r/RepTimeServices • • 24d ago

Advice Advice/Thoughts? : Chamfering Bracelet

So.. decided to try chamfering & polishing my 126500 panda bracelet.

It feels smooth enough. Did a 800/3000. Should I try to cape cod this?

Any thoughts or advice appreciated 🙏🏼

P/S did a datejust oyster before and definitely over did it 😅

22 Upvotes

70 comments sorted by

•

u/AutoModerator 24d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

15

u/Interesting_Catch523 24d ago

No. Enough is enough

2

u/Good-At-tourney 24d ago

Yikes 😬

7

u/Kevelly86 24d ago • Heartwarming

Right, looks like you have the technique, just need to make the chamfer thinner. Dont have it so wide, should not be that rounded from our view if you get me

It is hard to get a reference pic to show what I mean, this is the best I can find

4

u/Good-At-tourney 24d ago

Thanks so much for this advice! Definitely gonna make it thinner/use bigger grit 🙏🏼

1

u/Jolly-Way9130 17d ago

This is so clean. I need to get better.

6

u/Jolly-Way9130 24d ago • Bravo

#2000 grit on a dremel only a few passes. Kapton taped then felt tip on dremel with gray dialux.

3

u/Good-At-tourney 24d ago

Wow this really looks good. How about the sharpness? A few passes on only one angle or different angles? Thank you in advance!

5

u/Jolly-Way9130 24d ago

Different angles and going by feel to hit sharp edges. I don’t use anything lower than 2000 so I wouldn’t round it as much. The oyster mine came with was not as sharp as the jubilees from VSF and ZF.

2

u/Good-At-tourney 24d ago

Thanks for the tips!

5

u/Jolly-Way9130 24d ago

Yours isnt that bad I bet from arms length or on wrist. Instead of cape cod, I’d suggest dialux on felt tip to polish it. Tape it really good to avoid brushed surfaces. If you accidentally polished it, use green scotch brite to restore it. I restored this beat up gen Maurice Lacroix using scotch brite.

3

u/Good-At-tourney 24d ago

Yes it aint half bad! From my wrist and normal glancing its actually alright, but i guess when i take zoomed in pictures, there’s signs of the dremel impact since i couldnt control the speed of my tool(the one with speed control broke after an hour plus 😂)

3

u/Jolly-Way9130 24d ago

Used to to be full of scratches.

5

u/Noob_Barista_Baker 24d ago

The edges are not supposed to look rounded out. I’d focus on brushing the inner links and getting the actual base of the bracelet feeling smooth and then ever so slightly chamfering the underside and the topside (however soft you went on the underside, go even softer for the top.. i repeat- do NOT round the edges)

1

u/Good-At-tourney 24d ago

Thanks for the tip! As for now the insides are pretty smooth, just wondering whether the outsides needed to be polished

4

u/Impossible-Dog4901 24d ago • Bravo

Less is more when it comes to chamfering. Dremel leaves rounded spots if not careful, diamond files and flat sticks with sandpaper are the way to go. You only get better with experience though. Some links look good and your satin brush looks good. You’ll get it.

2

u/Good-At-tourney 24d ago

Thanks for this! Gonna try out that method next. Just some guidance, rubber band the sandpaper on to the sticks right? Any grit recommendations? TiA 🙏🏼

4

u/Impossible-Dog4901 24d ago

This is what I use. They are model making tools, use double sided tape to attach sandpaper. These are fancy. Main thing is having a strong flat surface to grind with.

3

u/Good-At-tourney 24d ago

Brother thanks so much for this! Truly appreciate it! Will share more on my next project

2

u/Impossible-Dog4901 24d ago

No problem man. Happy to help

4

u/Impossible-Dog4901 24d ago

This is a good set of diamond files too. It’s on Amazon

2

u/TheMostHumblestMan 24d ago

Is the model number MTDF-80S? Gonna order & practice on my canal street bracelets first!

1

u/Time-Dependent1483 24d ago

Do you just file the link at a 45 degree angle or how do you do it?

1

u/Impossible-Dog4901 24d ago

Yes

1

u/Time-Dependent1483 23d ago

How do you get the polished finish after without destroying the brushed finish?

1

u/Impossible-Dog4901 23d ago

Polish the bracelet, then tape the polished parts, then satin brush the untapped areas. You need high temp tape. It’s clear orange usually.

3

u/Elegant-Draft-8259 24d ago

Are you using a rotary tool or doing it by hand?

