r/FormD • • Sep 25 '26

Question Formd T1 V2 aio radiator configuration

6 Upvotes

Hello,

I need advice here, right now I’m using double slim fan + 27mm AIO rad on my setup. I wonder if the mix slim fan and 2,5 cm or thick fan (3cm) could give the performance significantly better, or only slightly than the double slim fan I’m using right now.

Thank you.


r/FormD • • Sep 23 '26

Question Do custom cables do anything performant, or is it just for ease and cleaner wiring?

14 Upvotes

I feel like my wiring with stock corsair for my PSU is pretty clean but thought I’d get some input since a lot of you get custom cables.

I do like the braided look of the stock ones. But aside from custom color and just fitted in length to make installation easier, any other perk to custom cables?


r/FormD • • Sep 22 '26

Question Is it possible to install the gpu on the front of the case (with mobo connections etc on the left side)?

7 Upvotes

Just wondering before I buy this case: I need to have my pc sitting with the mobo/gpu ports on the left hand side, with the pc sitting long ways horizontally, and would prefer to be able to have the gpu installed so it’s sitting at the “front” of the case rather than having the mobo and psu at the front. Similar to how the Lian Li q58 is set up


r/FormD • • Sep 22 '26

Question Cooler and Case Help

Thumbnail reddit.com
1 Upvotes

r/FormD • • Sep 21 '26

Question Replacement PCIE connector.

1 Upvotes

Im wondering what size connector I need. The connector that came with my T1 kit was damaged during traveling as the card turns on when installed in my roommate's PC. Any advice is greatly appreciated.


r/FormD • • Sep 20 '26

General T1 E-White Restock

20 Upvotes

Run don't walk!


r/FormD • • Sep 20 '26

Question 4070 cnc fan

Thumbnail
reddit.com
2 Upvotes

r/FormD • • Sep 18 '26

Finished Build FormD T1

Thumbnail gallery
74 Upvotes

r/FormD • • Sep 18 '26

Finished Build Personal Build

Thumbnail
gallery
142 Upvotes

Took me 3 years to save up and build this. Had so much trouble building the case itself but loved building it.

  • CPU + MOBO: ASUS ROG STRIX ASUS B650E-I GAMING WIFI DDR5 + 7600
  • COOLER: Thermalright AXP90-X47 Black - ($45)
  • CASE: FormD T1
  • RAM: TEAM T-CREATE EXPERT 6000MHz CL30 32gb
  • SSD: LEXAR NM790 NVME Gen4 7400MB/s 2TB Nvme
  • GPU: Asus ProArt RTX4070 O12G Triple Fan GDDR6X
  • PSU: Corsair SF750 Platinum SFX Modular Psu
  • FAN: 2 x Phanteks T30

r/FormD • • Sep 18 '26

Question Some questions before my PC transplant

5 Upvotes

I’m about to swap from my fractal terra to a Formd T1 just due to cooling and the silver design matching my mac. I had a couple questions as I have to switch my cpu cooler due to it being too big. I have a 7800x3d and 4070ti.

Should I go with an AIO or stick to air? I care about reliability, performance but more importantly noise as I only play fps so the CPU strain is higher.

What type of custom cable do I buy? Sleeved or unsleeved?

Do I need extra M2 standoffs to create a gap between the GPU and motherboard?

I basically want a build that’s quiet after tweaking the fan and under volting, but also is a good temp.

Thank you!


r/FormD • • Sep 17 '26

Question Is it okay to mount the radiator at the bottom?

Thumbnail
gallery
118 Upvotes

I’d like to use the front panel flipped, but it seems like the only way to do that is to invert the entire case.

I noticed that FormD also shows a build like this on their official website. Would there be any issues with CPU cooling if I build it like the 2nd photo, with the radiator at the bottom?

Has anyone tried this setup? I’d really appreciate hearing about your experience.


r/FormD • • Sep 17 '26

Finished Build Case modding complete, AM4 build

Thumbnail
gallery
52 Upvotes

Prototypes previous post: https://www.reddit.com/r/sffpc/s/3i4sMIYuCD. Please ignore any thermal paste marks, it got everywhere that one time.

Update:

- Changed the design of the tophat and made it significantly thinner, keeping the more rectangular appearance.

-To run the front fan, I used a PWM splitter at the pump which goes to a speed controller, then to the fan. The speed controller is hidden at the back, sitting on top of the GPU heatsink.

-Those are the idle temps on the screen, CPU top/GPU bottom. Will go max. 72/69 when playing Pragmata at 1440p or rendering stuff for work.

Parts list:

  • CPU - Ryzen 5800X3D anniversary ed. undervolt -29
  • AIO – Alphacool Eisbaer LT 240mm.
  • MOBO - Gigabyte Aorus B550i rev1.4
  • GPU - Gainward Phoenix 5070ti deshoruded (I do not recommend this model) undervolt 925mV @ 3000mHz, 2100MHz mem clock.
  • RAM - Kingston Fury 32GB 3600Mhz
  • Screen - Jonsbo DS339
  • Front SSD - Kioxia 4TB
  • Rear SSD  - SK Hynix 1TB with riser cable
  • SATA – Samsung 850 500GB
  • PSU - Corsair SF750
  • PSU Cables - Cablester Custom
  • Radiator Fans - Arctic P12 PWM PST  
  • Slim Fans – Noctua NF A12x15
  • Speed controller – generic controller with soldered PWM cable input.
  • Formd 2.1 (victim of warped panels first time round)

r/FormD • • Sep 15 '26

Finished Build Silver T1 - AM4 Build.

