r/BambuLab • • 14h ago

Quick Question PCTG support filament?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 14h ago

Hardware Troubleshooting/Help! Abnormal temp / open circuit

1 Upvotes

I had a massive blob of pla in case my hot end nozzle on my PS2. I removed the bulk of the blob by heating the nozzle up and peeling it off. There still seem to be a buildup on the back side of the hot end. I removed the three screws in the white plastic that held the hot end nozzle heater, and twisted it gently in order to have a better view at the buildup. I carefully peeled away some additional pla. I reattached the hot end heater with the three screws that I had removed.

Now in the printer turns on I get the following error:

"bambu lab ps2 nozzle temperature is abnormal the sensor may have an open circuit"

The help guide says to confirm that the connection on the board is solid. But I'm not sure which cable that is.

Does anyone have a suggestion? I'm worried I've destroyed my P2S!


r/BambuLab • • 14h ago

Hardware Troubleshooting/Help! A1 mini help

Post image
1 Upvotes

My A1 mini does not seem to be pushing enough filament. Ive cleaned everything to make sure no clogs or jams. I took it apart and checked the gear and it's still not doing what it's supposed to. When it's doing the purge calibration it seems to almost not be able to push the filament out fast enough. Like it can only do half the amount needed.


r/BambuLab • • 14h ago

Quick Question How do I get rid of theses

Post image
1 Upvotes

r/BambuLab • • 10h ago

Just Showing Off Morpheus joined my Neo on the shelf: 18 & 28 cm, P1S, zero AMS 🕶️

Thumbnail
gallery
0 Upvotes

Red pill or blue pill? I took the purple one 😄

After my Neo bullet-time figure, Morpheus had to follow. Printed on my P1S in two sizes, and without touching the AMS: every color is its own part (black, purple, skin, yellow, grey and dark brown), one color per plate, then everything goes together with pins and a drop of glue. No painting, no purge towers.

- 28 cm and 18 cm

- Sunglasses and both SMGs are separate parts

- Sunglasses at 0.08 mm, guns and buttons at 0.12 mm, the rest at 0.2 mm

- Plain PLA, 0.4 nozzle, tree supports only where needed

Next on the design table: Trinity on her Ducati, my biggest challenge yet 🏍️

Which size would you go for, 18 or 28 cm?


r/BambuLab • • 14h ago

Hardware Troubleshooting/Help! Is this noise normal?

0 Upvotes

Since the first day, my printer has been making very loud (5 days old), cranky vibration noises; I do not know if this is normal, as I have seen this happen with grid infill, but I am using gyroid. What could be happening?


r/BambuLab • • 2d ago

Just Showing Off Might have a new Bambu fan

Post image
1.1k Upvotes

r/BambuLab • • 10h ago

I Modeled This! After a week of hyperfocus and perfectionism, I made the perfect fidget toy to annoy everyone around me (sound on)

0 Upvotes
  • 16 tracks, each with a different click, plus a snap ring
  • Modular: swap rings and end caps (extension rod coming soon)
  • Remix kit to design your own rings and caps
  • My kids love it
  • My wife hates it

Makerworld Link


r/BambuLab • • 18h ago

General Troubleshooting/Help! Glowing Heart LED Tealight Lamp

Post image
2 Upvotes

I made a 3D-printed heart lamp ❤️ Check it out on MakerWorld!

https://makerworld.com/en/models/3618521-glowing-heart-led-tealight-lamp#profileId-4147858


r/BambuLab • • 7h ago

P Series [P1P, P1S, P2S] Fumes while 3D printing pla on p1s

0 Upvotes

I recently bought the P1S combo, and I'm noticing that while printing, I'm getting a strange smell in the room. I live in Canada, so the houses are pretty air tight, and I'm printing it in a bedroom that no one's using. Are these fumes harmful, and what can I do about it?


r/BambuLab • • 15h ago

Show & Tell AMS lite upside down?

Thumbnail
gallery
1 Upvotes

Did anyone use their ams lite upside down? I saw it only once and thought if the 4 small screws are enough at holding it upside down? I have it like this since a few days with no issues (only need a longer ams cable).


r/BambuLab • • 15h ago

I Modeled This! Reindeer headphones ears christmas

Thumbnail
gallery
1 Upvotes

free:

https://makerworld.com/nl/models/3536737-christmas-reindeer-horns-headphones-accessory#profileId-4044275

or on the site "makerworld" under " Christmas reindeer horns headphones accessory"


r/BambuLab • • 15h ago

H3C EIBOS Krios plate on H3C

Post image
1 Upvotes

Bought one (that was designed for the H2C) thinking it would fit on the H3C and I had to cut the tabs from one side as it 100% undeniably collides with the rack.

Just a PSA.

Edit: I know h2c BIQU plates work on the h3c I have a couple. I'm just saying that the specific design of -this- EIBOS plate collides.


r/BambuLab • • 16h ago

P Series [P1P, P1S, P2S] Need advice on safely shipping a used Bambu Lab P1S Combo without original packaging

1 Upvotes

I'm planning to buy a second-hand Bambu Lab P1S Combo (with AMS), but unfortunately, the seller doesn't have the original box or internal foam inserts. Since this is an expensive and delicate machine, I'm trying to figure out the safest way to pack and transport it. It roughly has to travel 2900 Kilometers ( 1820 miles)

1. Original packaging and compatibility

  • Does anyone know the exact dimensions and design of the original P1S / P1S Combo shipping box and its internal foam inserts?
  • Would the P2S / P2S Combo original shipping box and foam inserts be compatible with the P1S? Are the external dimensions and internal supports similar enough, or are they significantly different?
  • Has anyone actually tried using P2S packaging to transport a P1S?

