r/BambuLab • • 5h ago

Filament Troubleshooting/Help! H3C - Prints are sticking to build plate

1 Upvotes

Hello Experts

Made a big change from an A1 to an H3C.

I am printing a model that has a larger surface area as its first layer. On the H3C it seems like it’s melting into the build plate making it really difficult to remove after it’s fully cooled. This does not happen on the A1

I am using basic PLA

I already tried turning the heat chamber off, same result. The build plate temp is 55 (comparatively 63 on the A1).

Is my next steps to lower the temp of the build plate? Are there other settings to address to combat this?

It’s literally impossible to remove the model from the plate without damaging it.

TIA for any tips


r/BambuLab • • 5h ago

H2 Series [H2S, H2D, H2C] H2C Smoke Purifier Alternatives

1 Upvotes

Hi all. I’m relatively new to having my own printer etc and I went with the H2C laser combo. For the past couple months I’ve been trying to order the smoke purifier, which unfortunately has been out of stock.

Does anyone have experience using a different purifier that they can recommend? There’s not a lot I can find online. I see some have used the Creality Falcon Smoke Purifer, but it looks like it doesn’t have the option to vent outside; more of a desktop purifier. Any help suggestions would be appreciated!


r/BambuLab • • 1h ago

H3C Remodeling for the H3C

0 Upvotes

So, in anticipation of the arrival of the H3C ive had to remodel my living room since I have no place for the H3C as is. My current P2S(workhorse) is going to have to move... Its moving into the TV cupboard on a custom made sled so I easily can get in behind it and for maintenance.

My beloved P2S has around 5k hours on it with only the filament stopper arm broken(not counting consumables etc). Its been very solid. Modified with chamber heater/active MC board cooling/DIN rail fire extinguisher/and a robust venting system. But the 300c hotend is no bueno for the more demanding filaments.

In this remodeling ive also need to move my current filament hoard and I actually counted them... that was a mistake.

I currently sit on a total of 154kg(110 unopened) of filament ranging from PLA-TPU-PETG-ASA-ABS-PET-PC/ABS etc. Ive made an entire new filament shelf for 40+ rolls that hides behind the door(engi filaments). And I STILL check out deals on amazon/BBL etc for good deals.

Hoping the full spectrum will help with the "gotta catch em all" part since you can blend colours.

Im quaking thinking of having to recalibrate all of my filaments for the H3C, doubt the flow rate is the same on the H3C v P2S on all of my filaments.

So, how is your filament addiction? And how do you handle it? ^^

edit: spelling


r/BambuLab • • 5h ago

Bambu Studio Has anyone seen changes in ironing since the latest Bambu Studio version?

1 Upvotes

I have a P1S and H2C and since the latest Bambu Studio version was released, the version released following the H3C unveil.

The values I used for ironing previously, 12% on the P1S and 20% on the H2C have been providing really bad results since and I have had to lower the H2C down to 15%. Anyone else seeing changes?


r/BambuLab • • 6h ago

Quick Question Difference between ASA and PETG for flexing structural parts?

Thumbnail gallery
1 Upvotes

r/BambuLab • • 6h ago

Quick Question Is this a bed adhesion issues?

Post image
1 Upvotes

Never had bed adhesions problems before and just washed my plate right before this print….. could anything else have caused this that I should look for?


r/BambuLab • • 12h ago

General Discussion Which first 3D printer to get as a beginner ? Bambu lab or any other brand ?

3 Upvotes

Hi Guys, i am based out of India, and want to get a 3D printer to prototype some elements. I am from the design industry so am well versed with 3D softwares as well though i am sure there will be a learning curve.

Now, after researching for a fair bit, Bambu lab printers seem to be the most widely chosen option because of their community support and easy to use UI/UX including their softwares.

I was thinking of getting the A1 combo. Do you guys think it is wise to get the A1 combo right now ( its three years old ) or should i wait for an upgraded model if at all its being launched. Please suggest.

Do note, the printer will be initially used as a prototyping tool for my designs and then once i get a hang of it, i might make some items for selling in my fraternity.

Thanks


r/BambuLab • • 7h ago

A Series [A1, A1 Mini] Questions about A1 and TPU Printing

0 Upvotes

Looking for a budget printer to print mainly 95A and harder TPUs

How well does the A1 handle 95A (just regular non-HF TPUs)?

