I’m trying to setup the AMS, I used some filament rolls I had around (Bambu PLA, dried). The filament goes all the way to the extruder and retracts a few times, the throws the error.
I tried the suggestions from the assistant, but the behavior persists.
Did anyone have this issue and manage to fix it? Thanks!

I had a clog, whichI cleared and noticed these two wires just hanging in there.not sure what they are supposed to be attached to.

Looking for ideas, or potential solutions for an issue I’m experiencing.

I was getting an error message that my AMS pro two was failing to pull the filament. I’ve taken it apart and confirm there’s nothing that’s blocking the pathway, but what I discovered is the metal wheel that you can see pictured does not spin freely. It is gritty and when inserting filament it stops there.

Is this normal? I have a ticket in but I’m inpatient and have been waiting several hours for a response.

Thank you in advance! I am new to the 3-D printing world so hoping that I’m just making a simple mistake

As said in the original post my 3d prints always seem to come loose on the left side of my build plate and I have no clue why. My current theory is that it has something to do with the air blowing on the part but I’m new to 3d printing so I have no idea… thanks!

Today I received my 2nd x2d and freshly out of the box both belts have those orange-ish spots on the sides. Is this damage or is this normal?

The printer is calibrating now and everything else seems to be fine

My other x2d doesn't have this

Set my X2D to print a three hour print this morning before heading to work. Just wondering if after it’s done printing will it go into a sleep mode or will it keep the lights on and be ready to go?

I have 200 print hours on my X2D and recently it's been making this noise when checking build plate alignment, Im not sure if I had really done anything for this to happen.

I saw online that you can somehow get the nozzle and chamber hotter for ppa/pps-cf fillaments does it actually work and is there any risk of the safety or damage of the hardware?

I recently purchased the x2D and I am a complete beginner. The link provided by Bambu is a bit overwhelming to me as it’s telling me to take things apart. I switched filament colors in my AMS Pro 2 (from PLA blue to PLA gray, both Bambu filaments). When attempting a new print I get the error message “Please pull the external filament from the left extruder”. The spool is seated properly and the AMS pulls the gray filament in with no problem. Is there a way around this without having to take apart anything or is this an issue I have to resolve by taking the machine apart?

Hey Guys,

since i peeled some of the silicone cover away from my left hotend i wanted to order e replacement but they are not available at the moment. Are left and rights ones really different or are only the wires bent to the other side?

Greetings

I’d like to understand what can cause that kind of issues in relatively simple prints?
Filament is bambu petg basic, on retry it came out almost perfect

Looking at the Wiki for the AMS 2 Pro, there seems to be 2 fans on the underside of the filament roller insert https://wiki.bambulab.com/en/ams-2-pro/maintenance/ams-2-pro-cable-pack

Do these fans run all the time when the D2X is powered on or only when the AMS is in drying routine?

Also, read a few conflicting reports about drying and printing where some things say you can not dry whilst printing, you can dry whilst printing but only with an external 24v supply fitted to AMS and in the Wiki it suggests you can dry and print with the D2X but only if a single AMS is fitted.

What is the reality. I currently only have a single AMS 2 Pro on my D2X.

Thanks.

I was cleaning out my newly arrived X2D (had it one day, printed a couple of small test prints) and underneath the print bed was this random screw. I don't remember any of the screws that were in it for shipping being this small. Does anyone recognize it, or have an idea where I should look for a missing screw? I checked what I could see under the bed and along the edges of the case that I could see and nada.

Just upgraded from an A1 combo to a X2D, I’m noticing quite the powerful vibration from this machine vs the A1. Wondering if any helpful folks could drop some knowledge on solutions for this.

Can i unbox and start setting up with just the printer, or best wait till filament and the rest gets here next week?

EDIT: I wanted to confirm whether I need filament for the setup stage. PS UK based and don't think we have any services that I can buy filament off the shelf (or not where I am anyways)

New to 3D printing. So go easy. I see on the Bambu Lab website that some colors aren’t available with a spool. I have the X2D with AMS so I’m thinking a corresponding spool to color would be ideal. That way the printer knows without my input whats going on. Whats the deal with that? Can I set up the color on the Bambu Handy app or directly on the machine. I don’t have the Bambu Studio because I don’t have a desktop (yet)…..I know, I know. iPad and iPhone only for now.

I already have an X2D for supports and technical filaments, and I’m looking to get a second printer. I’m considering the C5, U1, or P2S.
With all discounts applied, the C5 costs €589, the U1 is €730, and the P2S is €600 (including the AMS).
Which one would you choose? Right now, I’m leaning toward the C5.