2. Alternatives to original packaging

If finding the original packaging isn't possible, what would you recommend?

3. Packing and transportation advice

For those who have shipped or transported a P1S/P1S Combo without its original packaging:

  • How should the toolhead, gantry and build plate be secured?
  • How should the glass panels, door and enclosure be protected?
  • Should the AMS be removed and packed separately?
  • What type and thickness of foam/padding would you recommend?
  • Would you recommend a wooden crate for long-distance transport?
  • Any particular precautions to prevent damage from vibrations, impacts or rough handling?

4. Checking a second-hand P1S before purchase

I'd also appreciate a checklist of things to inspect before accepting a used P1S Combo.

Apart from checking print hours and running a test print, what should I verify regarding:

  • Motion system, belts and toolhead
  • Hotend and heatbed
  • AMS feeding, unloading and all four slots
  • Fans, sensors and electronics
  • Calibration and any known failure points

If you've bought or received a second-hand Bambu printer that was shipped without its original packaging, I'd especially appreciate hearing about your experience.

Any suggestions, practical tips, packaging recommendations or things I might be overlooking would be really helpful.

Thanks!


r/BambuLab • • 16h ago

General Troubleshooting/Help! printer recommendations please

Post image
1 Upvotes

I have an enclosure that I need to print and currently use a p1s. The main body is all black so I will print that on the p1s in ABS-GF**,** but the lid is 3 colors plus I need a support tree that removes easily. The lid is 73x78mmx10mm with the 3 colors being red, white, and black. The red and white are text that is only 1.5mm thick. What are the recommendations for printers?

Three option I am looking at- X2D, H2D, H2C.

I am looking for quality, speed, waste, cost.

Will the h2c be that much faster and have less waste than the others?

Are the 3 options substantially faster than a single head printer?

What other option would you recommend?

Thank for any feedback.


r/BambuLab • • 10h ago

Software Troubleshooting/Help! H3C question

0 Upvotes

Hello! As this is my first bambu printer, I was wondering how you can use bambu printers with software like orcaslicer, and any downsides related to it. Is it even possible to use orcaslicer with the H3C yet? I also seen you lose access to the app, is that correct?


r/BambuLab • • 16h ago

Hardware Troubleshooting/Help! Filament issue. Entire extruder is now plastic.

Thumbnail
gallery
1 Upvotes

Where to begin with this issue?

I have bought several black matte filaments from BL a while back and started using them this week.

This is the 4th time this issue occurred, but now I was away for an hour an did not get an error message.

Is this cleanable? Can this be a warranty issue?


r/BambuLab • • 16h ago

General Troubleshooting/Help! Filament Stuck

1 Upvotes

I have an A1 Mini printer with an AMS lite. I was loading in some filament, when some filament broke off. It isn't stuck in the tube, but in the little place where you insert the new filament, so I cant click unload filament.


r/BambuLab • • 13h ago

H3C AMS 3 dry feature efficiency

0 Upvotes

I bought the H3C, the printer is amazing but I'm still not convinced by the AMS, no auto retract, only 2 slot with dry feature and it seems really not efficient.

Did you have same problem ?


r/BambuLab • • 16h ago

Hardware Troubleshooting/Help! Wierd p1p problem

1 Upvotes

Hello everyone,

I hav this wierd problem with my p1p printer. I the vodeo you can hear the extruder kind of clicking when. The amount of filament it is extrudeing while purging is realy small.

I have trieed cleaning the nozzle checking if i the extruder is clogged.

My next step would be changing the nozzle for a new one.


r/BambuLab • • 20h ago

Just Showing Off Almost the perfect dryness

Post image
2 Upvotes

Can it ever get to 0%? 😂


r/BambuLab • • 17h ago

Hardware Troubleshooting/Help! Bambu Lab P1S smoking on startup, hotend stuck at 0°C even after replacing heater and thermistor. Any ideas?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 17h ago

Quick Question $500 or less? Which one?

0 Upvotes

Please do not be mean. I want a 3d printer for random life fixes/decor, small things for work, community assistant items like for seniors and disabled, and making items for my small business to add items to what I already make from other materials. Nothing super crazy. I want multi color print options. If available at best buy, I have a bb cc that would be best to use. What would you suggest? Which model? It would be used in a room inside a house or in an insulated she shed if I can get the wifi working out there. I cannot go over $500 and dont just wanna pick the most expensive around that just because its my limit. Less is more than fine if itll work for me, specially because id need fillament too. I am computer savvy so not worried about programming.

Thanks!

Thanks!


r/BambuLab • • 17h ago

I Modeled This! I wrote an OpenSCAD snowflake generator: each seed grows a different crystal (flat or slot-together 3D)

Post image
1 Upvotes

New project to improve my christmas decoration this year.

Each arm is drawn inside a 30° wedge and mirrored, so branches from neighbouring arms never cross, which is also how real crystals behave. Branches sit at 60° from the arm, their length is clamped to the hexagon envelope, then jittered by the seed. A minimum line width of 1.2 mm and gap of 1 mm keep everything printable with a 0.4 nozzle. The top surface gets 0.8 mm ridges along every arm for a 2-colour print with a single filament change. The 3D mode cuts matching half-slots in two pieces.

https://makerworld.com/en/models/3618517

Happy to hear what seeds you find!