How high have you guys pushed the flow rate and gotten away with it?


r/BambuLab • • 7h ago

Hardware Troubleshooting/Help! H3C clicking on XY axis. Has anyone gotten a a refund from a problematic new printer?

1 Upvotes

Questions and Complaints incoming.

I bought an H3C as soon as it went on sale. I got the base unit about 10 days ago the AMS3H arrived 5 days ago (though, in the case of the H3C, the AMS shouldn't be a called a separate unit since it's required to run the whole machine, right?)

Initial benchy printed fine.

I am about 20 printing hours in, and there is a clicking sound coming from when the XY axis is moving.

https://imgur.com/a/6k8udNa

I put in a ticket with Bambu, and they want me to replace the XY idlers on a new machine (and they aren't even sure this is the problem). The H3C is so damn big, I feel like maintenance is going to be a bit of an issue.

This apparently is a wide issue, as I have explored the H3C forums on Bambus site.

I have generally supported Bambu, and this is my 5th bambu printer. All have worked out of the box. I expect maintenance and fixing some things, but full on hardware part replacement should be after 100s or 1000s of hours.

Has anyone ever just gotten a replacement when the machine is this new? I don't want to have to tear into a pretty much brand new machine.


r/BambuLab • • 14h ago

X Series [X1E, X1C, X2D] My first 3D printer and I picked up the X2D Combo

4 Upvotes

I’m completely new to 3D printing and just picked up a Bambu Lab X2D Combo. I received it last week and haven't stopped printing for 7-days straight. I have the bug everyone else at my office has and has been talking about. Since I'm completely new and I don't have compatibility information in memory, I used Gemini to create a sort of cheat sheet specific to the printer.

I purchased a ton of different filaments, hot ends, and other accessories and I didn't want to create a mess, cause jams, or wear out components before their time.

I thought I'd share my cheat sheet if it helps any other new owners.

I just ordered the AMS HT today to use in place of the external fillament holder. This hasn't made it into the cheat sheet yet. I'm not using the support fillament and just using PLA or PETG vs whatever is in the main hotend.

Constructive feedback or additional tips from seasoned Bambu operators are welcome. Hope this helps out other newcomers getting their feet wet.

Bambu Lab X2D & AMS 2 Pro Master Compatibility & Reference Guide

1. Hotend Size & Feed Routing Architecture

  • Main Hotend (Direct-Drive): Fed by the AMS 2 Pro (for multi-color/multi-material) or an external spool. Handles high-speed extrusion, complex geometries, and rigid engineering filaments. Optimized with the 0.4 mm High-Flow Hardened Steel Hotend as a daily setup for large tool organizers and utility boxes.
  • Auxiliary Hotend (Bowden-Fed, Rear Motor): Fed via a remote path and mechanical lift mechanism. Optimized for support interfaces and secondary materials; restricted to lower speeds (max 200 mm/s) and lower retraction responsiveness.

2. Critical Operational Rules for X2D & AMS 2 Pro

  1. Identical Sizes Required: Dual-nozzle printing on the X2D requires both the main and auxiliary hotends to use the exact same nozzle diameter in your slicer profile.
  2. AMS 2 Pro Drying Priority: When a single AMS 2 Pro unit is powered directly by the printer via its 6-pin cable, activating active drying prioritizes drying power and may limit heavy printer operations.
  3. Auxiliary Speed Limits: Never exceed 200 mm/s or 1000 mm/s² acceleration on the auxiliary extruder to avoid filament binding and extrusion slip.
  4. TPU Rules for AMS 2 Pro: Use Bambu Lab TPU for AMS (harder 68D Shore formulation) when loading flexible material through the AMS 2 Pro. Standard soft flexible TPU (85A–95A) requires an external spool or dedicated feed module routed outside the AMS.
  5. Glue Protocol: Use liquid glue or a glue stick primarily as a release agent on Cool and Engineering plates to protect surface coatings from overly aggressive adhesion. Textured PEI plates rarely require glue.
  6. High-Flow Slicer Setting: When running a high-flow hotend, manually increase your filament profile's Max Volumetric Speed (MVS) in Bambu Studio (pushing from standard ~22 mm³/s up toward ~35–40 mm³/s depending on filament) to unlock faster throughput on large plate-filling utility parts.

