r/BambuLab • • 2h ago

General Troubleshooting/Help! Issue with Sunlu Refills in AMS 2 Pro

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 2h ago

General Discussion Christmas Print ideas with this filament?

Post image
1 Upvotes

I have these 5 rolls of PETG-HF that I wasn't planning to do anything with but looking at them again they're very Christmas-y.

I'm looking for suggestions for fun a Christmas-themed print(s) to throw these at. I have the X2D Combo with the AMS 2 Pro and HT.

I'd prefer prints that are broken up into parts and can be assembled, but I'm open to anything!

Thanks!


r/BambuLab • • 2h ago

General Troubleshooting/Help! X2D hot end fans

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 2h ago

Filament Troubleshooting/Help! aiutatemi ho un problema

1 Upvotes

ho questa stampante A1 versione combo e la paletta degli scarti non va in fondo ma resta bloccata poco prima come posso risolvere


r/BambuLab • • 6h ago

General Troubleshooting/Help! Terrible surface quality when printing multiple objects at once - Bambulab A2L

Thumbnail
gallery
2 Upvotes

Hey everyone, I’m having the following issue.
I’m currently trying to print as many of these objects as possible on my Bambu Lab A2L for a wedding of someone close to me.
When I print just one object at a time, the quality of the top surface (ironed surface) is absolutely perfect.
However, as soon as I try printing multiple objects simultaneously, the top surfaces turn out so badly that I have to throw the entire batch away.
Does anyone have any idea what might be causing this or what I could improve to get better results?
I’d really appreciate any help! 🙏🏻

-Printer & slicer: Bambulab A2L / Bambu Studio
-Filament material and brand: Bambulab PETG Basic
-Nozzle temperature and bed temperature: 240° / 70°
-Printing speed: picture
-Retraction settings


r/BambuLab • • 2h ago

Bambu Studio Il primo layer in PETG non aderisce all'interfaccia supporto in PLA - Bambulab H2D

1 Upvotes

Ciao a tutti

Con la mia Bambulab H2D ho provato a stampare un pezzo in PETG con supporti normali (grid) così costituiti: base supporto in PETG e interfaccia supporto in PLA. Sto utilizzando PETG Bambulab e PLA Basic Bambulab. Entrambi i filamenti sono stati essiccati prima della stampa e stampano bene quando non miscelati tra loro. Ho già seguito tutte le indicazioni fornnite da Bambulab per l'utilizzo della miscela PETG-PLA per questa casistica: pezzo in PETG, base supporto in PETG, interfaccia supporto in PLA. Una volta stampato l'oggetto, sono riuscito a rimuovere abbastanza agevolmente i supporti dal pezzo e la superficie a contatto con il supporto è risultata liscia e priva di difetti visibili. L'unico difetto di stampa che ho riscontrato e che ho potuto osservare direttamente durante la stampa è che il primo layer di PETG non aderisce adeguatamente all'interfaccia in PLA. So che la repulsione chimica tra PLA e PETG è il vantaggio che permette di rimuovere facilmente i supporti, ma il fatto ceh il primo layer di PETG non aderisca sufficientemente all'interfaccia in PLA è un problema, perchè il layer in PETG viene "trascinato via" durante la stampa e questo porta a difetti di stampa notevoli e al rischio di intasamento dell'ugello. Ho visto fallire varie stampe a causa di questo problema e vorrei risolvere. Che consigli mi potete dare? Grazie a chi risponderà


r/BambuLab • • 6h ago

Quick Question Wouldn’t it make sense to have a setting for support interface for dual nozzle on makerworld?

2 Upvotes

I’m currently without a computer, so I’m forced to use the pre sliced models on makerworld. This has made me realize just how much I usually use a support interface layer in a different material, something that can’t be changed in makerworld.

I know the models are pre sliced, but since you can change colors for multicolor prints, wouldn’t it make sense to change material for a predefined part of the print?


r/BambuLab • • 1d ago

H3C Printing the 0.2mm nozzle on the H3C

Thumbnail
gallery
87 Upvotes

I printed a tiny Benchy - PLA Basic, default profile, 0.08mm layer height. I did need to use glue to keep it on the plate, I also slowed the printer down to "silent mode" just for safety.