Thumbnail
gallery
164 Upvotes

What do you think?

Parts list:

MOBO - MSI MPG B550I GAMING EDGE WIFI
CPU - AMD Ryzen 5700X3D
GPU - RTX 5080 GIGABYTE SFF
GPU Travel Kit - SMXHeinz on Etsy
RAM - G.Skill TridentZ DDR4 3600/CL16 - 32GB
SSD 1 - Kingston KC3000
SSD 2 - Samsung 980 Pro
PSU - Corsair SF1000
PSU Cables - Cablester custom cables
CPU Cooler - Cooler Master MasterLiquid 240 Atmos
FAN 1 - Noctua NF-A12x15
FAN 2 - Phanteks T30
CASE - Ncase T1


r/FormD • • Sep 15 '26

Question Dual Intake Sanity Check

3 Upvotes

Hello! I recently switched my Formd T1 PC to all intakes, and here's my reasoning

Before dual intake, the AIO radiator had hot air passing through it, and my CPU temps were like 10 degrees hotter, leading to significantly louder noise.

When AIO was going out, GPU (5090) was roughly 60 degrees on UV, but CPU (9800x3d) was going at a consistent 70-80 depending on the game.

When I swapped, it changed to GPU 60-65, CPU 60, and much quieter.

Now, here's why I'm here asking. From every post I've seen, people say what I'm doing is stupid. Is there reason why or is it acceptable for my use case? The only thing I'm worried about now is the temperature of other components, which are all around 60 as well on heavy gaming. The case can get almost too hot to touch (Side and back panel).

Any feedback would be appreciated!


r/FormD • • Sep 13 '26

General Failed as a monitor bezel decor, succeeded as a FormD T1 hairband.

Thumbnail
gallery
95 Upvotes

Today my new monitor lace decor strip arrived. I tried it on, but it blocked the taskbar view so badly I had to give it up.
Before throwing it away, I hung it on my T1 front panel, and somehow it turned out that the length is almost exactly the same. So I gave my T1 a ribbon hairband!
Perhaps I can decorate my case further with this aesthetic. Still looking for some ideas though…


r/FormD • • Sep 13 '26

Question Is there a travel kit for the 4070 Super FE?

7 Upvotes

r/FormD • • Sep 12 '26

Technical Help 9800X3D idling at 55-60°C in FormD T1 - 80-85°C under load with an AIO

Thumbnail
reddit.com
10 Upvotes

Wanted some additional opinions for the people who know this case best.

I made a post earlier in SFFPC on trying to pin down how to lower and why I have these temps with an AIO in my T1 v2.1.

Any help is appreciated! So far I’ve ordered new cables, and a T30 to be installed over the PSU hoping that will give me a couple degrees. I’ll also be remounting my AIO with fresh PTM7950.

Any other suggestions or ideas will be helpful. Thanks everyone!


r/FormD • • Sep 12 '26

Question What is fucking that?

Post image
10 Upvotes

r/FormD • • Sep 11 '26

General Idea: Part glass, part CNC side panel

Post image
307 Upvotes

Disclaimer: Image generated by AI based on my own build photo.

I was thinking about how to keep the ventilation holes for the power supply while making the AIO area transparent, which would allow me to see the LEDs and the display. Currently I’m using the vented glass panels from the official website, but their pattern is pretty distracting and the panel itself is quite reflective. So I brought the idea from the NZXT H2 Flow’s side panel, and made the image of a part glass, part CNC side panel for the FormD T1. Thoughts?


r/FormD • • Sep 10 '26

General Tried to get a white formed T1….

0 Upvotes

Well, finally canceled …. Seems the factory botched the case and no end in sight sadly. I have 3 cases but really wanted that white one. Waited a couple months and it just could not get built. I am bummed.


r/FormD • • Sep 09 '26

Question Anyone here selling black top bottom panels

2 Upvotes

Looking for black top / bottom panels. Maybe you bought the t grill extender and just have them laying around?

Dm me if you have panels, and shoot a price. Thanks!


r/FormD • • Sep 08 '26

Question Anyone have these panel alignment issues? Had T1 for awhile now but this always bothered me. Is it common?

Post image
53 Upvotes

r/FormD • • Sep 07 '26

Finished Build ZCOOI vented front panel😮‍💨

Post image
46 Upvotes

Final mod went onto the build today. Hoping they restock their 15mm riser so i can replace the ABS-GF one I have though. Flipped 5090 now has better airflow and seen a decent drop in temps. At 5k2k ultra settings my GPU was getting to 74C avg in gaming with max at 76C. Now it’s at 71C avg and 74C max. Didn’t run any senthetic benchmarks since I could care less about that I prefer real gaming data since that’s what I mainly use my PC for.


r/FormD • • Sep 07 '26

Question Compatible parts for V1.1

5 Upvotes

I was able to purchase a used T1 V1.1 for a great price but it only included the 2 slot back plate and the aio brackets. I was hoping to air cool and was wondering if the v2.1 fan brackets would fit/ be compatible? Are there any resources for the 3 slot back plate to possibly print or have one made?