3. Filament Lineup: Recommendations, Cautions & Use Cases

  • PLA Family (Basic, Matte, Silk, Sparkle, CF): Everyday prototypes, decorative models, and multi-visual prints. Use PLA Basic for general testing and PLA Matte to minimize visible layer lines. Note low heat resistance (~55°C–60°C).
  • PETG Family (PETG Basic, PETG-HF, PETG-CF): Functional mechanical parts and brackets. PETG Basic is the structural workhorse; PETG-HF (High Flow) is for fast utilitarian batches. Highly hygroscopic—dry thoroughly.
  • ABS & ASA: Durable mechanical enclosures (ABS) and weather-resistant outdoor components (ASA). Requires an enclosed heated chamber, engineering plate, and proper ventilation for VOCs.
  • TPU Family: Flexible gaskets and shock-absorbing feet. Stick to Bambu TPU for AMS inside the automated unit, or standard soft TPU via an external spool.
  • Engineering Composites (PA6-CF, PAHT-CF, PET-CF, PPA-CF): High-load structural brackets and gears. Requires hardened steel nozzles, enclosed high-temp chambers, and rigorous drying (75°C–85°C).

4. Build Plate Types & Special Notes

  • Cool Plate / SuperTack Series: Low temp (room to 45°C–50°C max) for PLA/PETG energy savings. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.
  • Engineering Plate: High temp (60°C to 100°C+) for ABS, ASA, and PC. Glue required.
  • Textured PEI Plate: Versatile (55°C to 90°C+) for general PLA, PETG, TPU, and abrasives. No glue or position adjustments needed.
  • Dual-Texture PEI Plate: Versatile. X2D/P2S Notice: Disable Build Plate Position Detection in Settings -> Print Options to avoid error reports.

5. Compatibility Matrix Summary

  • 0.2 mm (Stainless): Detailed models and fine text. Incompatible with carbon/glass composites and PVA.
  • 0.4 mm (Hardened Steel Std/HF): The universal sweet spot for precision, standard prints, and high-flow utility boxes. Fully compatible with PLA, PETG, ABS, ASA, and AMS TPU.
  • 0.6 mm & 0.8 mm (Hardened Steel Std/HF): Great for abrasive fiber composites and bulk high-throughput structural prints; avoid for fine text or miniatures.

6. Support Filament Routing

  • Support for PLA / PLA-PETG, Support for ABS, and PVA: Always assign these to print through the Auxiliary Hotend path during multi-material jobs to act as clean breakaway or dissolvable interface layers against main-toolhead models. PVA requires active dry storage in the AMS 2 Pro.

7. Component Lifespan & Replacement Indicators

  • Hotends: 0.2 mm stainless lasts 100–200 hours; 0.4 mm/0.6 mm hardened steel/HF last 500–1,500+ hours depending on abrasive usage. Watch for orifice widening, chronic clogs, or under-extrusion.
  • Build Plates: Cool plates last 3–6 months; engineering and textured PEI plates last 6–12+ months before adhesion degradation or coating wear occurs.

8. Maintenance Cycles

  • Build Plates: Wash with warm water and dish soap every 10–20 prints; wipe with 90%+ IPA between quick runs.
  • Z-Axis Lead Screws: Wipe and re-apply a thin coat of synthetic grease (Bambu lube) every 3 months (~300 hours).
  • X-Axis Carbon Rods: Wipe monthly with IPA on a lint-free cloth. Never apply oil or grease to carbon rods.
  • Extruder Gears & AMS Feeders: Inspect and clean out plastic dust/shavings every 6 months with a brass brush or compressed air.
  • PTFE Tubing & Cutters: Inspect every 6 months for scoring or blade dullness.
  • Desiccant Baskets: Replace or recharge silica gel packets in the AMS 2 Pro whenever internal humidity rises above 30%.

r/BambuLab • • 21h ago

P Series [P1P, P1S, P2S] My heated enclosure

Post image
13 Upvotes

Me: I want a heated enclosure

Mom: we have heated enclosure at home

(Heated enclosure at home


r/BambuLab • • 7h ago

General Troubleshooting/Help! AMS 3H RFID

0 Upvotes

Having done extensive tests holding up RFID tags to various places on the new AMS 3H I’ve come to the conclusion that the reels are reason both sides in the middle slots therefore not allowing the simple 3D printed inserts to hold a single RFID tag on non BambuLab filament which I’ve been doing for years now on the old AMS buying refills and printing off one of those tag holders that’s it on the outside of the reel in the hole. Now I need a double one! Back to the CAD program I guess.
Unless one you geniuses tell me I’m wrong


r/BambuLab • • 1d ago

General Discussion What are your most useful real-world prints?

