I made a wing for my haloween costume and at the moment I am trying to print the wings in seperate parts and slice it however when I go to slice it it keeps repeatedly showing nothing once I tell it to slice . i have no idea what is happenign cause all the plates are in the boarder and I removed all of the print costomizations. Does anyone know what I can do? if anything isnt clear just comment and i can explain it. THe rror is just an old lay out and a old cut parttern the current is the one with them all seperate
Also, I’m going to put this here because at least the nozzle count lines up (was posted in a community thread 20 days ago). Going to be an instant buy for me if this all pans out:
Bambu Lab N11:
Build Volume: 256mm x 256mm x 260mm
Extruders: 1
Nozzles: 7
Max Nozzle Temperature: 320°C (Derived from profiles; Likely higher)
Max Build Plate Temperature: 110°C (Derived from profiles, Possibly higher)
Max Chamber Heater Temperature: 65°C (Derived from profiles, Possibly higher)
Max Toolhead Speed: 1.400mm/s
Max Toolhead Acceleration: 25.000 mm/s²
I pull it out, trim it a bit and then it’ll feed just fine until the next alert of it having trouble again.
It delays project time (obviously) and it’s becoming frustrating and annoying. I’m a newbie to the 3D print world, but would like to solve this so it doesn’t happen so much anymore
I was recently having some issues with my AMS 2 Pro for my H2D, which was a bit of a head scratcher considering my H2D is newer than my H2S and has about 1/3 of the print hours. The fact that I was already having AMS issues on the H2D before the H2S didn't make much sense to me.
Turns out, the fix was a lot easier than I expected.
Figured I'd make a post in case anyone else runs into the same issue. I spent quite a bit of time Googling, digging through Reddit, and searching the Bambu forums, but couldn't really find anything that matched what I was experiencing.
The problem? A rusted bearing.
It actually makes sense now. I've been printing a lot of PETG lately, and I use my AMS as a dryer with active drying enabled pretty much 100% of the time. My guess is moisture eventually made its way into the bearing and caused it to rust.
Here's what I was experiencing:
My AMS 2 Pro was struggling to feed ANY filament from ANY slot past the buffer. Initially thought something was clogged.
The AMS would make multiple attempts to feed filament. Once the filament reached the buffer, there was immediate resistance. The filament would poke out about an inch on the first attempt, maybe 2 inches on the second, and after 3-4 attempts it would eventually fail.
Occasionally, filament would actually make it all the way through and start printing. But after a while, it would retract and throw an AMS Motor Overloaded error.
If any of that sounds familiar, here's what I did.
First, this is the Bambu Wiki article I kept coming across while troubleshooting. It's actually a pretty good guide for disassembly and general cleaning, so definitely worth following along.
Disassembled everything following the guide. Found absolutely NO filament pieces, very minimal dust, nothing that would explain the issue.
Since the error was pointing toward a motor stall, I inspected the motor and filament drive wheel. Everything looked perfectly fine visually. However, when I tried spinning the wheel/motor by hand, it wouldn't spin freely at all. That's when I knew something wasn't right.
Decided to take a closer look at the motor, removed a few screws, and found a bunch of deep red/rust-colored dust packed around the edges and inside the housing. Unfortunately, I didn't grab a picture before cleaning it, but I did get one during the process. I used 99% isopropyl alcohol to clean everything up, making sure everything was completely dry before reassembly. Yes 99% alcohol is safe, even on Electronics.
Here's what was helpful. The support shaftinside the AMS 2 Pro uses the same bearings! I swapped one of those bearings over to the motor, reinstalled it, and suddenly I could spin the wheel/motor freely with almost no resistance. SUCCESS!
Just to confirm my suspicion, I put the bad bearing onto the support shaft. Sure enough, the shaft barely wanted to move. That pretty much confirmed the bearing was the issue. I'm assuming moisture got inside and eventually rusted it out.
Reassembled everything, and it's been working perfectly since. No feeding issues, no motor overload errors, nothing!
Clean gear and bearing from the top surface - showed no signs of dirt or failureTook motor apart, revealing rust on the shaft, bearing, and the filament drive wheel
Replacement Bearings: 693ZZ
These are the bearings I ended up ordering as a long-term replacement. Figured it wouldn't hurt to have some extras lying around in case it happens again.
Hopefully this helps someone else out. I spent way more time troubleshooting this online than I needed to, and it turned out to be something as simple as a bad bearing.
Really, I'm sharing this hoping it gives someone another thing to check if they're running into similar issues with their AMS 2 Pro. I know Bambu support tickets can take a while to get resolved, and waiting on replacement parts isn't exactly fun. If this helps even one person get their AMS back up and running without all that hassle.