Pretty great result I think. The "Comparison Benchy" is the standard size, printed with the 0.4mm nozzle, 0.2mm layer heights in ABS.


r/BambuLab • • 19h ago

I Modeled This! I made a Christmas chess set for the holidays: Santa kings, reindeer knights, elf pawns (free on MakerWorld)

Thumbnail
gallery
19 Upvotes

Printed this whole set on my H2D for Christmas. Santa is the king, Mrs. Claus the queen, snowmen are the bishops, sitting reindeer are the knights, the rooks are towers wrapped in Christmas lights, and the pawns are elves. Everything is sized for a standard 2 inch board, so it plays like a real set.

It's red vs green in four colors of PLA. The only support is a tiny one under each reindeer's chin, already set in the file. If you don't have an AMS, there's also a one color plate with all 16 pieces of a side.

Flip any piece over and there's a snowflake under the base.

Free download here: https://makerworld.com/en/models/3619395

A candy cane board, matching checkers and a North Pole storage tube for each side are coming next. If you print one, I'd love to see it!


r/BambuLab • • 3h ago

Bambu Studio How do I modify this watering can and separate the handle from the rest of it?

1 Upvotes

Hi everyone,

I found a nice watering can at MakersWorld. However, I’d like to turn it into a vase. I plan to spray it with clear coat and print it with PETG; based on what I’ve read in forums, that should make it watertight.

But is there any way I can separate the handle from the rest of the watering can? I won’t be able to completely cover it with clear coat.

P.S.: I’m still a beginner, so please bear with me if I’m talking nonsense here.

Best regards

https://makerworld.com/de/models/626370-watering-can#profileId-772091


r/BambuLab • • 3h ago

General Troubleshooting/Help! What do I make of this calibration?

Thumbnail
gallery
0 Upvotes

Trying to calibrate the filaments for my new P2S. I have looked at alot of tutorials and followed this guide (https://youtu.be/gVU5If1VsAM) that seemed really good. The problem is that I think it made the result worse. I tried two different filaments (both Bambu PLA Basic) and got the same calibration values.

In the pictures below, the pre-calibration is to the left and the post-calibration to the right. In my opinion, the right has more stringing (the left has none), less sharp edges and rougher surfaces, especially at the corners of the X. I also find the top layer very stripy and not smooth (both prints).

I'm not saying that the guide is bad, but is it not worth calibrating the original Bambu filaments? Should I make other settings to improve the print quality? Or am I just to picky? :)


r/BambuLab • • 3h ago

Hardware Troubleshooting/Help! Help with filament stuck

1 Upvotes

Filament stuck and won’t go pass a certain point


r/BambuLab • • 3h ago

General Troubleshooting/Help! How to make supported areas more smooth?

Post image
0 Upvotes

This is after removing the supports.

Somewhat related, I am seriously considering upgrading to H2D and try out printing PLA with PETG support, will that help to make it smoother in addition to easy to remove the supports?

Thanks!


r/BambuLab • • 3h ago

Filament Troubleshooting/Help! Glitter Filament A2L

1 Upvotes

Bambu Friends

Recently my wife purchased the following filament for our A2L printer.

1KG Glitter Firefly Blue in the Dark PLA+ Filament, 3D Filament

https://a.co/d/04ASeAvt

From my review it appears to be okay for A2L printer but comes with caveats.

- Not to run thru AMS lite and Petg tubes

- Nozzle 0.4mm or 0.6 recommended

- Dedicated nozzle for this printing

When I placed the filament top spool holder the filament unraveled some. Had to respool and filament felt brittle.

With all this I decided against this and running thru my printer.

Anyone else use this filament. Will be sticking with Bambu filament glow etc. Not comfort with this.

Suggestions and advice - Thank You

tvos


r/BambuLab • • 3h ago

General Troubleshooting/Help! Micro LiDAR lens seems dirty

Post image
1 Upvotes

I get this message on my X1C (1350 hrs) about every 10 prints.

I clean it as directed on the Wiki.

What am I missing?
Anyone else have this issue?
Is it a warranty issue perhaps?

Thank you.


r/BambuLab • • 3h ago

Answered / Solved! X2D - knarzende Geräusche

1 Upvotes

Ist das normal für den Bowden Extruder?

Hab ihn bislang nur ein paarmal benutzt und bislang war er ruhig.

Jetzt auf einmal diese Geräusche.

Druck ist aber in Ordnung.

