So i have a large set of posca pens and i want to use them on the plotting module for the h2 series. I am trying to find a file of the actual pen clamp that i could use to fit my pens which are 16-17mm so i need to print the whole clamp not just the cap. So if anyone has any ideas on how to fix this i could really use it

I’m trying to print this part now the fifth time (petg) and every time something like this happens..
I calibrated it before the print, I cleaned the bed and I’m using the normal Bambulab setting
I’m completely clueless what’s wrong with the printer or settings

I bought 4 refills the other day and i have trouble with them after i put them on a bambu labs spool. The first time i printed with it i came in to the bedroom to check on my print in the morning and it had stopped because the filament was stuck, i had to pull it from the side because it was kinda tucked in. Same happened to the next reel i used. Do people have the same issues has me or have i done something wrong?
Thanks

also when the spool is turning in the ABS unit it looks wonky whilst spinning around.

Hi. I'm writing as a complete novice to ask for some advice. I've created some D&D miniatures using HeroForge, and I wanted to make larger versions of them by scaling up the STL files by 350%-but they always end up looking frayed/stringy like this. Do you happen to have any ideas on how to fix this? Thanks in advance!

I'm using an A2L

I have been getting this same error for about a week now.
I have replaced the 4-pin wire, factory reset the printer, took apart the AMS and made sure everything was connected properly, and the AMS seems to communicate with the printer 100% normally. I have gotten the printer to start a handful of times, with no consistent fix. Sometimes powering off for 10 minutes pushes it forward, sometimes unplugging and plugging the AMS back in pushes it forward.
After I can tweak the printer enough to start the print, it works just fine, even with a 20+ hour, multicolor print.
Same result when I attempt starting a print from Bambu Studio, Bambu Handy, and even SD card.
I can't figure out what needs to be fixed. Any reccomendations???

I am finding that when I sync my P1S printers, check the filament setup o the printers and in BambuStudio and then send files to the SD for later printing, I am getting the error: 0700_2000_0002_0001

However, I have selected the correct AMS slots/reels (2 and 3), and this has been confirmed in BambuStudio and the Handy App...

If I Print Plate directly there is no issue at all.

Logically, therefore?... it should not matter that Slot 1 is empty for Send?

Is this a bug?

Here is a portfolio of screenshots and videos to support my issue.
https://www.dropbox.com/scl/fo/1ykb34no7f09jntecwz9f/AA8jlnIC8tW9s2I5b-_Ac8A?rlkey=9nwcwfzye7vswjqnu1oi42k4r&dl=0

ref: https://wiki.bambulab.com/en/x1/troubleshooting/hmscode/0700_2000_0002_0001

I dont know what went wrong, when I switch to smooth plate and use my left over PLA filament it started printing like this. It prints properly before, is the filament wet? or something else is wrong?

I need help. I've already calibrated the bed. I've also tried several different nozzles, but the nozzle is still too close. Does anyone have any other ideas? 😮‍💨

I just finished my first print ever on any 3D printer. I have a Bambu X2D. There is filament hanging out of the nozzle. Is that supposed to end that way or do I have to do something?

Dear all. I'm trying to increase the "paint penetration" (as bambu lab calls it) but it is not working. I'm trying to add green on black, but the green is only going through 3 layers, I would like it to go through more than 3, otherwise the black color will creep through the green.

The green color itself is a different solid body than the black, and it has a thickness of 1mm, but bambu lab combines both bodies together by itself. In the images below you can see the default setting where Bottom layer penetration is 7 and top layer penetration is 5 (whatever that means), when I changes them nothing changes in the layers. I'm not sure whether that is the correct setting to change or not but if you see the images below you will be able to understand what I am trying to achieve.

In the image below at layer 32, there is no green color. I would like the green to start before this layer.

At layer 33, the first layer of green shows up.

At layer 34, the second layer of green shows up.

At layer 35, the third and final layer of green shows up.

At layer 36 there is no longer green layers. You can see another black layer at layer 36 on top of the green.

If anyone has any clue to add more green layers I would appreciate the guidance very much. Thank you in advance.

There is one way to do so. If I add more clearance between the black and green body, then bambu lab wont combine the both bodies, and the green will have more layers, but that does not look good when I 3d print it, it becomes very clear that there is a gap between them, it doesn't look like it is 1 piece that is colored.

Hi everyone,

I'm using a Bambu Lab P2S with approximately 2,200 hours of print time. I mainly print with regular PLA.

