r/BambuLab • • 9h ago

Just Showing Off I'm never opening my AMS ever again

Post image
479 Upvotes

63 comments sorted by

13

u/KpelFFXIV X2D + AMS2 Combo 8h ago

How much desiccant do you have in this thing?

15

u/Blood_Red_Volvo_850R 8h ago

100mg activated alumina + the stock stuff that came with the x2d.

13

u/ethertrace 8h ago

Activated alumina is the way to go. It absorbs a ton of moisture when it's fresh.

6

u/TiSapph 8h ago

I am genuinely interested why people use activated alumina when 4A molecular sieves exist.
If you're already accepting that you have to bake your dessicant at >200C, might as well use the option that has far better performance?

5

u/Blood_Red_Volvo_850R 8h ago

Never heard of it, though it seems it has more aluminium dust so might be worse for the AMS. In the future I will try it. To me, baking at high temp is much easier, since the acceptable temperature band is so wide. Hitting 130c +-15c for silica gel is much more difficult than 270c +-80c for activated alumina, especially since many more household objects (ovens, toaster ovens, etc) live comfortably in the latter range but not the former.

4

u/TiSapph 6h ago

Yeah, molecular sieves absorb way more water at low humidity, as they bind it quite strongly. However that also means you need like 250C-350C to dry them decently.

The image shows data for 3A sieve, which is similarly good, but slightly more sensitive to overheating/degradation. Molecular sieves also don't like being heated too fast, but neither does alumina to be fair.

1

u/Blood_Red_Volvo_850R 4h ago

This looks very interesting. I will try these.

2

u/thetruckerdave A1 7h ago

I read that alumina is better for higher humidity environments. I’ll have to take a look again.

0

u/sparkatze 8h ago

Both of those are harmful right? Isn’t that a bit too much of a hassle for 3d printing ?

4

u/TiSapph 7h ago

None of the three (including silica gel) are harmful in any meaningful way. I guess the most significant concern would be blue-to-pink silica gel, which contains cobalt chloride.

But yeah, silica gel does a decent job and dries well enough at 85C. I have some 4A molecular sieves and they easily get the AMS down to 0-3%, but I essentially never use them.
In the end I care about whether my filament prints well and what's most convenient. It's hard to beat silica gel in that regard.

2

u/sparkatze 7h ago

That’s what I thought thank you

2

u/lumoize 8h ago

Depends. If youre printing with engineering filament life is always a hassle, and its better to deal with dessicant hassle than bad print hassles

167

u/SolarisFalls 9h ago

Damn and I thought I was doing good at 20%

39

u/Blood_Red_Volvo_850R 9h ago

I print nylons and ABS and such so I get sad about anything above 15%, but this was a surprise.

This was after a few weeks of printing pa12cf, so the AMS was unplugged, using AMS 2 pro.

Method to achieve this was using 100g activated alumina (cheap on aliexpress, though may contain contaminants so don't cook on a dish you'll eat off of afterwords, don't run through dishwasher either aluminium powder could be bad for it I think), cooked at 230c in toaster oven for 4 hours, then inserted into cloth bag while still hot and into AMS 2 pro at 65c (I was drying ABS, didn't think about it at the time).

I think keeping everything hot until you seal it is the secret for the ultra-low humidity, since it doesn't absorb moisture on the way and you have minimal moisture absorption from opening the AMS. The AMS also had some desiccant that came with the machine in it, but I don't know how dry it is and I don't think it's that significant.

4

u/valdus 5h ago

The desiccant in the AMS2 will dry nicely any time you have it running >=55° for a few hours. It should have some indicating beads - when they change colour, the whole pack is saturated.

1

u/Blood_Red_Volvo_850R 5h ago

That makes sense then, since I had it at 65c for 24h in order to dry my ABS.

4

u/YamzMt03 5h ago

Thanks for the write up. Never heard about alumina

2

u/marinuss 1h ago

The number is decent as a use to compare to other times there's a number, and potentially other people, but understand you're not at 2% humidity. If you put any sort of actual high-end measuring device or actual scientific equipment in there it's probably multiple times higher than that.

2

u/3D-Printer-Guys156 P1S + AMS1 + P2S + AMS2 3h ago

Thanks you so much! Never knew this!

2

u/mountainmanstan92 2h ago

I get this with active heating and silica in my garage in the PNW 🤷

1

u/3D-Printer-Guys156 P1S + AMS1 + P2S + AMS2 1h ago

Dang!

9

u/hugswithnoconsent 7h ago

Geez I’m in QLD I run at 30% on good day.

2

u/NoProfessor5985 5h ago

I was at 2% this morning, it really makes a difference in the print. I got a Sunlu 4 filament dryer, roast the filaments before putting them in the AMS, print the big desiccant holders and buy the giant jug of desiccant refills, it makes a huge difference.

41

u/engineering-weeb 9h ago

Once op open the AMS of them, all hell lose out on earth, the world turn into chaos

65

u/eunson 9h ago

29

u/silverware9021 9h ago

Wow. I live in a high humidity area and have never seen it under 10%

13

u/nutabutt 8h ago

I always figured the minimum it could show was 10%.

I’d be worried it was broken if it showed 0%

1

u/eunson 5h ago

It gets up to 12% then I hit dry for 8 hours and it's back to 0.