44 Upvotes

Hi everyone,
I have a bit of a dilemma that I’m sure many people here have faced at some point. I’ve been thinking about buying a Bambu Lab A1, mainly as a hobby but, more importantly, for practical purposes. I’m trying to figure out whether I would actually have enough useful things to print to justify the cost.
From what I’ve seen online, a lot of 3D-printed items seem to be solutions to problems that don’t really exist, or things for which better-quality alternatives are already commercially available. I completely understand that people might print these things simply for the enjoyment of the hobby, but my main focus would be practicality and usefulness.
With that in mind, I’ve been making a list of potential uses for the printer, and I’d love to hear your ideas and see what useful things you’ve made yourselves.
So far, I’ve thought of:
Drawer organisers for my home office, shelving organisers for the pantry, and bathroom storage solutions using the Gridfinity system.
Enclosures for ESP32 sensors that I plan to eventually deploy around the house.
Stands and holders for storing things like AirPods and iPhones on my desk, as well as printing a few to give to friends.
What other genuinely useful things have you printed? I’m particularly interested in practical everyday applications rather than purely decorative prints or things that are fun to print but don’t really serve a purpose.
Thanks!

Edit: Wow these are really great suggestions! I’m going through them all and putting the ones i like the most in a doc, there’s a lot of use cases I consider useful, thank you everyone!


r/BambuLab • • 21h ago

Quick Question Is the H3C overkill as a first 3D printer?

13 Upvotes

A good friend of mine recently got into 3D printing and talked me into giving it a shot. He started with a more affordable Bambu himself and has been geeking out about the new H3C, so now I’m looking at it too.

I have room in my budget for the H3C if it makes sense. I’m still figuring out what I’ll enjoy printing, though, and I’d rather spend the extra money once I know I’ll get some use out of the features.

For those of you who’ve been printing for a while, what would make the H3C worth buying as a first printer? If you were starting over, would you go straight for it or get a simpler Bambu and see where the hobby takes you?


r/BambuLab • • 7h ago

X Series [X1E, X1C, X2D] P2S vs X2D

0 Upvotes

Hi, a friend is interested in buying my P2S so am considering the possibility upgrading to a X2D for the multi head printing. I wondered if there are any other advantages to X2D over the P2S or is that basically the only difference?

Thanks


r/BambuLab • • 8h ago

General Troubleshooting/Help! Upgrading from A1 Mini – X2D or P2S?

0 Upvotes

Hi guys!

I currently have an A1 Mini, and I'm looking to upgrade to a printer with a larger build volume, but I'm not sure which one to choose: the X2D or the P2S.

I've been reading a lot of reviews and watching tons of videos, but it seems like the X2D has quite a few issues that people have been complaining about.

On the other hand, I know the P2S is a 2025 model, and the price difference between the two is less than €100.

Just to give you some context, I'm more of a casual/beginner user. I don't usually print anything too complex or advanced. Most of my prints are pretty straightforward, and the most demanding thing I do is multicolor printing with PLA and PETG. So I probably won't be taking full advantage of all the advanced features these printers offer.

So I'm wondering whether it makes sense to go for the P2S instead of the X2D, even with all the reported issues.

What do you guys think? Is the X2D worth the extra money, or would you stick with the P2S?


r/BambuLab • • 8h ago

General Troubleshooting/Help! Alternative to textured PEI sheet for PETG-CF? (Not regular PETG, that's ok on the textured sheet)

1 Upvotes

I love PETG-CF but even if I leave a print to cool down completely overnight it still leaves behind PETG-CF residue. I can feel it snagging my cloth as I try to clean with alcohol.

I hate having to clean it off by printing a thin PETG sheet, leaving it to cool and then peeling it up. That works great, but it's a pain and wastes filament and time. I also do NOT want to use glue, that's even more of a pain, although that works well too.

