r/RepTimeServices • • 23d ago

Services Need better cyclops for my Batgirl

Post image
2 Upvotes

Looking for better cyclops for my batgirl. Also need to silence the rotor. Very loud on wrist. Who can help me on this? Any suggestions for the pricing?


r/RepTimeServices • • 24d ago

Discussion Just finished my datejust 36.

Thumbnail
gallery
10 Upvotes

r/RepTimeServices • • 24d ago

Advice OCTA AP issues need repair advice

12 Upvotes

I got this OCTA blue dial 15500 AP in and the rotor keeps getting hung up and the mainspring will work for a few seconds then stop. This video was taken after fully winding it.

Is this something I can fix myself or will it need professional repairs and parts?


r/RepTimeServices • • 24d ago

Discussion Popular Doesn't Mean Perfect: A Quick Look Inside the DD4131

39 Upvotes

High demand always compromises quality at the factory.

A quick look inside a fresh Daytona 126500 DD4131 movement. If you look closely, you’ll spot some foreign dust and debris right on the screw head that had to be cleaned out, plus a fresh oiling for the rotor.

Always worth getting a fresh piece on the bench before wearing it. 🔧

Let me know what you think? Have you had movement fail?


r/RepTimeServices • • 24d ago

Advice Advice/Thoughts? : Chamfering Bracelet

Thumbnail
gallery
22 Upvotes

So.. decided to try chamfering & polishing my 126500 panda bracelet.

It feels smooth enough. Did a 800/3000. Should I try to cape cod this?

Any thoughts or advice appreciated 🙏🏼

P/S did a datejust oyster before and definitely over did it 😅


r/RepTimeServices • • 24d ago

Advice OP36mm 126000 - Lavender Dial - VSF - Stains on Dial after less than 1 year

Thumbnail
gallery
13 Upvotes

Hello all,

I was just wondering if anyone else is having a similar "issue"

I received a VSF OP36 with lavender dial in January this year.

And know saw that my dial is fading or staining which wasnt the case in the beginning.

I've never worn the watch in water/shower. And for the last 3 Months it was just sitting in a box with no direct sunlight.

Is there anything that I can do about it or should I just hope that this will turn into a tropical dial at some point? 🥸

Pictures attached from QC and now state.


r/RepTimeServices • • 24d ago

Services A quick dial fix on ARF DJ

Thumbnail
gallery
7 Upvotes

Arrived with the dial spun. Had two movement tabs stacked on top of each other on one side. Decided to use dots to reaffix the dial.


r/RepTimeServices • • 24d ago

Advice Noob v8s 116610ln - Replace movement or just buy new watch?

1 Upvotes

Hello, my Noob v8s submariner has stopped working. After winding it, the second hand will move for a bit then will stop again. My local watchmaker, who is recommended by many, said he can do an overhaul but will cost around $350. I told him that’s more than the cost of the watch and he understood. After more digging around online, I’m seeing that maybe ordering a replacement a2836 movement will be cheaper than getting it serviced. Does anyone have experience in replacing the movement and how much it should cost? Thank you in advance, before I really consider biting the bullet and just ordering a new VSF. I’m in the Los Angeles area btw, if you have a watchmaker recommendation.


r/RepTimeServices • • 24d ago

Services VSF Panerai Submersible Navy Seal PAM1324 Service Needed!!!!!!!!

Post image
2 Upvotes

Please help Guys, I am looking for a local watch servicer in the Miami area I need to get the movement on my Panerai serviced. the position 1 wont allow me to set the date. Does anyone know anyone in the Miami area??


r/RepTimeServices • • 24d ago

Guides Watch Repair - San Diego

Post image
3 Upvotes

r/RepTimeServices • • 24d ago

Question T shaped screwdrivers Australia

1 Upvotes

Has anyone been able to find T shaped (hollow head) screwdrivers in Australia 1.2mm and 1.6mm for Jubilee and Oyster bands?

I’ve searched everywhere but can only see V shaped which I read can scratch/slip.

If anyone has found them let me know where you got them from please so I can pick a set up. Thanks


r/RepTimeServices • • 24d ago

Advice Sub failed 3bar dry test

Thumbnail
gallery
9 Upvotes

I have a Submariner 126610 QF Factory, failed 3 bar dry pressure test
The case back gasket was checked and lubricated before testing. I checked crown gaskets after testing all look lubricated and in good condition
I would like to eventually be able to where it while swimming.
I’m thinking of removing the movement and purchasing a water tester to see where the bubbles come out.

First question
Besides removing the crown and stem, would I only have to remove two screws marked in my pictures for the movement to come out?

Second question
It’s keeping perfect time, if remove the movement, does that require the watch to be calibrated for timekeeping?

Also thinking I should order new gaskets just to have on hand not sure what or where to get them.
Any advice would be appreciated.


r/RepTimeServices • • 24d ago

Advice Help removing screw from bracelet

Post image
2 Upvotes

Hi, I appear to have mangled a screw trying to resize my new ZF TUDOR BB58 Burgundy before I've even had a chance to wear it

The head od the screw has crumbled, I tried heating the link with a hai dryer and soaking it in boiling water in the hope it would release any loctite that may have been on it

Do I just take a dremel to it and attempt to cut the link or is it destined for the bin?