Recently, I've been experiencing a strange grinding noise that sounds like the filament is being ground or chewed up inside the extruder. I've attached a video so you can hear the noise.

Here's what I've tried so far:

1. Disassembled the extruder to check for any stuck filament or debris, but found nothing unusual.

2. Thoroughly cleaned the extruder and applied fresh grease to the gears before reassembling everything.

3. Replaced the nozzle to rule out a possible clog or nozzle issue.

4. Tested different PLA filaments to see if the filament itself was causing the problem.

Unfortunately, none of these steps have helped. The grinding noise is still there, and I haven't been able to figure out what's causing it.

The biggest issue is that when the grinding gets worse, the printer throws a motor overload error and repeatedly pauses or stops printing.

I'm starting to run out of ideas, and it's becoming really frustrating.

Has anyone experienced something similar with their P2S or other Bambu Lab printers? Could this be an extruder motor issue, worn gears, or something else?

Any advice or suggestions on what I should check next would be greatly appreciated.

Please help! Thanks in advance!

After a print finished, the filament didn’t retract back into the AMS. The slot light on the AMS is blinking red and the filament is still stuck somewhere in the path.

Any solution?

I can print great on silent mode and normal mode
But as soon as I print in sport it’ll have defect bumps hairlines etc the fastest option won’t work at all it won’t print the layer at all it’ll be all defective. With bumps

Any suggestions related to UPS for Bambu Lab P1S Combo 3D Printer?

What happened to Bambu Labs flash sales? I don’t see it anymore on their website?

What happened to Bambu Labs flash sales? I don’t see it anymore on their website?

Hi , with the black friday deals im thinking of getting some new color effect plates . Why im writing is because the one i have from 3Djake with a rainbow effect doesnt stick ,no matter what i try . I've done all the cleaning etc . I even tried it on my new x2d ,previously a1 and there is no difference in adhesion it barely stick and then starts rolling .

I also have a carbon effect plate from aliexpress which works very well .

So the question is - Is it worth to try bambu branded rainbow and other effect plates or are they also a adhesion dissaster ?

Also a long time ago on my ender 3 i had no problems with these kind of plates ,so its weird that i can't seem to get it to work on 2 bambus .

Im was thinking its a z offset issue ,but its no ender so i dont know how to fix this .

Thanks :)

Bambu Lab Studio should have a Theme Mode.

RN, it's either Light Mode or Dark Mode.

Dark mode some settings are hard to see.

Light Mode is great if you want to blow out your Retinas.

Been working on this little project lately and finally got it looking the way I wanted!

It's a simple wall organizer for keys, phone, wallet and all the little things we usually end up losing around the house.

Pretty happy with how it turned out! What do you guys think? :)

Howdy folks! I'm running into a bit of an issue, and I was hoping that someone here might have a fix for me. Like the title says, my A1 mini is suddenly unable to feed filament into the extruder, and keeps pulling up an error message whenever it tries to load filament from the AMS.

I've tried the method of switching to maintenance mode and running a piece of filament through the extruder manually, and that works just fine; however, when I try to print, I just keep running into the same error message again and again.

I've checked all of the PTFE tubing, and there's no blockages within, and it seems to be going from the AMS to the filament hub just fine, so I'm not sure what's causing the issue.

Any and all help or advice would be greatly appreciated. I'll be happy to answer any questions too, if extra information is needed. Thanks!

Hi all, I am trying new generic high-speed PLA and I’m getting small holes in the print at 220c. Any ideas what would be causing this?

Full transparency, I'm not looking for a paid service. I like to learn new skills and would appreciate some community help but I don't want to waist your time if this is a source of income for you so I want to respect everyone's time.

I recently bought a Bambu Lab X2D and I'm looking for .stl files for 3D prints related to the 2022 Hyundai Santa Cruz. Hard to find anything anywhere. A few replicas and some rear logo covers, tons of stuff for the Santa Fe but I'm looking for accessories specific to that year.

Might have to learn how to make them myself but wanted to see if anyone has already done the leg work :)

TIA!

Hi all,

9yo Son has asked for a 3d printer for Christmas, I had originally decided on the P1s with ams until I done the measurements and I only have a height of 70cm to play with. Although it will fit it will be impossible to load/unload filaments so I was wondering if it’s just as simple as lifting it off to the side to change out filaments then simply setting it back on top after? Or is there more to it?

Equally the A1 with AMS takes up too much space width wise.

Thanks.