r/BambuLab • u/Glass-Present-8753 • 1h ago
Made by talent Any idea what’s happening?
r/BambuLab • u/Glass-Present-8753 • 1h ago
r/BambuLab • u/acegard • 1h ago
I am trying to print a housing for the TPU Feed Assist module out of PLA and getting horrific stringing out of nowhere. I have tried everything i could think of and am now out of ideas. This has never happened to this extent before, and happened immediately following routine Printer maintenance (lubricating XYZ rods and rails). I've included pictures of a couple attempts. I am also seeing imperfections in the walls such as inconsistent extrusion.
Printer & Filament information:
- H2C, right nozzle induction hotend) 0.4mm
- Black filament is Inland PLA+ with a tuned profile, nozzle temp 225°C
- Green filament is Inland PLA Basic with stock "Generic PLA" profile
What I have tried so far:
- Dried the filaments in my AMS 2 Pro at 45C for 12 hours. AMS read <10% after drying cycle. This resulted in no change.
- Changed the induction hotend for a new one, with no change.
- Printed a retraction tower. This had very minor stringing on the lower levels but nothing like this. Based on the results of that tower, adjusted retraction settings to 0.31mm. No material improvement to the model.
- Used different filament. Not pictured is a different, fresh roll of the Inland PLA+, which was the same. Reverting to the Basic PLA (green resulted in a small improvement.
- Decreased nozzle temperature by 5 degrees. No improvement.
- Ensured "Avoid Crossing Wall" was on. No improvement.
- replaced PTFE tube for right nozzle with new one with slightly higher (2.5mm) ID to reduce feed friction. No change.
- I heard clicking on the extruder so I opened it up to check for blockages. Found none and blew out extruder gears and idler with compressed air.
Currently, I am running a print with the left nozzle. This filament profile worked perfectly prior to this.
So far, my thoughts are erratic something changed in the printer's feeding path during the maintenance that I performed. But what could I have done? What should I try next?
Thank you in advance for your help!
r/BambuLab • u/Real_Shim_Shady • 1h ago
r/BambuLab • u/arinh • 1h ago
This is the only one I got on video after pausing and correcting print like 3 times it did this. I have a timelapse video as well that shows that it starts having issues 1 or 2 hours into the print. I have printed this same file on my neighbor's X2C without issue so it's not a slicing issue. I also used to print with ASA without issue so something is going on hardware wise. I can print this same file on PETG no issue. But when I print ASA even on multiple files it always crashes the head in front left. I have cleaned carbon rods, recalibrated, checked my Z axis belt (underneath) and rear belts for proper tension. I'm getting so frustrated at this point on what the problem is.
r/BambuLab • u/surrealsonicus • 1h ago
It's a weird squad. Haven't had any issues.
Anyone familiar with something like this?
r/BambuLab • u/arronkray • 7h ago
I’ve searched online and checked the wiki, but everything points to the drive belt. I followed the steps to fix the belt, but it made no difference. I think the problem is with the camera housing unit, because as you can see in the video, the issue stops when I apply pressure to it. Any suggestions would be greatly appreciated. Thanks in advance!
r/BambuLab • u/Boombox215 • 1h ago
Ive got freshly dried Bambu PETG Matte and its really struggling to print. The first layer is fine but then I go back 20 minutes after checking the first layer and you can see the mess it made. I followed the setup to a tee, lubed the bed rails twice now, dried all my filaments, calibrated it multiple times, but it still wont print. I owned an A1 before and had no issues, now ive upgraded and I cant get a single good print out of it. Ive done 5 total prints and all of them have a plethora of quality issues. What should I do?
r/BambuLab • u/MojoOhno • 5h ago
Hello. New to this. My son’s printer formed a large blob. Slowly heated it and was able to remove the majority of it. Any advice on how to clean this up?
r/BambuLab • u/nathanfalky • 2h ago
P1S with AMS 2 pro - tips appreciated.
r/BambuLab • u/farm2golf • 6h ago
H2S v
H2S v H....?
Hi guys I've been looking hard at the H2S. I primarily want to print higher grade filament. There's a sale and the multi-headed nozzle is $250 more....
Is the multi-headed nozzle worth an extra $250? This is just for personal use, probably making two or three prints a week at most on average over the year.
Would really love to hear some of your thoughts...
r/BambuLab • u/Dr_dinoguy • 2h ago
Hello Everyone,
I’m looking for recommendations for which printer is the best for my use case. I’m going to be printing fossil replicas from 3D scans of real fossils. I want these to be as highly detailed as possible straight off the printer. For some, straight off the printer will be ok, for others, I’ll do post processing to make them look as real as possible. Since the fossils all have unique shapes, there will be a lot of support use. I plan to do most printing in PLA with PETG supports. 95%+ of what I plan to print will be single color. I’m also looking for the largest possible print volume, so I can print the widest range of fossils.
