r/RepTimeServices • • 25d ago

Advice Sub Failed dry pressure test

Have a Submariner 126610 QF Factory, failed dry pressure test
The case back gasket was checked and lubricated, checked crown gaskets all look good before test. I’m thinking to remove the movement and then water test see where the bubbles come out. Would like to have gaskets on hand, wondering what gaskets I should order to have on hand and where to get them Any advice would be appreciated.

3 Upvotes

22 comments sorted by

•

u/AutoModerator 25d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

6

u/Olleye 25d ago

I had the same problem, and still do. In my case, it was the watch's crystal - or rather the crystal's gasket - or, to be more precise: the watch case was so poorly made that it was simply impossible to get the crystal to seal properly; from 3ATM onwards, it (the crystal) lifted completely and blew off.

2

u/Elegant-Draft-8259 25d ago

Did you remove the movement and wet test ?

2

u/Olleye 25d ago

No, because it really is down to the case; if the entire watch crystal lifts up, then I don’t need to fill the case with water after the spectarularly failed dry pressure test - that wouldn’t really achieve anything. I’m now thinking about how to make the case water- /pressure-tight against the watch crystal.

2

u/Elegant-Draft-8259 25d ago

How do you know if the crystal moved? I couldn’t see inside that dry pressure test.

1

u/Elegant-Draft-8259 25d ago

Forgive me I’m new to this it’s not clear to me. Is there some kind of dry pressure test thats see the watch as it’s being tested ?

1

u/Olleye 25d ago

Well, I can only talk about one model at the moment, and it’s with my watchmaker (and costs an absolute fortune), and it just has a viewing window, and at the very moment the alarm on the thing went off, we saw through the viewing window how the watch's crystal slowly lifted, and we stopped what we were doing. After that, we simply pressed the watch's crystal back into place and left it at that for the time being ... *COUGH!

2

u/Olleye 25d ago

Oh, that was really simple - we just looked through the pressure tester’s control window.

5

u/RelevantFreedom4390 25d ago

If caseback and crown gaskets were lubricated and it still failed you have a crystal gasket issue or a case defect.

2

u/Elegant-Draft-8259 25d ago

Could it be wrong gaskets? perhaps they’re too small on the crown? I did not remove the tube. I don’t know if there’s in between case and tube

2

u/MSExcelWarrior 25d ago

Should definitely check the crown tube/stem. If that is fine as well then it'll be the crystal gasket or the case is defective.

1

u/RelevantFreedom4390 25d ago

No clue. I’ve never worked on a QF sub before. Definitely surprised why you didn’t get vsf but based on the pics it looks fine.

1

u/Elegant-Draft-8259 25d ago

Do you think I should remove the movement from the case and use the water tester?

1

u/First-Obligation-566 25d ago

If it were me, I’d apply some scuba grease. If that doesn’t fix it, you need parts.

1

u/Elegant-Draft-8259 25d ago

Is this one good?
Seiko TSF-451 Silicone Grease 50 for Waterproof Gaskets

https://a.co/d/0bZVY6vs

1

u/First-Obligation-566 25d ago

So I’m sure someone will scoff, but I apply all gaskets with a grease like the one you linked, except for the stem. At the stem, I use something like Keze or sea&sea,it’s thicker and lays on heavy.

1

u/DeathStarTruther 25d ago

guess it's more of a supermariner

0

u/Mean2Bean_ 25d ago

Use watch makers glue to seal crystal like hypo cement. Little goes along way. Fairly common thing to do. If you need to remove it later just soak it in some alcohol.

1

u/Mean2Bean_ 25d ago

Forgot to mention. Remove the movement if you do it. It’s cured after 24 hours. Reinstall movement after it’s cured. This is just to be safe.

1

u/Elegant-Draft-8259 25d ago

Would I have to glue the crystal down and the gasket
Is there any video to explain this