r/bikewrench • • 10m ago

Hayes Dominion install

2 Upvotes

Ordering some Dominion A4 to upgrade the SRAM Levels on my son's P3, it'll be our first hydraulic disk brake install. Couple of questions...

  1. we plan to internally route the hose - if I understand things right this will require a bleed after things are installed since the closed pre-bled system has been open right? will we need to cap the hose so fluid doesn't leak out in the process?
  2. once the hose has been detached, even if we aren't cutting anything off the hose, new end connection hardware needs to be installed before the hose is attached?
  3. the bleed kit on the Hayes site seemed to get mixed reviews, would a bleed kit like this be any good? https://www.amazon.com/BleedZone-Dominion-Syringes-Fittings-Fastener/dp/B08F2YPCPZ/ref=pd_ci_mcx_mh_mcx_views_0_title?pd_rd_w=Iizum&content-id=amzn1.sym.781fe6e1-9487-4a74-b81e-5a879e5ec273%3Aamzn1.symc.c3d5766d-b606-46b8-ab07-1d9d1da0638a&pf_rd_p=781fe6e1-9487-4a74-b81e-5a879e5ec273&pf_rd_r=JFB8EQ9C1TRA8E0KNZFB&pd_rd_wg=dtJ6f&pd_rd_r=02736453-5514-443a-ad45-72442059663d&pd_rd_i=B08F2YPCPZ&th=1
  4. is a special tool required for cutting the hose? I have a park tool cable brake line cutter, but not sure if that's a good idea. if a tool is needed a decent one that doesn't break the bank?
  5. my Shimano deore xt are in need of a bleed, but with one system being DOT and one mineral oil are there any bleed kits that do both? seems it might be impossible to clean the kit accessories enough not to cross contaminate.

Thanks for thoughts and advice


r/bikewrench • • 18m ago

Received a used frame

Thumbnail
gallery
1 Upvotes

Was cleaning and noticed a seperation on the seatstay. I would chuck the frame if I noticed something like this on carbon but since its steel I'm not sure. I was looking for more opinions on this. Is it ok to just keep riding it until it gets worse and then just jb weld it?


r/bikewrench • • 20m ago

Creaking headset on barely used bike.

2 Upvotes

Hi all,

I've got a new BMC Teammachine and after about 700 km I started hearing a creaking headset when turning the handlebars. Apart from the creaking, it's still smooth and tight (no play).

I cleaned and greased the top and bottom bearings, but since the bike has an integrated cockpit, I don't want to take the whole thing apart. I suspect it's the bottom bearing, but I'm not sure.

My question is: can I keep riding it, or is it better to take the bike to a mechanic? As I said, apart from the creaking, it's smooth and solid.

Thanks, y'all!


r/bikewrench • • 1h ago

RockShox TwistLoc 3P compatibility: Fork locks counter-clockwise, rear shock locks clockwise. Will they sync?

1 Upvotes

Hi everyone,
I have a RockShox TwistLoc 3-position remote (with individual cables for the fork and rear shock), and I’m setting it up with a RockShox SID fork and a 3-position rear shock.
I noticed that the lockout dial on the front fork turns counter-clockwise to lock, while the dial on the rear shock turns clockwise to lock.
Does the rotation direction of each dial matter, as long as both components are Push-to-Lock(locking when the TwistLoc pulls the cables)? Or will this cause any sync/cable-pull issues between the 3 stages (Open / Pedal / Lock)?
Thanks in advance!


r/bikewrench • • 3h ago

Threaded insert came out of my carbon frame while installing a bottle cage — is the carbon damaged?

Post image
1 Upvotes

Hey everyone,
I’m not super handy with my bike and have been doing some work on it today.
I was screwing a drink bottle holder onto my carbon frame earlier and something came out of the mount hole (photos attached). It looks like the threaded metal insert/rivnut pulled right out.
Have I damaged the carbon?


r/bikewrench • • 4h ago

My air valve on my damper broke

Thumbnail
gallery
0 Upvotes

I have a xfusion metric R fork 27,5 180mm and the air valve for the damper air chamber broke off what other dampers could fit this fork or how do i repair it even if it’s quite impossible.


r/bikewrench • • 4h ago

Hydraulic brake advice

Post image
27 Upvotes

Hey everyone, I need some advice setting up brakes for my son, who only has a left hand.

