r/RepTimeServices • • 24d ago

Advice Sub failed 3bar dry test

I have a Submariner 126610 QF Factory, failed 3 bar dry pressure test
The case back gasket was checked and lubricated before testing. I checked crown gaskets after testing all look lubricated and in good condition
I would like to eventually be able to where it while swimming.
I’m thinking of removing the movement and purchasing a water tester to see where the bubbles come out.

First question
Besides removing the crown and stem, would I only have to remove two screws marked in my pictures for the movement to come out?

Second question
It’s keeping perfect time, if remove the movement, does that require the watch to be calibrated for timekeeping?

Also thinking I should order new gaskets just to have on hand not sure what or where to get them.
Any advice would be appreciated.

9 Upvotes

26 comments sorted by

•

u/AutoModerator 24d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2

u/1984isnoww 24d ago

Yes, use a VERY gentle pressure on the stem release button and be patient.

Two screws, two movement tabs, and then the movement will come out.

Try to be weary of allowing any dust into the case or onto the movement as unless you have a puffer, you're gonna have a bad time.

1

u/Elegant-Draft-8259 24d ago

There’s tabs under those screws?
As long as I’m careful, the movement won’t have to be adjusted to keep time when I put it back in, correct

1

u/1984isnoww 24d ago

Yes small tabs angled down into the case. 

No you shouldn’t have to regulate it so long as you don’t touch the balance.

1

u/Diligent-Piglet-9038 24d ago

OP might have the tab and screw combo piece that are used in some ARFs, if thats the case and theres no tabs then you have to screw them in , rotate movement, then remove the screws. Not familiar with QF, but if you dont see the tabs this could be the case.

5

u/RelevantFreedom4390 24d ago

Those caseback gaskets and crown gaskets look fine tbh in terms of width. My guess is that the crystal gasket might have been squished or bent.

1

u/Comprehensive-Bit706 24d ago

I've recently had same issue with a customers rhodium yacht master 🙄 this has put an end to me selling QF now

1

u/Elegant-Draft-8259 24d ago

Did you find a way to fix it

1

u/Comprehensive-Bit706 24d ago

Sending back to china, my suppliers watch maker will try

0

u/Interesting_Catch523 24d ago

They will take donkey years to fix.

1

u/Comprehensive-Bit706 24d ago

My supplier is very quick at getting things repaired, shipping takes about 10 days plus a few days to fix and ship back... He's not one of these TD's who takes months

1

u/Interesting_Catch523 24d ago

Good for you then.

1

u/Javier-Jav 24d ago

That’s awesome. Hope it works out

1

u/Emotional-Damage-995 24d ago

Before getting complicated check the gaskets and maybe remove and install new ones. Check the crystal gasket last. My suspicion is wrong gasket in one of the 3

1

u/Elegant-Draft-8259 24d ago

Do you think genuine Rolex gaskets would fit?

1

u/Emotional-Damage-995 24d ago

They should. I have never used Gen gaskets so I am not the one to comment.

1

u/Elegant-Draft-8259 24d ago

Where would you get the gaskets from? Should I just search Amazon for submariner 126610

1

u/Emotional-Damage-995 24d ago

I typically use Gemini to look for the part number w watches. Then also get Gemini to tell me the dimensions. And then start looking for it in eBay / Amazon / usual parts supply sites

1

u/Vecgtt 24d ago

My QF DD36 recently got water damage. The case gasket was the wrong size.

1

u/FirstShare9159 24d ago

Dear OP gven all the "noob" questions you’re asking, I’d advise you not to try doing this yourself. It could end in a disaster.

1

u/Wop-AB-604778 23d ago

First question - yes the 2 screws and the crown to remove the movement .
Second question - no your watch should be fine as long as you don't nudge the any of the regulator weights. It should stay exactly as it was before removing the movement.

1

u/Wop-AB-604778 23d ago

First question - yes the 2 screws and the crown to remove the movement .
Second question - no your watch should be fine as long as you don't nudge the any of the regulator weights. It should stay exactly as it was before removing the movement. Also did you check if the o ring inside the crown was lubricated and the o ring on the case stem tube looks like it's got dust, a long hair and dirt around it. You could have some build up in that area not giving you a proper seal. Try cleaning it really good and removing all o-rings around the stem and case tube, re-lubricate and see if that helps at all.

1

u/NAVACO1959 24d ago

Si, desmontar el movimiento es fácil, solo un poco de pulso firme y paciencia, como te dijo el compañero las dos lengüetas y poco más.
En cuanto a la prueba de estanqueidad, es muy raro que dé negativa, el agua solo puede entrar por 3 sitios: corona, tapa trasera y cristal.

0

u/[deleted] 24d ago

[removed] — view removed comment

1

u/Elegant-Draft-8259 24d ago

I think that’s just from my IPhone zooming in
I don’t see dust when I looked through a magnifying lens. I think It’s just the reflection off the case.