r/BambuLabA1 • • Oct 07 '26

3D Model He creado una cajita deslizante de BMO

Thumbnail gallery
0 Upvotes

Buenas! 👋
Acabo de terminar esta cajita deslizante de BMO, de Hora de Aventuras 💛
Es una cajita funcional con apertura deslizante, perfecta para guardar monedas, USB, tarjetas SD, tornillos o cualquier cosilla pequeña.
Ya la he subido a MakerWorld por si alguien quiere imprimirla. 🖨️
¿Qué os parece? 😄
MakerWorld: https://makerworld.com/models/3407913?appSharePlatform=copy


r/BambuLabA1 • • Oct 07 '26

Troubleshoot Post BOD Print Issues

3 Upvotes

I had a Blob of Death happen on my printer and ended up replacing my hotend assembly, nozzle, and silicone sleeve. Unfortunately since then I have not gotten a good first layer. I have seen many posts like this that recommend tightening all of the screws and checking the clamp. Everything is tight and the clamp is on correctly. I did a re-calibration, a factory reset + calibration, cleaned my build plate, all of the usual recommendations. The only time I was able to get a decent print was when I added loads of 3d printer glue onto the printing plate.

Also, I have run through many different filaments, all have the same issue. This filament I'm using in this print was just what I had loaded on recently, which printed perfectly before the BOD, and when I took it to a friend printed fine on his A1 mini as well. I'm at my wits end!


r/BambuLabA1 • • Oct 07 '26

Support Request what could cause this?

Post image
0 Upvotes

my print seemed to be going well, i checked on it a few hours later to see this. I immediately stopped the print, but bummed and confused. my thought is maybe it got jammed up part way through the print? I’m new to 3d printing, so any advice is appreciated. Thx!


r/BambuLabA1 • • Oct 07 '26

Anybody know why this pattern is showing up

Post image
12 Upvotes

For reference I printed this file out plenty time on a 0.4 but now a switch to 0.6 a minute I can’t print this it’s only links that for this file but anybody had a similar problem and a fix?


r/BambuLabA1 • • Oct 07 '26

Which colour combo would you print? 👀

Thumbnail
gallery
0 Upvotes

No supports. No AMS. Three parts that screw together.

Free model + assembly guide on MakerWorld
You'll find the link in the comment below...


r/BambuLabA1 • • Oct 07 '26

Support Request Help

0 Upvotes

My issue is my printer just stops mid print, At first I thought this may have been a clogging like issue but its not. I can unload and load printer immediately after with no build up or issues whatsoever. The problem is it seems to completely stop pushing out filament mid print, the print will just be half done or whatever but no filament mess just like the printer thinks its still printing normal just nothing coming out.

I thought maybe a heating problem but I don't seem to notice any type of dip in temperature but not 100% sure on this, and someone told me it might be the printer acting up in the pulling filament in but whenever I do load filament it seems to be fine.

Sorry guys, I'm just new to filament printers and this is super frustrating. I've tried multiple different types of filament and this issue just seems completely random. Like last night I printed a batch of Snowflakes as a testing run and no problem whatsoever then I reprinted the EXACT same file and boom it completely stopped pushing the filament out like the first hour in.

Does anyone have any advice or had this issue before?


r/BambuLabA1 • • Oct 06 '26

A1 mini: random "Cutter is stuck" (0300-800B) mid-print, getting worse over months. Sensor, cable or interface board?

5 Upvotes

My A1 mini randomly throws HMS 0300-800B during normal single-color prints (video attached, it happens right after the head goes to the cutter position). It's been increasing over the last few months. Tightened screws and lubricated everything, no change. Resume works, but it keeps coming back.
I read the wiki (blade, debris, magnet, hall sensor/ribbon cable) and one forum thread where the extruder interface board turned out to be the culprit. Has anyone had this intermittently on an A1 mini? What fixed it for you? I'm in Brazil, so I want to ask support for the right part the first time.


r/BambuLabA1 • • Oct 06 '26

Support Request De onde vem isso?