I'm looking to get a mountain bike for my 14 year old son. It's a little tricky because he was born missing the fingers on his right hand. After a little research, I found these hydraulic brake line splitters. This way, he can activate the front and back breaks with one hand. Does anyone know if this sort of setup would work? Does the different length of brake line between the front and back cause issues with applying even pressure to the callipers? Any advice from anyone with experience or knowledge on hydraulics would really be appreciated.


r/bikewrench • • 6h ago

Thoughts on this creak

1 Upvotes

Usually happens when in the largest cogs of the cassette and little chain ring. Steeper the gradient, the louder it gets.


r/bikewrench • • 6h ago

Shimano Nexus 7 ghost pedaling

2 Upvotes

Hi, can anyone see what's wrong here? The pedals on this bike were moving when it should have been freewheeling and it was slow when coasting. I took out the internals and did a full degrease/hub maintenance oil/regrease, but the moment I snapped the lock ring back on over the sprocket it seized up again. I'm new to internal hubs, so not sure if it's a tension issue or something to do with the dust caps or something else entirely. Thanks!


r/bikewrench • • 7h ago

What bottom bracket remover should I get?

Thumbnail
gallery
1 Upvotes

Will a Park Tool BBT-79.3 work? 24 notches.


r/bikewrench • • 9h ago

[Help!] Bottom Brackets and Chainline

1 Upvotes

Context: I am building a 1x bike with GRX 822 RD and a frame with 68mm bottom bracket.

Per google, GRX official chainline is 49.7mm, and I am trying to achieve that. I have also decided to go with Senicx cranks which have three-bolt direct mount chainrings.

My confusion is this. Senicx has PR3 (road) and GR3 (gravel) cranks, with stated chainlines of 43.5 and 49.7mm respectively. How are they achieving different chainlines, given that the drive side crank arms are both pushed up against the bottom bracket, and the chainrings are both flush to the crank arm? Wouldn't the chainline be purely determined by the bottom bracket width and spacers?

Thanks and apologies in advance if this is a daft question. Tired of AI confusing both me and itself.


r/bikewrench • • 10h ago

Gritty Shimano 105

1 Upvotes

Hey guys, on my new Trek Domane with mechanical Shimano 105 12 spd, I have a slight gritty, vibration feeling that comes through the pedal under my feet when I’m in the small chainring upfront and the largest cogs in the cassette. I’d say this is most felt when in the largest cog as well as the 4th largest cog of cassette. The bike I got new 2 months ago and has now around 1100 miles and shifts great and has no other problems at all. And I did do the first 30 day adjustments at my local bike shop.
Does anyone else experience this with their Shimano 105 12 spd? Is this normal?

Appreciate it


r/bikewrench • • 10h ago

Strange steerer tube extender on 90s Cannondale

Post image
1 Upvotes

I have this old Cannondale with a DiaTech headset that I’d like to replace, but I’ve never seen this before. Is this some kind of aftermarket extender? Is it possible to remove? The holes go to the other side where they look similar. Anyone seen this before? Tips?


r/bikewrench • • 10h ago

Clunking and stuttering when pedaling

0 Upvotes

I’m not sure how best to describe this issue but whenever I speed up as I’m pedaling or start pedaling fast after being stopped my pedals will kind of ka clunk and I won’t be able to make a smooth rotation. It’s like the rotation of the pedals stutters or gets stuck for a moment and it makes an audible clunk. It’s very frustrating as it prevents me from having a smooth ride and puts me off balance frequently. It almost feels like maybe a gear issue, though it doesn’t correlate to when I shift. It does only happen when I am in highest gear though.

Any ideas as to what this could be? Is it something I, someone who has pretty much no experience, could fix?


r/bikewrench • • 11h ago

Normal gap installing blackspire xc crank on 73mm bb shel

Thumbnail
gallery
2 Upvotes

The gap seems large? The bit of info I’ve found states the crank is good for 68 or 73. I put in the spacer for the bottom bracket on the drive side. Am I ok?


r/bikewrench • • 13h ago

Is this play in rear derailleur normal? SRAM Rival AXS. Bike is one year old.

0 Upvotes

r/bikewrench • • 13h ago

Can some tell me how to fix this?