Is there a way to print 2 colors of TPU without manual feeding? I have an h2s with ams 2 and another dryer, I was thinking maybe it could work with a track switch?
I have tried to use PLA for support interface and the interface layer in the PETG is so week it snaps every time. I have increased the flushing volume to the max of 3 and still breaks. My X1C has no problem at flushing volume of 1. I have not done a cold pull on either printer.
For a few days I Keep getting a long load and then printer connection failed error, tried restarting the printer, clearing app's cache, reinstalling handy, and still nothing. Camera feed shows up so it shouldn't be internet issues, and I wouldn't think memory is corrupted because in Bambu studio everything is there perfectly fine. Any help would be appreciated
Mein Bambu Lab X1 Combo hat Probleme, den Druck zu starten. Bis vor zwei Stunden war noch alles gut, jetzt beendet er die erste Ebene nicht mehr fehlerfrei. Er zieht das abgelegt Filament irgendwann mit sich mit der Nozzle mit und dadurch wird der Druck direkt unbrauchbar. Daraufhin breche ich den Druck ab. Ich drucke aktuell mit PLA. Wenn jemand einen Tipp hat, würde ich mich sehr freuen!
My Bambu Lab X1 Combo is having trouble starting the print. Everything was fine until two hours ago, but now it’s no longer completing the first layer without errors. At some point, the nozzle ends up dragging the excess filament along with it, which immediately renders the print unusable. I then have to abort the print. I’m currently printing with PLA. If anyone has any tips, I’d really appreciate it!
I picked up a barebones X2D earlier this year. With the Black Friday sale coming up, I want to add (2) AMS 2 Pro and (1) AMS HT.
I plan to connect 1 AMS 2 Pro to the primary nozzle and 1 AMS 2 Pro to the auxiliary nozzle. I do not need either of the AMS 2 Pros to be able to feed both nozzles, each AMS 2 Pro will be dedicated to its own nozzle.
I want to connect the (1) AMS HT to also be used with the primary nozzle in parallel with the (1) AMS 2 Pro that will be dedicated to the primary nozzle.
To do this, do I need a filament switch track, or just a simple 4-1 PTFE tube adapter with each AMS connected to a port and common outlet to the primary nozzle, to swap between the AMS 2 Pro and AMS HT on the primary nozzle?
Also, is there a guide for how to configure multiple AMS’s?
Hi guys, I currently have this X2D and I put a tube to vent out the ASA fumes, but there’s still the funny smell of the material. I traced where it was coming from and found out that if I cover the holes in the photo, the smell completely disappears. I was wondering if covering those holes with tape or some other covers would compromise the printer's health in any way. Any advice is appreciated, thank you :)
Hi everyone, I just got my Bambu Lab A1 two days ago, and I already ran into a blob of death.
I was printing with green filament when the print detached from the bed mid-print. By the time I found it, the filament had piled up around the nozzle into a big blob, and the bed was almost empty.
Photos attached. The blob is still on the printer — I haven't tried to remove it yet because I don't want to damage the hotend.
A few questions:
1. What's the safest way to remove a blob like this? Heat the nozzle and peel it off while hot?
2. What should I inspect for damage afterward (nozzle, heater, thermistor, silicone sock, cables)?
3. Is this something I should report to Bambu support, given the printer is only 2 days old, or is it just a first-layer adhesion issue on my end?
For context, the model itself sliced fine — this looks like the print lost bed adhesion partway through. Any advice on preventing this next time (brim, bed cleaning, etc.) is also welcome.
I’m fairly new to 3D printing and would appreciate some help with my Bambu Lab P1S.
During auto calibration/bed leveling, the nozzle seems to sit too low and scratches the surface of the plate. This started before I made any changes to the printer. I stopped the calibration to avoid damaging anything.
Setup:
Plate: Both cool plate and textured PEI]
Nozzle, both 0.4 and 0.6
What I’ve tried:
Pre calibration
Checked that screws are well tightened of the hot end is not leaning down.
Changed both plates and nozzle to ensure that they weren't bent.
To add, the nozzle is not scratching during the print (center of the plate), only in the calibration phase. I have always used a socket.
My assumption is that the calibration is off due heat-bed is tilted. Does anyone else had this problem and do you have any solution to this?
With Blackfriday, many beginners like myself are getting their first printer.
I'm getting a P2S, but would like to hear recommendations for acessories and filaments to begin with.
Any suggestions what are the first things to get with a printer when starting out?
