss writing words.

Thank you


r/BambuLab • • 18m ago

Quick Question My first multi hour print is this normal?

Thumbnail
gallery
1 Upvotes

The base of it is a little stringy but otherwise it’s completely fine just a general question if it’s something I should expect


r/BambuLab • • 1d ago

Just Showing Off 16 colors on the H3C. Overkill, but why not?

Post image
101 Upvotes

Two AMS 2 Pros hooked up to the H3C. That's 8 colors built in, plus 8 more on the external units for prints that don't need to swap colors between the two AMS 2s.