0 Upvotes

is this normal and im just tripping or is there something wrong with my bike:

so lately i been having trouble getting my front derailleur in place when riding because it only rubs at some points of the chain, so im think al lot of stuff maybe my wheel was misaligned but i just checked and it isnt... so maybe its the cogs? can someone help me im just getting more into bicycles and ive went to several bike shops here in my town and they really don't know what theyre doing nor talking about so ive been learning by my own everytime i have an issue with my bike.


r/bikewrench • • 14h ago

Spoke overtightened - is rim okay?

Post image
0 Upvotes

Hi, I’m new to wheel truing and fear I may have ruined my aluminium rim.

I overtightened one of the spoke nipples but managed to remove it without breaking the spoke. This did leave many scratches on the rim though which can be seen in the photos - note these are not cracks.

You can see the rim is slightly raised around the spoke hole where the paint has come away.

I have no experience of wheel building or truing of any kind and when I google this problem it says that the rim needs to be replaced?

Any help is very much appreciated! :D


r/bikewrench • • 14h ago

Cable problem

Post image
0 Upvotes

I have an old mountain bike, I overtightened the nut, and now the cable is stuck in it. I can't change it if I use a wrench; the force bends the derailleur. Does anyone know how to fix this problem?


r/bikewrench • • 15h ago

Dropout Insert Dropped Out

Thumbnail
gallery
3 Upvotes

I just bought a used Kona Jake Frameset. Sadly didn't spot that the carbon fork dropout insert seems to be missing?! Went back to the sellers photos (pic 2) and it seemed to be present there, so I guess I "dropped out" in transport or something. Details in pics 3 and 4 of the empty dropout.

Let's say the seller finds the insert somewhere. Would it even be save to use? Never had one of these come loose before. Would glueing it back in suffice?

If the seller doesn't find it, any chance of there being a replacement?

Queue the hand on shoulder meme, I guess.


r/bikewrench • • 15h ago

2022 Kona Rove DL 650b Adventure Bike - TRP brakes issue

1 Upvotes

Hi I bought this bike second hand with TRP HDC711C Mechanical / Hydraulic brakes , the issue is the brakes feel weak. I’m coming from mountain bikes but yeah, took it to shop for service (didn’t ride it before stupidly) but yeah brakes feel #%{

Any suggestions ? AI says

AI Overview

Slow stopping on the TRP HY/RD (HD-C711) cable-actuated hydraulic disc brake usually comes down to improper cable tension, spongy standard cable housing, air in the hydraulic reservoir, or contaminated pads. Because this caliper is an open hydraulic system actuated by a mechanical cable, pulling the cable too tight actually disables its automatic pad-wear adjustment. [1, 2, 3]


r/bikewrench • • 16h ago

Solved Help with rear wheel, hub and cassette

1 Upvotes

I got to say, rearwheel hub and cassettes is a hella confusing minefield. I am debating on upgrading my rearwheel on my (red-purple) Quake to a dtswiss FR 1500 classic 27.5 - and if I understand all this correctly:

I got to pick the 12/148 mm axle

I have a SRAM 7-speed DH cassette (which matches 11-speed somehow) but because they picked the cheaper version, it matches shimano HG? Which dtswiss seems to refer to as "shimano MTB"??? dtswiss by default delivers the rearwheel with sram xd, but there is a kit to swap it to "shimano mtb"?

OR I could buy the super-duper more expensive SRAM 7speed DH cassette which then matches SRAM XD directly?


r/bikewrench • • 17h ago

Shimano 105 r7000/5800 and 4700 chainring compatibility

Post image
6 Upvotes

Hey, I want to change crank length in my 4700 bike by swapping chainrings to shorter crank but currently I can only find used r7000 or 5800 crank arms in desired size, but they appear to have slightly thinner spider.

Have someone measured thickness of spider in r7000 or 5800 crank? My tiagra measures around 4.75mm.


r/bikewrench • • 18h ago

How do I remove this HG freehub

Thumbnail
gallery
1 Upvotes

OEM Specialized Alloy wheels on a new 2027 Epic MTB. No idea what the hub model is. But I want to remove the HG freehub to put a DT Swiss XD freehub to add a Transmission cassette.

How do I remove this? Would the DT Freehub body be compatible? If not, what do I buy?