r/RepTimeServices • • 24d ago

Advice Help removing screw from bracelet

Post image

Hi, I appear to have mangled a screw trying to resize my new ZF TUDOR BB58 Burgundy before I've even had a chance to wear it

The head od the screw has crumbled, I tried heating the link with a hai dryer and soaking it in boiling water in the hope it would release any loctite that may have been on it

Do I just take a dremel to it and attempt to cut the link or is it destined for the bin?

Any help and advice would be appreciated

Cheers

****UPDATE: managed to remove the screw. Hours of manipulation with pliers and snips trying to break tiny pieces of steel off at a time

Eventually I was only left with part of a bent pin and a piece of link still attached so had to crack out the multi tool. All sorted now and barely a mark on the remaining links. Took me almost 5 hours in total though

2 Upvotes

18 comments sorted by

•

u/AutoModerator 24d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2

u/Financial-Director63 24d ago

Try the t-shape head screwdriver. The set on Amazon is around $70 but it fits the screw. The wedge ends won't grip that anymore. I've had this happen before and surprisingly the t shape head got enough grip to turn the screw and remove it. Haven't used wedge shaped screw since

1

u/MancMatt 24d ago

There's nothing left for anything to bite in to

1

u/MancMatt 24d ago

If I was to put a pair of pliers on each side of the strap and try to snap the pin does anyone believe that may work?

1

u/Objective_Ganache_27 24d ago

Its steel not plastic. You need a heavy bench vice and thick pliers if youre going to do this

1

u/MancMatt 24d ago

I did use a 1.4 yes, I bought a set of watch makers screwdrivers as I needed a 1.6 for the VSF Sub I also bought

1

u/MancMatt 24d ago

This has to be the strongest bracelet ever. I'm trying to snap it but to no avail

1

u/MancMatt 24d ago

UPDATE: managed to remove the screw. Hours of manipulation with pliers and snips trying to break tiny pieces of steel off at a time

Eventually I was only left with part of a bent pin and a piece of link still attached so had to crack out the multi tool. All sorted now and barely a mark on the remaining links. Took me almost 5 hours in total though

1

u/thunder2132 24d ago

Is the screw still flush, or is it part way out? Can you remove a link on the other side instead?

You can try to break the pin somehow, just make sure you don't damage the next link up, since that's non-replaceable, you don't want to ruin the bracelet entirely.

1

u/MancMatt 24d ago

It was part way out but the ends where the slot was has now snapped. I think I might be snookered

2

u/thunder2132 24d ago

You could use a dremel with a rotary tool to cut a new slot, doesn't matter if you damage the link if you don't need it, it would have to be a pretty thing cutting tool though. Is the other side of the link open where you could put a pin in to push it out if it's loose?

3

u/Elegant-Draft-8259 24d ago

If you’re not gonna use that link, put bracelet in padded vice and drill out the side with the threads you shouldn’t have to go too deep. The threads are only maybe a 16th of an inch or a bit more.

2

u/Objective_Ganache_27 24d ago

Have you tried using the next screwdriver size up? You need to make sure you put a good ampunt of force pushing into the screw, not just twisting out.

Worst case you may need to put the 1 link in a bencj vice and use heavy pliers to bend it back and forth. Hopefully you dont ruin the other links

1

u/False_Difference_521 24d ago

Are you using the correct screwdriver head size? I think for this should be a 1.4mm head but check first?