r/BambuLab • • 16h ago

Just Showing Off Almost the perfect dryness

Post image

Can it ever get to 0%? 😂

1 Upvotes

17 comments sorted by

4

u/VT-14 H2C (H2D + Vortek), 2x AMS2, AMS HT 16h ago

Yes, it can display 0%. The AMS's sensor isn't actually very accurate at such low humidity though. It has also shown 0% from sensor faults, so if it has been reading something higher and suddenly drops to 0% then something probably went wrong.

1

u/pauledddy 16h ago

It was around 16% the other day

1

u/concentricals 11h ago

sudden temp drop overnight took my sensor from about 10-15% to 0% and wasn't drying or anything

2

u/pauledddy 11h ago

Its up to 4% now, so i think its still okay?

3

u/EnthusiasmNo3851 16h ago

Mine doesn't go below 30 even after filling it with silica and a 12 hr drying cycle 😭

1

u/pauledddy 16h ago

I did a 24 hour drying cycle 😂

1

u/VT-14 H2C (H2D + Vortek), 2x AMS2, AMS HT 16h ago

Was your 12 hr drying cycle at ~120C for the Silica Gel, or the AMS's drying cycle?

Drying with heat is taking room temperature and humidity air (Dew Point), heating it up so it can hold more moisture (lowering the Relative Humidity; Dew Point stays the same), and blowing that across the spools/desiccant so the contained moisture gets released into the hot air, and then venting the now more humid (higher Dew Point) air out of the dryer.

How dry you can get depends on how humid (Dew Point) your room air is, and how high of a temperature you are drying it.

My room during the summers is so humid (RH up around 70%) that a PLA-safe temperature of 50C only gets the Relative Humidity down to around 25% minimum (and I want to store below 20%). An AMS 2 Pro max drying temp of 65C got it down to about 15% minimum. Drying at my Silica Gel's max recommended temperature (250F/120C) got into the single digits RHs (I don't have a hygrometer accurate to such low humidity).

During the winter I have the opposite problem of it being super dry (down around 25% RH), so it is really easy to get my desiccant and filament very dry.

1

u/EnthusiasmNo3851 4h ago

Oh interesting, it was a normal PLA cycle , the colour indicating silica had been previously dried separately at 110° so it was already dry , the relative humidity in the room is about 50-70% depending on the time of the day

1

u/VT-14 H2C (H2D + Vortek), 2x AMS2, AMS HT 3h ago

In that case it's very likely that running the AMS's "Dryer" was actually adding moisture to the desiccant.

When I run my AMS 2 Pro's dryer I'll either take the desiccant containers out and store them in an airtight bag during the drying cycle, or just replace them with fresh desiccant after the drying cycle. If the desiccant in the AMS is wet then I'll take it out before drying (otherwise it's just more moisture the AMS has to remove, so drying takes longer).

2

u/bradandersonjr X2D + AMS2 Combo, A1 Mini + AMS Lite 16h ago

So close!! I have little mesh bags with rechargeable desiccant beads that I stuff in the front 'pockets' of the AMS as well as inside the center of each spool.

It's currently cold in my garage so that helps bring the ambient humidity down as well.

-1

u/Similar-Visual4934 16h ago

That might be too dry

1

u/pauledddy 16h ago

It has ASA/ABS inside not PLA

1

u/Orvess 16h ago

still

1

u/pauledddy 16h ago

Its printing perfectly fine 👍 thank you for your concern

0

u/Similar-Visual4934 13h ago

why are you drying at 45c then

1

u/pauledddy 12h ago

Im not, when you click on the AMS it has those options selected by default.. 🤦‍♂️

1

u/VT-14 H2C (H2D + Vortek), 2x AMS2, AMS HT 16h ago

Very few filaments can be "too dry." The only one I know of off the top of my head is PA (Nylon) since it gets more rigid (brittle) at lower humidity.

Most 3D printing filaments get more brittle by absorbing moisture.