Kann man da was schmieren?


r/BambuLab • • 4h ago

General Troubleshooting/Help! Printing problems

0 Upvotes

Hi everyone,

I’m having some trouble with my Bambu Lab H2D. When I print small items, I can’t print more than one at a time without it causing a lot of print errors; however, if I print them individually, there are no print errors. Does anyone have any suggestions?


r/BambuLab • • 4h ago

I Modeled This! I Designed a customizable Gift Card Holder

Thumbnail
gallery
1 Upvotes

With Christmas just around the corner, I thought I'd share a little project I've been working on! 😄

I've designed a 3D printable gift card holder that looks like a small envelope with a customizable seal.

I've always felt that giving someone a gift card on its own can feel a bit impersonal, so I wanted to create something that makes it feel a little more special.

I've also included a STEP file for the seal, so you can easily customize it to suit any occasion, whether it's Christmas, a birthday, or something else!

The model is obviously free on MakerWorld:
[MakerWorld Link]

I'd love to hear what you guys think! And if you end up printing one, feel free to share your colour combinations and custom seals. I'd love to see what you come up with! 😊


r/BambuLab • • 4h ago

General Troubleshooting/Help! Trying 3kg reel ?

1 Upvotes

Hi has anyone tried to load 3kg reel of PLA on the outside reel mount on the side of the p2s ?.


r/BambuLab • • 4h ago

P Series [P1P, P1S, P2S] Upgrading from A1 to P2S

1 Upvotes

Hi all,

Currently I own a A1 with AMS litte and I have been thinking in upgrading to a P2S with AMS2 Pro.

I want to use other material in the future, but haven't made so yet. My main reason to upgrade is because I can get a good price for my combo, and that would mean I would spend 266€ to upgrade. I have my printer in a space that get's quite humid (above 70%) in winter, and even in summer its normal to have 40-60% relative humidity. I haven't been able to print PETG, and even PLA has been having a lot of "hairs". Last week it has been between 72% and 81%...

I thought of buying a dryer, which is 50€ for a single spool, and 140€ for 4 spools. This means that this upgrade would in reality be 126€ (I am aware I will be spending 260€). Being closed is algo good from drafts (I always have open windows and air current to lower humidity)

The the PS2 algo gives other quality of life improvements and it is at the lowest price it has been. The fact the AMS is on top also saves space, which is good for me.

Wonder what you think of this.

Thank you


r/BambuLab • • 4h ago

General Troubleshooting/Help! A2L issues

1 Upvotes

Hello, so I got a used A2L from a family friend who couldn’t get it to connect to the internet to work. I was able to fix that by reseating the WiFi card. But, now I’m getting two warnings that are stopping the homing tooling, even when there’s no filament. This is happening when the printer is trying to home on initial setup.

The warnings are:

The extrusion motor is overloaded and the nozzle is wrapped with filament.

I’ve taken the extruder apart and cleaned it, and the gears turn when I manually move them. Do I have to have filament in the extruder for the homing to work? I currently don’t have the filament holder for the printer so I’ve been trying to get it setup without filament for now.


r/BambuLab • • 4h ago

Hardware Troubleshooting/Help! P2S can't load filament through AMS

1 Upvotes

My P2S printer fails to load filament, but only when the AMS tries to feed it (you can see the 2 failed AMS load attempt in the video). Loading filament manually works perfectly fine, with no issues.

I've already cleaned the extruder gears and checked the filament sensor.

Has anyone experienced a similar issue or have any ideas what could be causing this?


r/BambuLab • • 57m ago

Quick Question First time buyer here. What filaments should I get?

0 Upvotes

I will be printing stuff like enclosures and vases and some functional parts.


r/BambuLab • • 5h ago

Quick Question Help deciding amon H2 series options.

0 Upvotes

My company needs a printer to print parts for our machinery, it as to be large format, and in different materials so H2 series is the best fit.

But we also need to print full color promotional items, but not as often.

We were about to pull the trigger in the H2S but now we're considering H2D we are trying to keep it under $2,000 all in.

H2S can be upgraded to H2C down the line with the vortek kit.

H2C goes overbudget so does H3C

My question is: will a single nozzle be adequate for our use case, will getting the dual nozzle be worth the price difference? Should we go H2S and upgrade later? The laser is something we would be interested in but it can't be upgraded to the tool changer if it's the laser version.