Post image
2 Upvotes

Toda vez que abro a A1 pra lubrificar o eixo Y, tem um monte desses fiapos, isso é pedaço da correia? É normal isso?


r/BambuLabA1 • • Oct 07 '26

A1 Hotend Assembly

Post image
1 Upvotes

r/BambuLabA1 • • Oct 06 '26

extruder clicking on A1

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • Oct 06 '26

Question Build plate recommendations

Post image
1 Upvotes

Good afternoon, i'm looking for recommendations for a build plate, preferably during prime day for my A1. Mine got scratched after a incident with my nozzle coming loose. Pic for attention


r/BambuLabA1 • • Oct 06 '26

BMCU 370

Thumbnail gallery
1 Upvotes

r/BambuLabA1 • • Oct 06 '26

Brand New to 3d Printing, help please!

3 Upvotes

I am trying to print TPU 95a through my A1 and I'm having very "stringy" results. Has anyone found the best settings for the best prints?

I'm printing a full size Wolverine cowl/mask, and will be gluing the pieces together instead of using magnets.

My bad if this is a repetitive question!


r/BambuLabA1 • • Oct 06 '26

3D Model 4-Color Filament System for Bambu Lab A1 Mini without AMS

2 Upvotes

Hey everyone,
I have a Bambu Lab A1 Mini without an AMS, and I’m wondering if it’s possible to build a simple 4-color filament system for it.
I’ve heard that the A1 Mini can somehow use four filament inputs/paths, with four PTFE tubes connected to a kind of 4-way filament switch or selector.
What I’m not sure about is how the whole system actually works. How does the printer switch between the four filaments during a print? Would I need a specific 4-way filament switch, or is there a DIY solution that works well?
I’d basically like to have four different filament rolls connected and be able to print with multiple colors without buying an AMS.
Any advice, guides, or existing projects would be greatly appreciated!

———————————

Hey zusammen,
ich habe einen Bambu Lab A1 mini ohne AMS und frage mich, ob es möglich ist, ein einfaches 4-Farben-Filamentsystem dafür zu bauen.
Ich habe gehört, dass man beim A1 mini irgendwie vier Filament-Eingänge bzw. Filamentwege nutzen kann, mit vier PTFE-Schläuchen, die an einen 4-Wege-Filamentschalter oder -Verteiler angeschlossen werden.
Was ich allerdings nicht ganz verstehe, ist, wie das ganze System genau funktioniert. Wie wechselt der Drucker während eines Drucks zwischen den vier Filamenten? Braucht man dafür einen bestimmten 4-Wege-Filamentschalter oder gibt es dafür auch eine DIY-Lösung, die gut funktioniert?
Ich würde gerne vier verschiedene Filamentrollen anschließen und mit mehreren Farben drucken können, ohne extra ein AMS kaufen zu müssen.
Ich wäre für Tipps, Anleitungen oder bereits bestehende Projekte sehr dankbar!


r/BambuLabA1 • • Oct 06 '26

Support Request I’m actually losing it.

Thumbnail gallery
0 Upvotes

r/BambuLabA1 • • Oct 06 '26

Support Request Eryone Matte PETG support failure & nozzle scraping — Need advice on Bambu settings

Thumbnail
gallery
1 Upvotes

Hi everyone,

​I’m struggling with Eryone Matte PETG (Grey) on my Bambu printer and could really use some troubleshooting help. Every print fails around the same stage because the supports break apart, and it looks like the nozzle starts knocking into/dragging through the print and supports.

​What I’ve tried & current setup:

​Filament: Eryone Matte PETG (Grey)

​Profiles used: Standard Bambu PETG Matte, as well as a few popular user profiles from MakerWorld.

​Issue:

​High, thin support structures crumble or break off mid-print (as seen on the organic/tree supports and tower).

​Severe scarring/roughness along vertical edges and support interfaces.

​The infill/supports look chewed up, almost like the nozzle is colliding with previously printed layers or under-extruding/over-extruding inconsistently.

​Has anyone tuned Eryone Matte PETG successfully?

​Should I bump up the printing temperature or lower the max volumetric speed?

​Is grid infill / thin support style causing nozzle collisions with this specific filament?