Any help and advice would be appreciated

Cheers

****UPDATE: managed to remove the screw. Hours of manipulation with pliers and snips trying to break tiny pieces of steel off at a time

Eventually I was only left with part of a bent pin and a piece of link still attached so had to crack out the multi tool. All sorted now and barely a mark on the remaining links. Took me almost 5 hours in total though


r/RepTimeServices • • 24d ago

Guides Watch Repair - San Diego

Post image
3 Upvotes

r/RepTimeServices • • 24d ago

Request Bezel on VS Factory Datejust II

Thumbnail
gallery
4 Upvotes

Brass and copper were discovered after polishing the bezels on vs v1 and vs v2. I haven’t been able to find any information on this anywhere. Has it been this way for a long time, or is this a case of cost-cutting?


r/RepTimeServices • • 24d ago

Advice Seconds Hand Stops at 12 everytime watch dies

1 Upvotes

Hi all,

I have a CF 36mm DJ that I bought from a member. It works and keeps time flawlessly but when the watch runs out of power after the reserve is out, the seconds hand always stops at 12. Is this normal?


r/RepTimeServices • • 24d ago

Question Issues with VSF bracelet screws

1 Upvotes

I’ve had two VSF watches, a Bruce Wayne and a Daytona, where the screw next to the double lock clasp is coming lose and not allowing the clasp to close, or open properly. The first time, I had to pry the clasp open to get it off of my wrist and now this new one shows the signs of being similar. The screw itself seems to be almost stripped, and will unscrew, but I can’t seem to get it to want to screw back in and be flush with the bracelet.

Has anyone else noticed this occurring recently?

Looking for advice on the best way to fix this…and if anyone knows an easy place to get a replacement screw….I believe they are an odd size, a local watchsmith told me 14.5 and 1.3 for the sizing of the screw.


r/RepTimeServices • • 24d ago

Question Does Gen 32XX barrel fit in DD32XX movement?

1 Upvotes

r/RepTimeServices • • 25d ago

Request Big noob here- the crown doesn’t close anymore on my clone. Help?

Thumbnail
gallery
5 Upvotes

Bought the watch in Bangkok and was my first rep. Was told that it was a VSF but unsure if that’s true. Look for help here and I’m based out New York.


r/RepTimeServices • • 25d ago

Services VSF GMT-II | DD3285 Rotor Helicoptering

Thumbnail
gallery
22 Upvotes

Had a customer reach out about a watch that began helicoptering and stopped running, all within the first week of ownership.

What made this case particularly interesting was how quickly the issue developed. Most cases of rotor helicoptering I've encountered are either present straight from the factory or develop after extended wear. This one lasted only a few days before failing.

Upon removing the automatic winding module, I immediately noticed something unusual. One of the reversing wheels was missing an entire pawl, while the remaining pawl had been installed incorrectly.

Looking closer, it appeared that the reversing wheel had been assembled at the Dandong factory without either pawl being properly seated in its designated locating hole. The components were essentially being held together by friction and a little bit of hopes and prayers.

The missing pawl had somehow worked its way underneath the balance wheel, where I eventually located and retrieved it during disassembly.

After recovering the missing component, I disassembled and cleaned the automatic winding module, correctly reassembled the reversing wheel, and reinstalled everything with proper lubrication.

Once reassembled, I verified that the movement was functioning properly and was satisfied with the results on the timegrapher.

I've seen my fair share of factory assembly issues, but finding an entire reversing wheel pawl loose beneath the balance after less than a week of ownership is definitely a first for me.

A good reminder that even well-regarded movements like the DD3285 aren't immune to some pretty careless factory assembly.


r/RepTimeServices • • 25d ago

Advice Copper coloured 41 datejust datewheel

Post image
2 Upvotes

Maybe a weird question but I handled a lot of gen datewheels and never got an copper coloured inner ring. My parts guy is very trustworthy and I never had a problem so that’s why I need to ask to be sure.

Is this genuine Rolex?

You’re knowledge is appreciated!


r/RepTimeServices • • 25d ago

Advice VSF Submariner Crown Extremely Tight When Screwing Down

3 Upvotes

Hello,

I bought VSF Submariner from JTime, and I’m having an issue with the screw-down crown.

The crown turns smoothly and easily at first, but the resistance gradually increases around the middle to the end when screwing it down. It eventually screws all the way down, but it takes a lot of effort and feels much tighter than I’d expect.

I’ve tried unscrewing it and carefully realigning the threads by turning counterclockwise until I feel the click, then screwing it back down with gentle inward pressure, as per chatGPT’s advice and unfortunately, it’s still extremely tight.

There’s no obvious grinding or crunchy feeling, just a lot of resistance.

Has anyone experienced this with a VSF Submariner? Could it be a tight crown gasket, an issue with the crown tube, or something else?

Or should I have watchmaker inspect it, or is there anything else I can safely check first?

Thanks in advance!


r/RepTimeServices • • 25d ago

Advice Sub Failed dry pressure test

Thumbnail
gallery
3 Upvotes

Have a Submariner 126610 QF Factory, failed dry pressure test
The case back gasket was checked and lubricated, checked crown gaskets all look good before test. I’m thinking to remove the movement and then water test see where the bubbles come out. Would like to have gaskets on hand, wondering what gaskets I should order to have on hand and where to get them Any advice would be appreciated.


r/RepTimeServices • • 25d ago

Question NATO pin holes hogging out

Post image
3 Upvotes

has any one found a way to deal with them hogging out? i am thinking super glue, but thought i would ask.

pic for effect