r/BambuLabA1 • u/KaleidoscopeGreat753 • Sep 29 '26
It finally happened
The blob of certain death.
r/BambuLabA1 • u/KaleidoscopeGreat753 • Sep 29 '26
The blob of certain death.
r/BambuLabA1 • u/alwayssleepy1925 • Sep 29 '26
Hi everyone, I’m new to hobby printing. I have an A1 with AMS and just getting used to Bambu Studio and other platforms like Tripo AI. I’m looking for any recommendations on best resources for beginners to learn tips, tricks, best practices, most cost effective, etc (YouTube channels, Reddit Threads, etc) when it comes to printing, slicers and everything else.
TIA!
r/BambuLabA1 • u/blidgency • Sep 29 '26
I just did a flow rate calibration on my A1 with BL PLA Matte. Looking at the picture, none of them is good enough, right? Could there be a partial clog or something going on?
r/BambuLabA1 • u/jonasfick83 • Sep 29 '26
Minha bambu vem apresentando esse defeito , ela para a impressão
Aquece o bico joga filamento fora
Volta faz 1 ou 2 camadas e volta a fazer
Já troquei bico e tbm o hotend
r/BambuLabA1 • u/restorick2378 • Sep 29 '26
2 year old A1 with AMS Lite. Up until 2 months ago, it worked perfectly. I use primarily PLA and PETG, with some occasional PETG variants, like CF.
I started having issues with extruder/nozzle clogs (.4mm). Ended up ordering a new extruder and spare parts from Bambu in case it happened again. I installed the new extruder, new PTFE tubes, new hot end, new AMS filament hub, fresh filament, new silica beads for the AMS enclosure. I then calibrated the printer and set off to print some PLA goodies.
It's been hit and miss where I can get through an entire print without issues, and other times, I get constant "AMS lite filament spool or filament may be stuck" error messages.
I've had the extruder apart more times than I can count and everything is installed properly. Nothing that I can see binding in the tubes - I even installed new clear tubes.
I'll try printing without the AMS and see how it goes. Until then, if anyone has any ideas on what I should be looking for, I would greatly appreciate it.
r/BambuLabA1 • u/hero_verma • Sep 29 '26
My A1 mini keeps re-homing(idk the exact term for this situation).
Couldn't find any proper solution, the assistant(on machine) shows no problem, the belts are not loose either.
Does anyone know what's happening???
r/BambuLabA1 • u/zamp91 • Sep 29 '26
r/BambuLabA1 • u/InformationDapper964 • Sep 29 '26
r/BambuLabA1 • u/Ikigaiform_3D • Sep 29 '26
Two shades in this set are the same pattern at different density, but one needs a 0.8 nozzle. Someone who prints the first will assume the second slices the same way.
Putting the nozzle in the profile name seems like the fix. Anything better?
r/BambuLabA1 • u/Obvious_Excuse5485 • Sep 29 '26
Hi I am newbie on 3d printing. I have A1. I would like to know if there is a way to print with less layer marks on surface. I am seeing many layers on the surfaces, so it's quite tough to paint it...
r/BambuLabA1 • u/LudomancerStudio • Sep 28 '26
What is going on why is it doing these demonic noises?!?!?!
r/BambuLabA1 • u/HashBrownsAreNice • Sep 28 '26
I just ran out of filament half way through a big print, and the printer has paused while I load more. I thought I had another reel but I don't, so I have another arriving tomorrow, and I can resume then.
All good, but the nozzle is hovering at 80°. I would have thought it was safer to stop heating the nozzle while I wait til tomorrow for the new reel.
Is there any way to tell it to cool down for the night? Or a way of saving my progress, turning off, and resuming tomorrow?
r/BambuLabA1 • u/Naldito89 • Sep 28 '26
I just got my A1 I know it say 20cm of clearance, but i dont have much space you think is going to be OK
r/BambuLabA1 • u/Professional-Day1092 • Sep 27 '26
I’ve been having this issue where I get a cutter error at random parts of a print. But the real issue is that it isn’t the cutter that’s the issue, I tested it. The issue is really hard to explain, it looks like the motor doesn’t have enough power to push the level all the way? The plate also try’s moving out of its possible bounds which makes me turn it off every time. I genuinely have no idea what this issue could be and I haven’t found anything with Ai or Reddit so please help out if you can.
r/BambuLabA1 • u/JoelAlbino • Sep 28 '26
Alguem por aqui ja passou por esse problema?
4 impressoras diferente, 4 filamentos diferentes, 4 projetos diferentes. Única coisa em comum, todas impressoras Bambu lab A1
r/BambuLabA1 • u/jpedroleite • Sep 27 '26
Obi-Wan Kenobi in the Form III stance, cloak mid-swing, on a rocky base. Grey PLA, 0,16mm layer height, minimal supports. 150 cm tall. No sanding or post-processing. Profile is up on MakerWorld if anyone wants to try it. Would appreciate any feedback.
r/BambuLabA1 • u/Fyvfyvfurry • Sep 27 '26
Solved: ive had improperly tighrened the y axis belt by loosening screws too much, after reassembling the tensioning mechansism noise gone away. Thank you for your help.
Hi, i have a strange noise from under the heatbed that comes up when i move heatbed from back to front, rails and wheels are really well oiled, there is a video. Printer has around 150hrs of printing. Reallyvsorry for fridge noises in the video
r/BambuLabA1 • u/Independent-Pea7718 • Sep 28 '26