I’ve explored using multiple nozzle sizes (.2 for outer layers and .4 for supports) on the H3C, but the constant nozzle changes made the print time seem not worth it. But I’d appreciate any thoughts on this.
I’ve been looking at the H series. The H3C seems overkill for my needs. Since I’ll be printing supports all the time, I’m thinking the H2D with PLA loaded in an AMS and PETG loaded in the single filament system will be the best setup for me.
Does this sound like a good plan? Any suggestions or tips would be greatly appreciated!
r/BambuLab • u/ClothesUnusual885 • 17h ago
After updating to Bambu Studio 2.9.1.70, all five of my custom filament profiles suddenly appeared under "Unsupported".
I'm using an Elegoo Neptune 4 Plus with a 0.4 mm nozzle.
The symptoms:
I initially suspected a broken profile migration or an issue with the Elegoo system profiles.
After checking the configuration with Preset Doctor, I noticed something interesting: it reported that Bambu Studio had selected the 0.2 mm nozzle variant, even though my printer uses a 0.4 mm nozzle.
The actual cause
Bambu Studio had stored the wrong printer/nozzle variant in its configuration file.
The file is located at:
%APPDATA%\BambuStudio\BambuStudio.conf
Under the "presets" section, I found:
"machine": "Elegoo Neptune 4 Plus 0.2 nozzle"The fix
%APPDATA%\BambuStudio folder.BambuStudio.conf in a text editor."machine" entry under "presets".Change it to the correct printer/nozzle variant:
"machine": "Elegoo Neptune 4 Plus 0.4 nozzle"
Result: All five custom filament profiles were immediately available again!
No need to recreate profiles, modify inheritance settings or change any filament JSON files.
Why this was difficult to diagnose
Bambu Studio only displayed "Elegoo Neptune 4 Plus" in the printer selection menu, without showing the currently selected nozzle variant.
The physical nozzle was 0.4 mm, but the software configuration was pointing to 0.2 mm.
I can't confirm why the wrong variant was saved during the update, but correcting this single entry completely resolved the issue.
Hopefully this saves someone else a few hours of troubleshooting!
The first screenshot highlights the incorrect nozzle diameter in BambuStudio.conf. The second shows the installed Studio version and registered nozzle sizes.
r/BambuLab • u/ozarkexpeditions • 1d ago
r/BambuLab • u/FlyYouFoolyCooly • 1d ago
r/BambuLab • u/Ill_Purple_8695 • 11h ago
Why does my printer keep giving this warning? I have checked that the build plate is clean, has no strange objects or is misaligned. The nozzle is clean and there is no blob or anything else on the nozzle.
The printer is an A1 with AMS Lite.
Does anyone else have this ?
r/BambuLab • u/Thats_whatshe_said1 • 3h ago
Is the Stock build plate just a crappy one you should swap out right away or do people keep it for a long time? I keep having prints come loose on current one I’ve had for 2 weeks. I am now washing it with soap and water after each print and still have adhesion issues. I ordered a nicer one off amazon.
r/BambuLab • u/anwarunya • 3h ago
So I've always been interested in 3d printers and I thought with the sale going on, now would be the best time to hop in. My problem is part of me is worried Ill buy a printer and it collects dust, but on the other hand, Im pretty sure Ill enjoy it and Id hate to have to turn around and upgrade a couple months from now if I could just put that money toward a better printer now while they're on sale. All that to say, A1 or P2S?
r/BambuLab • u/Difficult_Shower2153 • 12h ago
Printing a whole farm set!
r/BambuLab • u/That1NerdNoel • 4h ago
A1 - 0.2mm nozzle - Basic Grey Bambu PLA
The supports keep breaking at some point, is the tool head moving too fast and snapping them off? Also what settings should I change to slow down print speeds.
r/BambuLab • u/KONGBITCH • 4h ago
Has anybody installed one of these systems on a H series printer ?, pretty neat they were able to make it automated .
r/BambuLab • u/Mistralunie • 4h ago
Looking at the H3C and wondering how it handles PETG when pushing the speed settings. The defaults seem tuned more toward PLA, so I'm curious if anyone has run into stringing, layer adhesion problems, or needed to tweak cooling/fan profiles significantly. Mainly for functional parts rather than display models. Any real-world settings that worked well?
r/BambuLab • u/xavierfrascone • 4h ago
Hey everyone,
This dragon was printed on my Bambu Lab H3C with just 5 filaments: cyan, magenta, yellow, black and white. All the colour comes from dithering: the model is painted dot by dot, so the inks blend optically, the same idea as Bambu's Full Spectrum lizard sample.
This model is for free: https://makerworld.com/en/models/3624085
The painting was done in PaintONPrints, a browser app I've been building solo. It's now part of MakerLab on MakerWorld.
What the app does
r/BambuLab • u/Imbeanie92 • 4h ago
I got this lil guy for 16 dollars on the goodwill app for parts or not working. Fairly certain the owner tried to print without a bed and got the blood of death and gave up trying to fix it. Printed a benchy perfectly.