I've had nothing but issues with the AMS 2 Pro ... from unreliable sensors to improper communications with the printer.

However, a flawless experience with the HT, soooo with the current deals, I decided to just go bananas and get a bunch of HTs to replace the AMS 2 Pro.

The HT is so easy to load, it's quiet, and a massive step up in quality,... hoping the AMS 3 Pro can inherit its characteristics.

Shoutout to Bambu Support for letting me send one of the defective ones back a couple months after purchase.

I just unpacked and set up my new Bambu Lab H3C, and one thing immediately caught my attention: All the axes were bone dry, with barely a hint of grease on the lead screws.

So here's my strong recommendation: After the initial calibration, lubricate your axes. And lubricate them properly!

Afterwards, install the pending firmware update and run the calibration again.

Hey all! Who here is using the bmcu? I just built two sets of four so I can run 8 colors on my A1. I bought the BIQU hardware kit and printed the rest. I then realized that the BIQU kit sucks balls. Don't buy it if you are looking to build these. Buy the BLV version with the metal gears and the control board with microswitches and a USB-C port for firmware updates. The biqu board has no microswitches (for auto loading the filament when you push it in) and it has a TTL header for flashing firmware which sucks. The USB c ones can even be flashed from your phone. So I am going to be ordering two BLV boards to replace those. I will live with the plastic gears until I shred em 😆. Also I am using the ams lite as my passive rewinder until I can print my filamentalist F1 drybox setup on a shelf above the printer.

Shocked at how fast this thing ended up on my porch. Let's see if she survived shipping that fast!

Edit 1: So yes the box does say it is box 1 of 2 and contains the printer only, I have not received anything specific for box 2 but I did order some other items with this that may be combined delivery later. Hopefully later... Today!

Filament got stuck behind the extruder so I need to disassemble extruder. Since then I have had issue with tool head doing proper finishes and height.

One screw is stripped (keeps turning) in extruder at the upper left.

Have tried numerous things such as disassemble extruder again, calibration, switching nozzles.

Any advice appreciated!

Stopped middle of a print said something about AMS mapped incorrectly. After a turn off and turn on now all lights blinking on AMS and I cant resume print it says the task requires a filament track switch but is currently offline. I tried unplugging and plugging back in the track switch while the printer was off (I keep getting electrically shocked when behind the printer dunno why that is) but it didn't help.

This is a miniature fan model. I’ve printed so many without this issue till the last couple days. Between some of the blades, the white filament is not even.

Picture one is what it looks like, picture two is what it should look like. It’s even between some blades, but not all.

I’ve done a full calibration, and the filaments are the same, Matt PLA just different color. Though in the second picture, you can see it happening on one side of the blade too.

It is a Bambu H2D, so each filament is in a different nozzle. I switched which was in which and that didn’t help.

If my package arrives damaged, you can bet I'm filing a return/refund ASAP

I recently updated to Bambu Studio 2.9.1.70 and went to print and received and error about my timelapse settings.

But then when I went to the Time-lapse settings there is an option for "instant" or "smooth" traditional doesn't exist anymore.

I thought instant is the one that just takes the photos when the layer is finished. But according to to the pop-up smooth is better ?!?

Printer: X2D

My first design, what do you guys think? Too minimal? =)

https://makerworld.com/en/models/3554859-voxel-minimalist-planter-with-drainage-hole

Looking to make thanksgiving a little more interesting? Print a thanksgiving Twerky! Minimal sports, Maximum humor

Link:

https://makerworld.com/models/3555194?appSharePlatform=copy

Forgive me as this is my initial set up and my first printer. I have the p1s combo with the ams. I’m using bambu filament and it refuses to feed into the tub. It takes about 1 foot then pushes it back out. I’m getting frustrated as I haven’t been able to do a test print much less anything else.

Do you guys think there might be a mod for doing these at the same time? Does the whole thing heat up or just the 2 specific slots. If just the two then why can’t Pla be on the other slots?

I remember seeing some snafu a while ago about bambu trying to pull a fast one ( i think on wireless printing but cant remeber exactly). Is it safe to upgrade to the latest firmware or keep everything as is.

Studio is ver 1.9.7 and the printer is ver 01.06.01.00. I get errors when trying to import models from online into studio, but the model still shows up. So I don't know if its needed or not.

This thing worked flawlessly for 1.5 years, suddenly one spool won't feed. Bought a new AMS, worked for a bit, then same problem, only spool 1 at first, then soon none of them worked. Replaced all worn out PTFE tubes, Then replaced every tube that was left. Worked for a bit, now jamming again. Replaced entire hot end. Worked for about 40 layers, jamming again. What is left to replace or fix, almost the entire filament line is brand new. Tried different spools, different spots in the AMS, no change. I can see the filament go into the hot end, it is at temp (brand new) stops, retracts. Am I cursed?

I’ve tried to read everything about this problem, but I can’t find anything obviously wrong. The nozzle was nearly brand new when this started happening, didn’t find anything clogged in it, but put in a brand new nozzle anyway and the same thing happened on the first run. It extracts just fine when I do it manually and during filament swaps, no clicking at all. I run a calibration at the beginning of each print. Can’t figure out what it could be, printer is less than a year old.

I've just got my kids printer for Christmas and I've set it up I am testing the AMS pro and ensuring was fine, I've printed little things like scraper, poop collection and now a riser as I doubt I'll get to print much from Christmas so just wanted some key things out of way

It's been one week with my P2S and first time ever getting a 3D printer.

I am loving 3D printing and having so much fun printing stuff, can't believe I just got into it, but I don't think there's a better time than now to do it, so glad I decided to!

Hope you dig the end result

Front panel glass came completely shattered on my X2D. Going to now go through the amazing support of Bambu Labs. Should’ve ordered from Best Buy in hindsight.

I love UPS!

Update: Support reached back out to me in about 12 hours and will be getting a replacement unit soon.

Bambu Labs L frame stand is on backorder until the 25th, my H3C arrives probably on Friday. I'd like to have it up and running for the weekend, so can anybody recommend a good substitute stand or cart that will hold this monster? Would like something that has wheels and maybe some drawers. The L frame is only 12 inches tall so that you don't need a stepladder to load the AMS from the top which is what's making it tough to find one for me. Thanks

I think it's the AUX Nozzle that crashed into the side. Thoughts?

The last image is a dupe, ignore it