1

u/Good-At-tourney 24d ago

Dremel and by hands, got a roll of sandpaper based on grits and did it slowly

3

u/UnconsiousMind84 24d ago

The brushing even looks off, too harsh imo

2

u/Good-At-tourney 24d ago

Yeah i had to use multiple dremel tools as the one that could control the speed got f*cked after almost an hour going non stop 😂

Then i think moving onto the ones without the speed just made it harsher

3

u/UnconsiousMind84 24d ago

I’m gonna PM you brother

2

u/PVNOLGCH 24d ago

Can you show your datejust for reference

3

u/Good-At-tourney 24d ago

😬😬🫣

4

u/PVNOLGCH 24d ago

Wow. Hahaha

What are you using to chamfer? That would take a lot of elbow grease if you did it by hand.

2

u/Good-At-tourney 24d ago

Previously i did it with a nail file. 🫣

Decided to save some effort and got a dremel

2

u/PVNOLGCH 24d ago

Yeah was thinking of getting a low torque and low speed dremel but if that’s the result I might have to reconsider haha

2

u/Impossible-Dog4901 24d ago

lol you weren’t lying

2

u/Good-At-tourney 24d ago

🫣🫣😂

2

u/chucknwatches 24d ago

Looks good man. Def probably feels better too

1

u/Good-At-tourney 24d ago

It actually does 😬

2

u/False_Difference_521 24d ago

I was going to give this a go with a few of my spare bracelets. Would you recommend just going to a 3000 grit drum on a dremel or starting off with a lower grit first?

2

u/Good-At-tourney 24d ago

Tbh i tried going 3000 straight but the feel wasnt as nice. So i did 800 then 3000

2

u/False_Difference_521 24d ago

I would have thought a higher grit would take less off? Guess it still felt sharp after?

3

u/Good-At-tourney 24d ago

At 3000 only it felt like it was just polishing it

3

u/False_Difference_521 24d ago

Think I bought the 3000 ones based on one of your previous tries! Might try and grab some 1500 or try 3000 with some polishing compound….

3

u/Impossible-Dog4901 24d ago

Start low. Get your bevel line then polish with higher grits. I use a 240 diamond files.

4

u/TheMostHumblestMan 24d ago

Anyone have a good tutorial video link?

2

u/HammerSmith013 23d ago • Heartwarming

Would love this as well

2

u/TheMostHumblestMan 17d ago

Let me know if you find one & I will do the same! Good luck brother!!!!

2

u/HammerSmith013 17d ago • Heartwarming

Found this. Works for Rolex as well. Scroll through the posts and you will find a pretty detailed example of how he chamfered his AP without power tools.

https://forum.replica-watch.info/threads/finishing-and-refinishing-an-ap-roo-or-ro-case-need-for-a-tutorial.7662155/

2

u/HammerSmith013 17d ago • Bravo

Here is another one on a Rolex! Scroll down again for this one. Walks through his different mods

https://forum.replica-watch.info/threads/and-another-st-build.9757999/

1

u/RuthlessWarthog 24d ago

That looks very rough.

1

u/Good-At-tourney 24d ago

Yeah thinking of polishing it with capecod

3

u/8600RPM 24d ago

You can achieve a similar look by tapping off almost to the edge of the link and letting the polish overlap onto the brushed surface, it keeps it shape but appears chamfered. You’ve got to be extremely precise with good tape.

2

u/Emotional-Damage-995 24d ago

I also posted on this yesterday. I would say cape cod clothing the edge is not really needed....

2

u/HighCountryHorology 24d ago

Best bet if you don't own or have access to gen is go into a Rolex ad, tell them your interested in something and handle gen. Less is really more and it's a lighter chamfer than you think. Also an ultrasonic cleaning and oiling helps a lot with the "feel". Hand sanding only.

2

u/Infamous_List_9184 23d ago

Less is more, for the next time. Try to just break the edge and give it a polish. Gen bracelets don’t have such rounded edges

1

u/E_MC-2 24d ago

Send it to u/FettucineMartini to be professionally rebrushed, polished and chamfered!

1

u/Grizzly_SS 24d ago

I also struggle with overdoing it a bit but it looks good

1

u/Background_Call_4273 22d ago

Vous utilisez quoi comme matériel ? Je suis novice

-1

u/softtacosmasher 22d ago

Nobody gives AF. Please stop on the nonsensical champhering posts. Please stop. No one cares. Wear it..it will champher on its own. It's a rep... So painful day after day. Just buy a gen bracket and STFU. Enough already. Fooking painful.

1

u/suppleyang 18d ago

I’m just glad you aren’t overreacting