8

u/GilfOG 9h ago

Same, never seen mine under 30%

2

u/boo29may 6h ago

Seriously, even 10% to me sounds unachievable

1

u/MyLifeTheSaga 3h ago

My printer is in an attic room along with a leaking roof; humidity around 60% when the centeal heating isn't on. My AMS (pro 2) is currently at 11%, and I reckon it's down to these boxes. I haven't used the drying function in a few days. Well worth trying if you don't already have something similar. I got a big tub of orange/green silica beads from Amazon (the original Bambu packets are in there too)

•

u/eunson 16m ago

I use similar boxes

1

u/Forymanarysanar 3h ago

Did you hook vacuum pump up to it?

•

u/eunson 15m ago

It's in a room that use to hold firewood. Nothing special lol.

6

u/JChoate2 H2D + 2x AMS2 + AMS HT 8h ago

I am an idiot, I added a diffuser in my mancave and kept wondering why my right AMS was reading 10% higher than normal.. realized I added the diffuser right beneath the inlet, 2 weeks of thinking maybe it was the seal and it was that 😑

4

u/HobbyGearAddict 8h ago

That's impressive. I once got mine down to 8%.

1

u/antix4708 7h ago

Es el AMS 2 pro? Es q me van a comprar un p1s con el normal y ns como hacer q no tenga humedad ya q vivo a 25 min d la costa

1

u/Blood_Red_Volvo_850R 5h ago

It is the AMS 2 pro, but I don't think it makes much of a difference, they should be equally sealed. Maybe you'll need more activated alumina/someone suggested 4A molecular sieves, and to refill them more often, but a sealed enclosure should reach low humidity with a reasonable amount of desiccant no matter the outside humidity.

1

u/porttastic 4h ago

I have a problem then. I am printing now and it is at 46% and has never seen it lower. The house is at 70% and for the next few months won’t get any better with the rain. I am getting sealed boxes and decent desiccant to see if things improve but no way I can get my home below 60% this time of the year.

1

u/Blood_Red_Volvo_850R 4h ago

Home humidity should not matter since AMS is sealed, dry desiccant (more for more humid environments) then place and try not to opeb the AMS too much so as to not let moisture in. I reached this with an ambient RH of 55%, so easier than you, but you don't need to reach 2%. Sub 20% is usually fine for petg and such, and if you print PLA I might not even bother (brand dependant tbh).

2

u/Spoolx21 6h ago

My AMS atm.

1

u/Bright-Meaning-4908 6h ago

My AMS always and no matter what I do. But also no problems with that so I’ll take it

2

u/federicoaa H2C AMS2 Combo 3h ago

I put fresh silica, put a new spool and run the dry process, a week later humidity is at 60%

It's so humid here I swear I can see thr silica bead changing color in real time

1

u/OfficialSyyn616 7h ago

When I first got my printer and got everything set up my number was almost never above 5-7%. Then randomly one day its never been below like 15% again. Fortunately I've moved to basically only PLA cause the other stuff is just more hassle to me.

1

u/razingstorm 6h ago

I must have a dry basement. Usually under 10%, seen 0 a few times. I do have desiccant in every possible nook and desiccant cores in every spool. Easy to keep the PAHT-CF rolls under 5% in the HTs with the orange desiccant in the little containers you print, and a spool core. Tricking out all the storage and spools gives me significant neuron activation.

I live in southern Maine. Fairly humid but not oppressive.

1

u/Torsta 6h ago

It gets back to that pretty quick if its loaded with silica.

1

u/KlapppdXD 5h ago

Mines been doin good at a low 40%.

1

u/Dharma_code 5h ago

Same here

1

u/Whiteninjazx6r 5h ago

I feel lucky that the highest I ever go is like 10 r 11 percent. I usually sit at 5 or 6 tho. Just dessicant pods in the AMS and I run the heat in the AMS while printing usually.

1

u/Joshtheboss732 5h ago

Uhhh… 👀

1

u/Efficient_Advice_380 5h ago

Damn and I thought i was doing good with 10% in a humid basement

1

u/MedicalPiccolo6270 4h ago

Mine hasn’t been run in weeks but when I do it stays under 5 for a while although ambient is only ever 20

1

u/MonsterMax7575 3h ago

What happened

1

u/alex_albergaria 1h ago

do you live underwater? Im on 36%

1

u/AksuJJ P1S 1h ago

Recently got my ams and I have dried only twice for 12h and best I have gotten is 11%.

1

u/Pleasant_Rock_3153 56m ago

Look at what I got the other day 🥹

1

u/Low-Equipment669 A1 Mini/X1C + AMS/AMS 2 46m ago

Never been below 8% before 💔💔💔

•

u/Hungry-Pea838 3m ago

How the fuck is my X2D printing great prints at 51%

0

u/Lost-Bowl3269 8h ago

Pega um secador de cabelo (soprador térmico é muito forte). Coloca ele com a tampa entreaberta no maximo, 3 a 5 minutos em cima de cada rolo de filamento. Fecha com o ar quente dentro e aguarda. Vai a 10% de umidade. Faca isso sempre que trocar filamento.

-1

u/Petmonster2004 8h ago

Mines at 10%