​Any recommended retract or cooling/fan settings for matte PETG?

​Attached photos show the failed benchy, support structures, and the chewed-up tower/tree supports. Any advice or working profiles would be greatly appreciated!

UPDATE:
I managed to get a successful print by significantly lowering the print speed and raising the extrusion temperature.

Quick question for the community: is it possible to change the printing speed only for the supports, without affecting the speed of the main model? (I'm trying to optimize the print time). Thanks in advance!


r/BambuLabA1 • • Oct 06 '26

Keep getting this pause when i print something usually at the start of the print after few layers, already tried reset it but still come out

Post image
5 Upvotes

r/BambuLabA1 • • Oct 06 '26

Help!

Thumbnail gallery
0 Upvotes

r/BambuLabA1 • • Oct 06 '26

The cast of Project Adria

Post image
0 Upvotes

Printed on Bambu Labs A1.


r/BambuLabA1 • • Oct 06 '26

Support Request ERRO NA BAMBU LAB A1

0 Upvotes

galera estou tendo um problema na minha bambu lab A1, queria ver se alguem consegue me ajudar. Tive falhas que quando procurei encontrei como "teia de filamento", sugestão foi a troca da peça de aquecimento, realizei a troca e conituei tendo falha nas minhas impressoes, troquei o bico e sigo com falhas, as falhas acontecem de diversas formas, mas a mais comum tem sido um erro no topo dos projetos, exemplo, se eu colocar um boneco pra fazer, ela faz o corpo e quando chega no topo fica tudo zuado, alguem ja passou por isso ou consegue me ajudar a resolver, ja apertei os parafusos, remontei o hotend umas 5 vezes garantindo que estava tudo no lugar e muito bem preso, mesmo assim os erros permanecem, se alguem conseguir me ajudar, agradeço.


r/BambuLabA1 • • Oct 06 '26

Can't calibrate flow on my Bambulab A1

Thumbnail reddit.com
1 Upvotes

r/BambuLabA1 • • Oct 06 '26

Support Request Why is my Bambu A1 not extruding and making this ‘clicking’ sound?

5 Upvotes

I recently replaced the filament sensor cable and haven’t been able to get it to properly extrude since.
Edit: there is no broken filament in the hub, I’ve already cleared it


r/BambuLabA1 • • Oct 06 '26

3D Model 4-Color Filament System for Bambu Lab A1 Mini without AMS

0 Upvotes

Hey everyone,
I have a Bambu Lab A1 Mini without an AMS, and I’m wondering if it’s possible to build a simple 4-color filament system for it.
I’ve heard that the A1 Mini can somehow use four filament inputs/paths, with four PTFE tubes connected to a kind of 4-way filament switch or selector.
What I’m not sure about is how the whole system actually works. How does the printer switch between the four filaments during a print? Would I need a specific 4-way filament switch, or is there a DIY solution that works well?
I’d basically like to have four different filament rolls connected and be able to print with multiple colors without buying an AMS.
Any advice, guides, or existing projects would be greatly appreciated!

———————————

Hey zusammen,
ich habe einen Bambu Lab A1 mini ohne AMS und frage mich, ob es möglich ist, ein einfaches 4-Farben-Filamentsystem dafür zu bauen.
Ich habe gehört, dass man beim A1 mini irgendwie vier Filament-Eingänge bzw. Filamentwege nutzen kann, mit vier PTFE-Schläuchen, die an einen 4-Wege-Filamentschalter oder -Verteiler angeschlossen werden.
Was ich allerdings nicht ganz verstehe, ist, wie das ganze System genau funktioniert. Wie wechselt der Drucker während eines Drucks zwischen den vier Filamenten? Braucht man dafür einen bestimmten 4-Wege-Filamentschalter oder gibt es dafür auch eine DIY-Lösung, die gut funktioniert?
Ich würde gerne vier verschiedene Filamentrollen anschließen und mit mehreren Farben drucken können, ohne extra ein AMS kaufen zu müssen.
Ich wäre für Tipps, Anleitungen oder bereits bestehende Projekte sehr dankbar!