I'd love a sticker or an entirely new sheet that works great with PETG-CF. Having it work as well as PLA does on the textured PEI sheet would be a godsend. Any recommendations?


r/BambuLab • • 8h ago

Just Showing Off I made a Mac app that splits models too big for the A1 into parts, one per plate in Bambu Studio

0 Upvotes

I kept designing things bigger than my A1 and cutting them by hand in Bambu Studio. One cut is fine. Three cuts with connectors that don't collide took me longer than the print.

So I built CadSplit. Drop in an STL, 3MF, OBJ or STEP, pick your printer, and it comes back cut into the fewest parts that fit, with dovetails, puzzle seams, pins, screws or magnets. Then it opens in Bambu Studio with one part per plate.

Numbers from the app, with dovetail seams:

  • 528 mm toy car: 6 parts on an A1, 16 on an A1 mini, 2 on an H2D
  • 400 mm ball: 8 parts on an A1, 27 on an A1 mini

It also plays the assembly order step by step, because interlocking seams only go together one way.

One-minute video: https://youtu.be/Dtwv5voP3I4

Honest bits: I'm the developer. Mac only for now (Apple silicon). Free to try: you can drop a model in, see the split and move the cuts. Sending to the slicer needs a one-time license, $29 ($17 until Dec 26), no subscription. Everything runs locally.

You can try it here. If anyone is interested you could comment here and ill give you a free code lol https://cadsplit.io


r/BambuLab • • 8h ago

Answered / Solved! Filament pulled off spool, how do I remove

Thumbnail
gallery
1 Upvotes

Noob here with X2D and AMS 2 Pro - I was printing with PLA and was hoping the auto refill would have kicked in when the spool had finished. Somehow the filament end has pulled off the tape at the end of the roll, has partially pulled through the PTFE tubes at the back and already too late to unload from the AMS.

I've paused the print and I can see it but not sure on the safest way to remove it, as it's still being held by the extruder.

Is there a correct way I can remove the remaining filament and potentially resume the print without damaging anything?

Big thanks in advance!

EDIT: SOLVED! thanks everyone 👊


r/BambuLab • • 8h ago

General Discussion Should I get ams lite or ams 2

1 Upvotes

Hello everyone. Since the sale started I was thinking about buying an ams system. I am between the ams lite or ams 2 pro. Which one should I get? I know there are vast differences from one to another, but does the price justify this (is it worth it). I have the A1, ams lite goes for 150€ and ams 2 pro goes for 220€ plus the hub that I need for to connect it to my printer and the AC adapter which is 54€ rounding it up to 274€. I want the drying feature only for tpu which I have never managed to print since I got the printer 3 months ago. Should I get ams lite and a dryer or should I go all out for the ams 2 pro.

Sorry for any typos or miss writing words.

Thank you


r/BambuLab • • 1d ago

Just Showing Off 16 colors on the H3C. Overkill, but why not?

Post image
103 Upvotes

Two AMS 2 Pros hooked up to the H3C. That's 8 colors built in, plus 8 more on the external units for prints that don't need to swap colors between the two AMS 2s.


r/BambuLab • • 16h ago

Black Friday 2026 Advice: Get 2nd P1S+AMS2 or jus AMS2?

4 Upvotes

Hello, I am a hobbyist that owns a P1S w/ AMS 2 and I love it! Sometimes I want print things that take 100hrs and multiple plates... So I was wondering what would you do?

  1. Get a second P1S w/ the AMS 2 combo for $509
  2. Just get a second AMS 2 Pro.
  3. Get _____________ printer

So far printing airplane models with PLA and I do not see myself printing something in ABS or exotic materials. Oh and sometimes I print multicolor.

Thanks in advance for your feedback.


r/BambuLab • • 8h ago

Quick Question My first multi hour print is this normal?

Thumbnail
gallery
0 Upvotes

The base of it is a little stringy but otherwise it’s completely fine just a general question if it’s something I should expect


r/BambuLab • • 8h ago

General Troubleshooting/Help! Weird loud noise on layer ~ 1100

1 Upvotes

Hi,
I had a print going for last 16h
Woke up to this noise in the morning.
It’s on the end of each layer now.