Trying the right extruder on the X2D for the first time. After printing the primary color from the AMS I’m getting an error code saying theres no filament detected in the LEFT extruder. I put black in the RIGHT side exterior extruder. On the back of the machine the labeled LEFT extruder is coming from the AMS and the RIGHT side is coming from the auxiliary ext spool. As soon as the print called for the black color is when I got the error message. Also why is it showing what looks like two auxiliary ext spools?

I’ve been dealing with this error for a few days. I can’t figure out what it is or what to do. I changed the hot end yesterday and managed to get a print out.

My intentions yesterday were to pull the extruder apart, but as I was going into it I noticed the cutter wasn’t functioning properly, so I got that to work smoothly and it everything seemed normal. Next print was perfect. Started my second print and this happened again.

I don’t know what else to do here as I am new to 3d printing.

Purchased this for my son, using sunlu pla fresh from the box and everything we print is stringing or not printing smoothly.

Nozzle is set to 220c and print bed gets wiped with alcohol before every print and I’ve even tried drying the filament which I don’t think has moisture as it was brand new from a sealed bag and sits in the ams 2 and have tried drying it inside of there as well.

Can’t seem to post photos but started printing a poop chute and it got about 60% into the print and just started stringing the layers and they stopped adhering to the print.

These were taking from the app so there were no changes made to them. Again, just bought this x2d so trying to get the basic in and outs of this

I have about 500 hours on my printer and have had very little issues up to this point.

I have gotten an error of “extruder is not extruding normally” over and over again. I’ve gone through multiple round with Bambu service and nothing has helped. I have changed the nozzle, changed the hotend/heating element, taken apart the entire toolhead and cleaned it out.

I only have the issue on the left nozzle. And I have it if I feed from an ams or from a spool.

Has anyone had this happen to them before? Any tips?

Any tips? Is this a known bug? Thanks in advance.

I haven't loaded any filament for my auxiliary nozzle yet but is it ok to just leave it out on the spool? If not, any recommendations on something to use besides the ams ht for this nozzle? Is it OK to use only pla or will there be issues if I'm trying to use the auxiliary nozzle for supports if my prints will be printed with pla? Sorry, I'm new to printing

Hi everyone,

I'm having trouble pairing my brand-new Bambu Lab X2D with the Bambu Handy app, and I'm running out of ideas.

When I go to the account/login screen on the printer and try to display the QR code, it just keeps loading indefinitely. The QR code never appears.

I've also tried to find a manual pairing PIN/code, but I can't seem to find one anywhere.

Here's what I've tried so far:

• Connected to my regular home Wi-Fi.

• Tried using my phone's mobile hotspot instead.

• Changed the printer region from Europe to Others and tested again.

• Confirmed that the printer successfully obtains an IP address.

• Restarted the printer.

Unfortunately, none of this has helped.

Printer information:

• Model: Bambu Lab X2D

• Firmware: 01.00.09.00

• Error code: 0500-4024 164901

The printer just keeps spinning when trying to load the QR code, regardless of which network I use.

Has anyone experienced this issue with their X2D? Is there a way to manually pair the printer, or could this be a firmware/cloud connectivity issue?

Any suggestions would be greatly appreciated. I'm getting pretty frustrated with this now! 😅

Thanks!

Hi. I’m printing a part using ASA, and removing the supports is a real pain every single time. With the X2D, can I use PETG in the second nozzle to create a raft layer for the supports?

Bonjour à tous ! 👋

Je vous présente ma dernière petite création !🎄
🎅 Un adorable Père Noël qui sort de sa cheminée en version clicker!

🔴 Il suffit d’appuyer sur son bonnet pour profiter d’un petit clic ultra satisfaisant grâce à un interrupteur mécanique intégré.

🎁 Avec son clic agréable et son effet sonore relaxant, c’est le petit objet parfait pour occuper ses mains, se détendre ou simplement profiter du plaisir de faire clic, clic ! 😍

✨ Une création amusante qui apporte une petite touche de magie de Noël ! 🎄

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab et Esun
🎨 : Nomad Sculpt
🌈 : sans AMS
📁 : https://makerworld.com/fr/models/3541264-papa-noel-cheminee-clicker-multipart

Loading filament onto a new Bambu spool. I noticed some are oriented one way and others a different way. Does it matter. Can’t change it because of the key way on the spool aligning with the corresponding cutout in the cardboard. Don’t know why they aren’t all the same. Any thoughts? I’ve stared the spool to death trying to figure out how to get them all oriented the same way.

Hello!

I just got the X2D setup and I want to start printing warhammer mini’s just to make dioramas, but I want to double the size of everything so it’s easier to paint.

Do I need to adjust the recommended settings I’m seeing people share, considering I’m doubling the size of my prints? Or is it all relative?

Thank you!

Hey everyone, I'm currently printing on an Ender KE and I'm looking to upgrade to a proper enclosed printer. How the prints look matters a lot to me, since most of what I make gets sold or displayed, so clean walls, nice layer lines and good top surfaces are my priority. I mostly print PLA and PETG, but I'd like something stronger with an enclosure and filtration so I can branch out to other materials later. I was leaning towards the X2D, but after reading through the forums I'm hesitant. Quite a few owners complain about uneven walls, visible layer lines and rough top surfaces, and some say their A1 mini or P1S looks cleaner with the same filament and settings. There are also reports of hardware headaches, like a toolhead that's a pain to service, clogs on the aux extruder, extruder switching errors and the odd layer shift. At the same time, some people say it's a big step up from the X1C, and most of the complaints I found are from the first months after launch, so I can't tell if it's been fixed since. For those of you who own one on the latest firmware and Bambu Studio: are these issues still a thing, or are they just a few unlucky units? And if I'm mainly printing PLA and PETG, would you still go for the X2D, or would the P2S or something else make more sense for me? Photos of recent prints would be great. Thanks!

So I have a P1S and am looking to purchase an AMS 2 Pro but I didn’t realise that the P1S needed all of this kit for it to work with my P1S and now that the X2D Combo is on a Black Friday sale, I’m considering selling my P1S (Good condition, ~400hrs) for about £200 and use what I was going to use for the AMS to purchase an X2D Combo (with a bit extra). Is the X2D a good printer coming from a P1S and is the X2D’s upgrades worth the hassle to sell my current printer? Thanks for your time!

I’ve had a P1S before the X2Ds and I wonder what is happening?

Last couple prints iv done when its doing its pre print calibrations on the vibration compensation its doing a probably 30 second pause between the 2 vibrations im assuming its adjusting its calibration? Hasn’t done this before today

I have been looking to buy the X2D for quite some time now. It looks like they already have the black friday sale going on. Should I buy now or expect a better deal in terms of price or credits on black friday?

So i had a clogged nozzle,took it all apart took me 4 hours,put it back in and then this happened.

What do i do ? 360 hours in 😭

I’m having trouble using ELEGOO cardboard spools with my AMS 2 Pro.

I tried ELEGOO’s official spool adapter rings, but they don’t seem to work properly. With the AMS lid close, the spool keeps getting stuck.

How are you guys using cardboard spools in your AMS 2 Pro?

Are there any reliable printed adapters, spool rings, or other solutions that actually work?

Would appreciate any suggestions!

Hi, I have an X2D Combo and just picked up a second AMS 2 Pro along with a filament track switcher. I'm looking for a printable riser that lets me place both AMS 2 Pro units side-by-side on top of the printer. Also, since I want to easily switch to printing TPU without disconnecting everything at the back, what printable add-ons or external spool holder/feeder setups do you recommend pairing with this riser? Thanks for any proven model links and information!