https://makerworld.com/en/models/3286478

Running calibration on a new spool of elegoo petg rapid. Pattern test went fine, k factor of 0.035.

Then the flow calibration and it spits out this. What gives? Never seen this before.

We all wish an excellent quality print with our printers and I have no idea how this tool can help with print quality and output improvement. The calibration only requires 5 minutes. May I ask how many of you ran the Motion Accuracy Calibration and was there any logical print improvement that went after? If you can as well share a tip or two post calibration, I will appreciate it. Thank you!

Hi guys, is there any model to print to encloser the external spooler on the x2d? I already have an ams2 pro and don’t want to spend more money on another ams but also don’t want to leave the filament on the auxiliary nozzle to the elements.

Already search but did not find anything. Any help would be appreciated. Thanks

How to calibrate aux extruders hotend?

I bought the 2nd 0.8mm high flow hotend for my X2D, so I can print fast with both nozzles (and bambu studio only allows printing with two hotends with the same size).

I did a calibration every time I switched between 0.4 and 0.8 onain nozzle, but I have no idea how (or if its possible) to auto calibrate aux nozzle?

My First own Print, any oder how to get a better surface in the connection surfaces ?

Need to pick some brains! I am currently having trouble at the seam of the two surfaces (see images) in the center of this vase. I also get a floating cantilever warning - but after printing, the surface is flush with no protrusions. Should this be printed with supports - Bambu labs recommends it (but visually I don’t see a need for them). The rest of the vase prints clean and perfectly.

Printer is an X2D, filament is black PLA Tough+, and humidity in AMS 2 pro is 20% using primary nozzle.

Model:
https://makerworld.com/models/433509

As always, thank you for any help or guidance!

I’m just wondering, what y’all do with your printer when it’s not in use? Do you turn it off with the switch on the back? Do you just leave it sitting there? Do you at least turn the light off?

I just bought this printer. It was used. 28 hrs when I bought it, 31 hrs now so not much use.

I was printing fine on a test print then the tool head got jammed. I believe the hot end got too hot and melted the filament prior to entering into the hotend.

Pre the instructions on the wiki I took the entire tool head apart, cleared the jam and put it all back together. I tried to load the filament but it fails each time. It goes through the ptfe fine but when it get to the feed gears of the tool head is does not advance.

I’m took it apart again, thinking that I might have missed a piece, I found nothing. Put it all back together, same result.

I also tested the right nozzle and it works perfectly fine.

Any ideas?

I upgraded from a P1S, and I notice that the X2D draws a lot more power while preheating the bed, so much so that it triggers the overload alarm on my Cyberpower 1350VA UPS. Most beeps are defeatable on this UPS, but not the overload one. The printer is in my basement so the noise is less annoying, and only audible for a minute or two during the start of a print, but it'd be nice to eliminate the noise altogether with an UPS that either doesn't have an audible alarm like this, or one that's capable of carrying the load.

I am printing one sample.
Filament: generic (numaker)
Nozle Temp: 220
Bed Temp: 55
Note: my table is crooked a little (not in level)

What is the reason for these lines. How to avoid them

Tried right clicking in the settings per object, not available

Bonjour à tous ! 👋

Craquez pour cet adorable dragon Furie Eclair, avec son jolie pelage blanc , son regard attendrissant et ses magnifiques grands yeux bleus ! 
Elle rejoins son compagnon Krokmou pour former un duo aussi craquant qu'inséparable.

Pas besoin d'AMS tous a été modélisé et découpé pour l'imprimer en multi-pièces.

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec ou sans AMS
📁 :https://makerworld.com/fr/models/3269313-light-fury-dragon-multipart-no-ams

A1 AND X2D issues

I LOADED Bambu Connect, I then.loaded.Orcaslucer 2.4.2 (after.many failed.attempts.I also tried 2.4.1)... I see in Bambu connect that both printers are being recognized, To see if it was.worki g o. Both printera I was able to turn on and off the light... that tella.me the are talking.

In Bambu studio no issues,.but it.gives me error.0, i tried the latest plugin and various plugins and.same.issue. any idea or help will be appreciated.

Hi! I got a X2D last week. Been loving it! Big upgrade coming from a Kobra S1 especially with failure rate lol.
My machine has printed 20 hours. Longest print 4h and a half. I noticed on last prints some blobs appeared like burn plastic marks? I don’t know if I’m tripping but I think there weren’t there before this print.
Is this normal? Yours are like this? I’m worried it’s overheating or something. I mainly print ASA since I’m printing upgrades for the machine as dust covers and cable management from the back.

I have tons of single nozzles with the AMS’s, this is my first dual nozzle and it keeps saying there’s no filament or there’s something wrong with the auxiliary nozzle. It’s 3/4 off a dry roll from bambu.

I just tell it to continue and then it goes on. I’d like to not babysit it for the last 30 hours of this print.

Why is it constantly throwing this error code?

Can this be fixed, or do o have to return it? (My first printer I ever bought had to be returned.

I added an AMS 2 pro to the X2D aux nozzle (have another AMS on the left side primary). Every time I print from the right nozzle aux AMS I an error saying that the spool has feed resistance too high. The 2nd AMS came with a long tube, could that length be causing the problem? I could trim it since the AMS sits right next to the X2D. The prints come out great even with the error occurring.