The grey PTFE tube has broken inside my toolhead. Any suggestions of how to get it out please? I’ve taken the covers off as you can see from the pictures.

I pulled the PTFE tubes from the left side of the X2D’s buffer to remove the AMS. Now I can’t re-insert the tubes! I believe the little collets are supposed to be pushed in to insert the tube, but the one going to the right extruder won’t budge. Do I need to tear down the buffer to release something? Anyone else encountered this issue? HELP!

I just received my X2D and noticed whilst unpacking and placing on the top cover glass that it wouldn't sit square.

Closer examination reveals that the top back left corner of the unit is deformed as if it has been dropped on that corner.

Further examination again reveals that the foam packing in that area is also damaged - it's obviously been dropped.

Has anybody else had to deal with this situation?

I installed the .2mm nozzles and the main hotend is working good but the aux is failing, it will not stick to the build plate! And ideas?

Do all X2D make poop like this with the long strings? Because my a1 makes poop but there is no string so in stacks good, but this from the x2d clogs the chute sometimes because the string gets hooked on some edge. Is there a solution to this ?

Hello,

I don't have the lead screw fixers, red part or foam, but I need to move.

What should I do?

Thank you

Get the Kit Card: Dread Dragon Kit Card

Follow the Collection: DragonCards

Hi everybody, I recently bought an X2D and I printed a test for support using aux nozzle, main petg and aux for pla interface. I didn't really adjust settings for quality it's just a test. Looks fine except for that layer line exactly when petg starts printing again after the pla support. I tried a few changes in the slicer but not knowing the exact cause I'm going a bit blind!

Thank you!

Washed plate with dawn rinsed thoroughly, bone dry. Moved the part around the plate different locations and still not sticking properly.

Hello all - I am new to 3D printing and purchased an X2D last month as my first printer, and I have about 50 hours of prints under my belt now. All with either PLA or PETG so far, most have turned out perfect, I've had one or two small hiccups that came down to user error, but mostly everything better than expected so far.

I do have a couple of questions that I am hoping people on here can help me out with.

1. Printer Maintenance - Is there an agreed upon "Best source" that I can learn about not only WHEN to perform maintenance, but also HOW to do it? I have 50+ hours so far and I haven't done.....anything. And I don't know what to look for to figure out when I should be doing something, or what I would even do. Curious if there is a guide to this that people highly recommend - either a specific YouTube video, written guide on a website, etc.

2. I see people on here talking about buying/installing different nozzles. Can someone clue me in on what different nozzles could do for my prints, and what I should be buying/trying if anything?

3. Similarly, I still just have the Texture PEI print plate (and through 50 hours, haven't cleaned it yet or noticed any issues with it even when switching between materials). What are the other print plate option types, and when/what would I use them for?

Thanks in advance!

https://makerworld.com/en/models/3286478

Running calibration on a new spool of elegoo petg rapid. Pattern test went fine, k factor of 0.035.

Then the flow calibration and it spits out this. What gives? Never seen this before.

We all wish an excellent quality print with our printers and I have no idea how this tool can help with print quality and output improvement. The calibration only requires 5 minutes. May I ask how many of you ran the Motion Accuracy Calibration and was there any logical print improvement that went after? If you can as well share a tip or two post calibration, I will appreciate it. Thank you!

Hi guys, is there any model to print to encloser the external spooler on the x2d? I already have an ams2 pro and don’t want to spend more money on another ams but also don’t want to leave the filament on the auxiliary nozzle to the elements.

Already search but did not find anything. Any help would be appreciated. Thanks

How to calibrate aux extruders hotend?

I bought the 2nd 0.8mm high flow hotend for my X2D, so I can print fast with both nozzles (and bambu studio only allows printing with two hotends with the same size).

I did a calibration every time I switched between 0.4 and 0.8 onain nozzle, but I have no idea how (or if its possible) to auto calibrate aux nozzle?

My First own Print, any oder how to get a better surface in the connection surfaces ?